HVAC & Plumbing Services in Grand Rapids, MI

Successfully installed new residential furnace in basement utility area, complete with proper PVC venting system and connection to existing ductwork. System was mounted against framed wall with all safety labels intact and verified operational before completing service.

Identified and repaired a leaking pipe behind the sink with significant corrosion and mineral buildup. Replaced damaged sections of copper piping and valve assemblies that had caused water damage to the surrounding wall area, and restored proper water flow without leakage.

Corrected B-vent connector from water heater to existing chimney liner that was installed backwards, as indicated by flow direction arrow stamped on B-vent. Replaced improper single wall vent connection that was incorrectly screwed to male end of Hart and Cooley B-vent with manufacturer-approved listed chimney liner to B-vent connector per code requirements.

Successfully completed installation of new heating and cooling system including furnace with metal ductwork, air conditioning components, and water heater with proper copper piping connections. All units were professionally mounted with appropriate venting, and system was verified operational with all connections secure and properly insulated.

Performed annual heating maintenance service on furnace and humidifier system. Cleaned condensate drain pan which showed evidence of standing water and debris accumulation. System restored to proper operating condition with all components inspected per manufacturer specifications.

Performed annual maintenance service on 7-year-old EnergiAir furnace (model WT 02-2029, manufactured 2018). System was thoroughly inspected with no issues found. Completed standard tune-up procedures to ensure optimal operation for the heating season.

Inspected 30-year-old non-functioning radiant heat system. Located and accessed copper supply lines through drywall to diagnose issue. Visual inspection revealed deteriorated copper piping within the wall cavity requiring repair to restore system functionality.

Performed annual tune-up on 39-year-old Coleman furnace. Inspected ductwork system, including flexible air ducts and connections, noting normal wear consistent with system age. No humidifier present; system appears to be functioning within normal parameters despite age.

Responded to toilet with continuous running water issue in half bath. Inspection revealed significant mineral buildup and staining in tank. Replaced flush valve assembly to resolve water flow problem that had persisted despite previous valve kit replacements.

Replaced defective shower valve assembly that was causing stuck hot and cold handles. Inspected outdoor spigot during service visit and identified PVC supply line connection with proper purple primer at joints. All fixtures now operating correctly with smooth handle movement.

Completed return visit to address previously reported shower issues. Tightened loose shower handle, cleared slow-draining shower drain, and properly mounted shower head to ensure flush installation against wall. All fixtures now functioning correctly with proper water flow and drainage.

Inspected electrical system after client reported concerns about improper ground wire installation following previous plumbing work. Verified and corrected grounding issues on the basement plumbing system, ensuring proper bonding of copper pipes to electrical ground. Additionally, upgraded basement lighting and installed permanent wiring to replace temporary electrical connections, bringing all systems into compliance with current electrical code requirements.

Completed annual heating maintenance on two Ruud furnaces (14yr) and two Carrier humidifiers (15yr) with Comfort Manager installed in 2020. Inspected water heater system with proper venting and connections, and examined HVAC ductwork penetrations through wooden framing, confirming all components are functioning properly.

Completed annual heating tune-up on 16-year-old Carrier furnace with attached humidifier. Identified and documented active leak from humidifier unit. System is paired with 1-year-old EnergiAir air cleaner (model WT 12-2034). Photographed installation components showing normal wear on mounting hardware and condensate drainage system for documentation.

Performed comprehensive annual furnace tune-up on 2-year-old EnergiAir WT 07-2033 unit for Comfort Club member. Inspected control module connections, verified proper operation of all components, and documented system condition with photos. No humidifier maintenance required. System functioning within normal parameters.

Successfully installed new furnace and air conditioning system in residential basement. Complete installation included proper mounting of furnace on protective pad, connection of all necessary PVC venting/drain lines, and verification of copper line connections. System was tested and confirmed operational with all safety labels and documentation properly affixed.

Completed estimate for replacement of 25-year-old furnace and air conditioning system per customer request. Documented existing HVAC equipment in basement mechanical room, including current connections and installation configuration. Also assessed outdoor unit location and surrounding concrete patio area for proper equipment placement considerations.

Successfully completed quoted shower valve/trim replacement requiring creation of drywall access point to expose existing plumbing. Removed damaged brass valve assembly, installed new fixture with proper copper pipe connections, and ensured system functionality with no leaks before closing access point.

Successfully installed a new shut-off valve in the basement near the sump pump location. Completed copper pipe connections with appropriate fittings and secured the vertical pipe with a metal bracket against the concrete wall. All connections were tested for proper functionality and no leaks were detected.

Diagnosed intermittent heating issues on a 2-year-old furnace that was failing to reach set temperature. Found condensate drain system partially obstructed causing pressure switch malfunction. Cleared drain line, verified proper operation of pressure switch, and confirmed system now heating consistently to temperature.