HVAC, Plumbing, and Electrical Experts in Byron Center

Completed annual cooling maintenance on Carrier HVAC system as part of 3-year recurring service agreement. Performed comprehensive inspection of air handler and condenser unit, checking refrigerant levels, electrical connections, and overall system operation. Verified proper function of Aprilaire humidifier integration with the system. Cleaned and inspected all accessible components, tested thermostat operation, and confirmed adequate airflow throughout the ductwork. System operating within manufacturer specifications with no issues identified. Documentation photos captured for service records.

Completed QUOTR-quoted HVAC repair involving refrigerant replacement on residential system. Accessed attic-mounted equipment through ceiling opening and performed necessary refrigerant recovery and recharge procedures. Additional repairs were completed as specified in the quoted scope of work to restore system to proper operating condition.

Completed annual cooling maintenance on 21-year-old Carrier air conditioning system. Performed comprehensive tune-up including inspection of condenser unit, verified proper operation of compressor and fan motor, cleaned condenser coils showing moisture accumulation, checked refrigerant levels, and inspected electrical connections at top access panel. All components found operational with normal wear for unit age; system cycling properly and maintaining adequate cooling capacity.

Completed annual heating and cooling maintenance on residential HVAC system including furnace and air conditioning tune-up procedures. During inspection, discovered significant frost and ice buildup on evaporator coil refrigerant lines, indicating restricted airflow or possible low refrigerant charge. Performed comprehensive system evaluation including visual inspection of burner assembly, blower motor operation, gas valve functionality, electrical connections, and condensate drain lines. Documented frost condition with photographs for service records. System requires follow-up diagnosis to determine root cause of icing issue—likely restricted airflow from dirty filter/coil or refrigerant system problem. Heating components including ignition system and blower assembly visually inspected and found operational. Unit is a 2011 model with no humidifier installed.

Completed full HVAC system installation including new Amana outdoor condensing unit and high-efficiency furnace. Installed outdoor condenser on exterior wall with proper electrical disconnect box and conduit routing, positioned unit on ground-level pad with adequate clearance. Interior installation included furnace with complete ductwork connections, PVC condensate drainage and venting system, flexible supply ductwork, and new air filtration. All electrical connections, refrigerant lines, and mechanical systems tested and verified operational. System commissioned and ready for service.

Completed full installation of new air conditioning condenser unit on exterior concrete pad with proper clearances from building structure. Unit secured to pad, refrigerant lines connected and properly insulated, electrical disconnect installed on building exterior, and all penetrations through siding sealed. System charged to manufacturer specifications per unit label, startup performed, and operational testing confirmed proper function of all components.

Completed annual cooling tune-up on 2011 Goodman AC system. Upon inspection, discovered severely clogged evaporator coil with heavy accumulation of dust and debris restricting airflow. Cleaned coil thoroughly, replaced air filter, verified refrigerant levels, tested system operation, and confirmed unit is functioning properly for the cooling season.

Completed full HVAC system installation including indoor air handler unit in basement utility area with new metallic ductwork runs and elbow connections. Installed outdoor condensing unit on concrete pad with proper gravel base, connected refrigerant lines and electrical disconnect box mounted to exterior wall. All components properly secured, labeled, and tested for operation per manufacturer specifications.

Completed annual cooling maintenance and inspection on residential air conditioning system. Performed standard tune-up procedures including filter check, refrigerant level verification, electrical connection inspection, and condenser coil cleaning. Unit is operational; however, noted that outdoor condenser is not level on concrete pad, which customer has expressed concern about. Recommended scheduling follow-up service to address leveling issue to prevent potential long-term compressor damage and ensure optimal system performance.

Completed annual cooling maintenance on 24-year-old Payne air conditioning system. Upon arrival, found condenser coil heavily clogged with dirt, dust, and debris accumulation, significantly restricting airflow and reducing system efficiency. Performed thorough coil cleaning to restore proper heat transfer and airflow capacity. Conducted standard tune-up procedures including refrigerant level check, electrical component inspection, and operational testing to ensure system readiness for cooling season.

Completed annual cooling maintenance on 2021 EnergiAir heat pump system under comfort club agreement. Performed comprehensive AC tune-up including system diagnostics with digital multimeter, verified capacitor operation reading 792 microfarads, inspected all electrical connections and wiring harnesses, and confirmed proper compressor function. All components operating within manufacturer specifications with warranty coverage extending through June 2026.

Completed full air conditioning system replacement at residential property. Removed existing outdoor condenser unit and installed new gray/silver condenser on level concrete pad against exterior wall with proper clearances. Connected refrigerant lines with insulation to indoor air handler, installed electrical disconnect box, and verified all connections meet code requirements. System tested and operational.

Conducted on-site plumbing estimate for laundry room addition project. Assessed existing utility area layout, including current washing machine placement, electrical panel accessibility, and available space for proposed plumbing installations. Documentation completed with photographic records of work area conditions. Follow-up visit scheduled to provide revised quote for laundry addition scope of work.

Completed residential water heater installation in basement utility area. Installed new cylindrical tank-style water heater on concrete floor with proper metal drip pan for leak protection, connected copper supply lines with brass fittings and shut-off valves, and established electrical connections and venting system per manufacturer specifications and local building codes.

Rerouted furnace exhaust piping system in basement mechanical room to correct improper venting configuration. Installed new white PVC exhaust pipes with proper support brackets and purple mounting straps, ensuring code-compliant vertical and horizontal runs with appropriate pitch for condensate drainage. System tested and verified operational upon completion.

Responded to service call for leaking 20-year-old electric water heater in basement. Inspected 50-gallon unit and documented existing plumbing connections, including copper supply lines, brass shutoff valve with blue handle, flexible connectors, and associated fittings. Photographed installation showing aging infrastructure and provided estimate for water heater replacement due to unit reaching end of serviceable life.

Responded to non-operational sump pump causing water backup in basement. Upon arrival after 6:30 PM, inspected sump pump system with black rubber cover plate and white PVC discharge piping. Evaluated pump mechanism, check valve assembly, and exterior discharge configuration including brass ball valves and weathered piping connections. Restored system to proper working order, eliminating backup condition and ensuring adequate water removal capability.

Completed annual heating and cooling tune-up on 11-year-old furnace and air conditioning system. Performed standard maintenance procedures including filter inspection, electrical connections check, and system operation verification. Addressed client concern regarding furnace noise levels; assessed unit operation and determined noise within normal range for equipment age, provided explanation of typical operational sounds for this model.

Responded to no-heat call on recently installed EnergiAir furnace (model WT 01-2034). Upon arrival, found unit would not initiate heating cycle. Diagnostic testing revealed tripped safety water switch preventing furnace operation. Inspected condensate drainage system and found blockage causing water accumulation in secondary drain pan, which triggered the safety switch as designed. Cleared condensate line obstruction and verified proper drainage flow. Reset safety switch and cycled furnace through complete heating operation to confirm proper function. Unit fired successfully with no fault codes. Verified all safety devices operational and condensate system draining freely. Educated homeowner on importance of condensate maintenance and signs of potential drainage issues. System restored to full operational status.

Completed installation of new residential water heater in basement utility room. Successfully connected copper supply lines, installed proper safety fittings, and ensured all plumbing connections were secure and code-compliant. Unit is fully operational with appropriate electrical panel access maintained for future service needs.