HVAC, Plumbing, and Electrical Experts in Byron Center

Completed scheduled tune-up maintenance on 5-year-old Generac generator unit. Performed comprehensive inspection of internal components including motor assembly, capacitor, valve systems, and electrical connections. All components found to be in proper working condition with connections secure and system operating within normal parameters.

Responded to plumbing leak at 22-year-old residential property where issue began one day prior. Upon inspection, located broken pipe at exterior ball valve assembly mounted on building exterior near utility meter. Valve showed significant weathering, corrosion, and age-related deterioration with rust visible at stem connection point. Repaired/replaced damaged section and verified proper valve operation. Documented conditions with photographs showing exterior plumbing configuration, valve assembly with 600 WP rating markings, and connection points against vinyl siding. Confirmed repair resolved active leak and restored system integrity.

Technician returned to property to complete access work in basement closet space. Opened and accessed confined crawl space area with PVC plumbing infrastructure, including drain and vent piping with elbow connections installed between floor joists. Work completed within estimated timeframe, with photo documentation of existing pipe configuration and installation conditions in the enclosed space.

Responded to water heater leak in drain pan. Upon inspection, found an 11-year-old Bradford White water heater (Model M150T6FBN, 67,000 BTU natural gas, installed May 2015) with active leaking into the collection pan beneath the unit. Given the age of the water heater and presence of leak, documented the existing installation including all plumbing connections, expansion tank, circulation pump, copper piping, PEX connections, and associated mechanical components. Photographed the unit's specification label and overall system configuration for assessment and future reference.

# Drain Diagnostic Service Responded to customer complaint of gurgling sounds in kitchen sink drain occurring when adjacent laundry room was in use. Upon arrival, inspected both the kitchen sink plumbing and laundry room connections to identify the source of the drainage issue. Examined the double-basin stainless steel kitchen sink and verified the symptom description. Inspected laundry room utility connections including water supply valves and drain lines. Diagnosed the gurgling as a venting issue caused by inadequate air circulation in the drain waste vent (DWV) system, which creates negative pressure when the laundry drains, pulling air through the kitchen sink trap. Explained findings to customer and provided recommendations for resolving the venting deficiency. Documented conditions with photographs of both the kitchen sink area and laundry room plumbing connections for reference.

Successfully completed full air conditioning system replacement at residential property. Removed existing outdoor condensing unit and installed new HVAC condenser on concrete pad adjacent to exterior wall with white siding. Ran new refrigerant lines from unit to structure, secured electrical conduit and wiring to exterior wall, and installed disconnect box per code requirements. Unit positioned in landscaped side yard area with proper clearances maintained. All electrical connections completed, system tested, and verified operational. Installation includes proper labeling and safety documentation affixed to equipment.

Completed annual cooling maintenance on 2013 air conditioning system. Performed comprehensive tune-up including inspection of refrigerant lines, evaporator coil assembly, and condensate drainage system. All refrigerant line connections examined and found secure with proper insulation intact. Verified condensate pump operation and drain pan condition. Inspected electrical connections and wiring throughout air handler unit. System operating within normal parameters upon completion of preventive maintenance service.

Completed full HVAC system installation including new Carrier furnace unit in basement utility area and exterior condensing unit on concrete pad. Installed vertical ductwork with proper metallic tape sealing, routed refrigerant lines and electrical conduit through exterior wall via PVC housing, and verified all connections between indoor and outdoor components. System commissioned and operational with proper airflow and refrigerant charge confirmed.

Completed annual cooling maintenance on 16-year-old York air conditioning system. Performed comprehensive tune-up including system inspection, cleaning, and operational testing. Placed drain pan to monitor condensate drainage during service visit.

Replaced malfunctioning garbage disposal unit under kitchen sink. Disconnected existing disposal from drain lines and electrical supply, removed old unit, and installed new black garbage disposal with proper mounting hardware. Verified all plumbing connections are secure and leak-free, tested electrical operation, and confirmed disposal operates correctly with adequate drainage.

Responded to no cooling call on six-year-old Carrier unit with complete system failure affecting entire home. Upon inspection, discovered outdoor condenser coil heavily clogged with dense accumulation of dirt, dust, lint, and fibrous debris significantly restricting airflow and preventing proper heat transfer. Performed thorough coil cleaning to remove blockage and restore system operation. Unit tested and confirmed cooling restored to normal operating parameters.

# ASTU-AC Super Tune-Up Completed Performed comprehensive AC super tune-up on residential air handler system. Inspection revealed significant biological growth and mineral deposits in drain pan requiring cleaning and treatment. Addressed moisture accumulation issues, tested refrigerant lines, and conducted full system diagnostics to ensure optimal performance and efficiency.

Returned to property to complete previously quoted HVAC repair involving ECM blower motor replacement. Disconnected power to unit and removed existing failed motor from air handler assembly. Disconnected all wiring harnesses from motor including multi-speed connections to control board. Removed motor mounting hardware and extracted old motor from blower housing. Installed new ECM motor, secured mounting bracket, and reconnected all electrical connections to control board terminals. Verified proper wire routing and secure connections at both motor and board. Restored power and tested system operation across all speed settings. Confirmed proper blower operation and airflow. Unit operating as designed with new motor functioning correctly.

Completed air conditioning system replacement in residential basement mechanical room. Removed existing AC unit and installed new condensing unit with associated refrigerant lines and electrical connections. Verified proper integration with existing furnace and ductwork system, confirmed all electrical connections meet code requirements, and tested system operation to ensure proper cooling cycle and airflow. Unit is fully operational with all safety controls functioning as designed.

Responded to customer complaint of AC making starting noise with fan failure on 10-year-old system. Upon inspection, diagnosed failed blower motor and capacitor. Replaced defective blower motor assembly and run capacitor, restoring proper airflow and eliminating abnormal starting sounds. Tested system operation through complete cooling cycle, verified proper amperage draw, and confirmed normal fan operation at all speeds.

Replaced worn Moen cartridge in bathtub faucet to restore proper water flow and temperature control. Disassembled existing faucet handles and spout assembly, removed old cartridge, installed new OEM replacement cartridge, reassembled fixtures, and tested operation to ensure leak-free performance.

Completed full air conditioning system replacement at residential property. Installed new outdoor condenser unit on existing concrete pad with proper clearances and leveling, positioned adjacent to utility room access door. Interior installation included new furnace unit in basement utility area with complete ductwork connections, proper venting, and integration with existing plumbing and electrical systems. All work performed per manufacturer specifications and local code requirements, system tested and operational upon completion.

Responded to no cool complaint on 8-year-old EnergiAir system with condenser fan motor not spinning. Upon inspection, accessed control board assembly and found failed capacitor preventing compressor and condenser fan operation. Replaced defective dual run capacitor, verified proper electrical connections to circuit board, and tested system startup. Unit now cooling properly with condenser fan spinning and compressor operating within normal parameters.

Responded to no cooling call on 24-year-old Bryant air conditioning system with complete failure of all components. Upon inspection, discovered severely corroded and damaged wire connector at capacitor terminal, preventing power delivery to outdoor unit. Replaced failed connector and verified proper electrical connections throughout system. Tested unit operation and confirmed compressor, condenser fan motor, and all components restored to normal function with proper cooling achieved.

Responded to an early availability call for a leaky copper pipe. Upon inspection, located the source of the leak in the copper plumbing line running through the framed wall space. Repaired the compromised section of copper piping and verified all connections were secure and leak-free. Confirmed proper water flow and pressure restoration to the shower fixture following the repair.