HVAC & Plumbing Services in Grand Rapids, MI

Responded to a no-heat call on a one-year-old furnace and inspected the integrated furnace control board, finding a disconnected blue wire with an insulated spade connector not terminated at the board. Verified the control board's programming label and wiring harness condition, then secured the loose connection to restore proper circuit continuity for the ignition and control sequence. Confirmed the unit remains under manufacturer warranty coverage.

Performed annual heating tune-up on a 9-year-old furnace with humidifier service, including a borescope inspection of the internal heat exchanger and cabinet areas. Observed rust staining and corrosion residue on the cabinet floor near the pressure switch, inducer housing, and drain hoses, as well as on interior metal surfaces, indicating possible moisture or condensate intrusion; recommend monitoring and further evaluation of drain and hose connections.

Performed annual furnace and humidifier tune-up, inspecting the humidifier housing, drain hose, and clamped connections within the cabinet. Documented heavy rust and corrosion on fasteners, the humidifier plate fittings, and the cabinet base pan, along with mineral residue and staining indicating prior moisture or leakage. Recommend monitoring the condensate and humidifier drain lines and addressing the source of moisture to prevent further corrosion.

Inspected the reported slow floor drain and opened the wall cavity behind the furnace to trace the drain line, then checked the nearby sump pit, which contained murky sediment and debris around the discharge piping. The affected drain and sump piping were evaluated and the area was left accessible for further service or repair if required.

Diagnosed the under-sink leak and traced the source to the garbage disposal unit, which has a cracked rubber splash guard/hopper and a hairline crack in the housing seam, along with significant corrosion and rust staining on the lower canister. The drain hose, clamp, and PVC connection were inspected and ruled out as leak points. The disposal is beyond serviceable repair and replacement is recommended; a bucket was left in place to catch residual water until the unit is replaced.

Inspected the water heater and identified corrosion and rust staining at the braided stainless steel flexible water connector fitting on the tank's top. Evaluated the cold-water supply connection, brass shutoff valve, and PEX transition, and noted dust accumulation on the tank, deteriorated mortar where the galvanized vent connector meets the masonry wall, and rust-colored sealant staining at the adjacent plenum seams. Documented all conditions with photographs for the service record.

Removed and replaced two existing air conditioning units, installing new equipment and verifying proper operation. During the changeout, a scorched control circuit board with visible burn damage at the solder joints was identified and removed from the air handler cabinet. Outdoor condenser pad area was cleared and the units were set in place.

Responded to a no-heat call on an 11-year-old Trane gas furnace that was running but not producing heat. Inspected the furnace cabinet and evaporator coil plenum area, noting dust and debris buildup on the coil section and loose, torn foil-faced insulation wrap. Diagnosed the heating system and recommended repairs to restore proper heat output.

Inspected the water heater, which was leaking at the base and had lost efficiency with age, and confirmed the tank had failed and required replacement. Verified the temperature-and-pressure relief valve and discharge piping were properly routed to the floor drain, and checked the flue vent connection at the masonry wall, noting the deteriorated mortar patch around the vent opening.

Performed annual heating maintenance on the furnace, including inspection of the cabinet, ductwork connections, and condensate/drain tubing. Verified secure panel fasteners and proper tubing routing, and noted dust and debris buildup near the framing and cabinet seam. Unit operated normally upon completion of the tune-up.

Responded to a no-heat call on a furnace blowing cold air following a recent tune-up. Inspected the draft inducer motor, pressure switch assembly, vent hose connections, and wiring harness inside the burner compartment, verifying that all wires were properly routed, secured with cable ties, and free of damage or loose connections. Confirmed the pressure switches and hose were correctly connected, then cycled the unit to verify proper ignition sequence, burner operation, and warm airflow at the registers.

Performed a Furnace Super Tune-up on a unit approximately 10+ years old, including inspection and verification of system components and operation. Inspected the insulated copper line and shutoff valve assembly, noting split pipe insulation that was re-secured with a zip tie, and organized and secured the low-voltage control wiring bundle at the equipment to maintain proper connections.

Performed a rental inspection on one gas furnace and one gas water heater, with the furnace access panel removed to visually assess the burners, wiring, blower motor, and control components. Inspected the PVC vent piping, flexible and rigid ductwork, plenum connections, and water heater piping, and found no visible frost, rust, or cracking. Documented equipment condition with photos and noted clutter around the mechanical area.

Responded to a reported malfunction on a 9-year-old Rheem Classic Series gas tank water heater and inspected the unit, its gas supply piping and shutoff valve, and the galvanized flue/vent connection at the ceiling penetration. Observed soot staining and debris around the flue opening with a gap between the vent pipe and the ceiling cutout, and noted the surrounding area is cluttered with stored materials near the appliance, which may affect combustion air and clearance; repair options were quoted on site.

Removed the existing water heater and installed a new Bradford White gas-fired water heater in the utility closet. Connected the gas supply with a gas control valve, flue venting, and water lines, and installed a drain line and drip pan beneath the unit. Verified proper operation and checked all connections for leaks.

Installed a new Carrier gas furnace in the basement utility area, connecting it to the existing galvanized supply ductwork, plenum transition, and whole-house humidifier. Routed and secured the galvanized flue vent to the existing chimney path with foil-taped joints, and tied in the condensate drain to the existing PVC line. Verified electrical connections at the unit's junction box and completed system startup and operational checks.

Performed annual heating tune-up on an 8-year-old Bryant gas furnace, including inspection of the plenum, condensate drain piping, and associated components. Observed a corroded humidifier water supply rod/line secured with a hose clamp at the plenum, and noted that the humidifier was not operating. Verified furnace operation and documented the findings, with humidifier repair or replacement recommended to restore humidification.

Installed a new high-efficiency gas furnace in the utility closet, connecting it to the existing supply and return ductwork, gas line, and PVC condensate drain. Routed PVC venting for the condensing unit, reconnected the humidifier to the plenum, and set the furnace over a drain pan with all manufacturer warning labels in place. System was left properly installed with filters on hand and no visible damage or leaks.

Performed an on-site estimate for a 19-year-old water heater reported to be leaking from the top, inspecting the tank top, hot and cold water supply connections, shut-off valve, and flue venting assembly. Observed water-spotting and mild residue on the flue elbow sections, and the unit's age indicates it has exceeded its typical service life, so replacement is recommended and the estimate was documented with photos.

Performed an Electrical Club Inspection of the main service panel with the cover removed, evaluating the main breaker, branch circuit breakers, conductor routing, and terminations. Identified disorganized, fanned-out conductors with possible frayed insulation at the upper panel area, debris within the enclosure, and loose, unterminated low-voltage wiring adjacent to the panel. Recommend a licensed electrician perform a follow-up evaluation to clean and organize the panel wiring, verify and correct terminations, and properly terminate or secure the low-voltage conductors.