HVAC & Plumbing Services in Grand Rapids, MI

Performed annual heating maintenance on 5-year-old EnergiAir furnace per Comfort Club membership. Conducted electrical component testing with multimeter to verify proper operation and inspected internal components. System is functioning within manufacturer specifications.

Responded to service call for ice maker malfunction following previous plumbing work. Inspected refrigerator water supply line and connection valve, finding the blue inlet valve had not been properly opened after the earlier service. Restored water flow to the ice maker by correctly positioning the valve and verified proper operation before completing the service.

Diagnosed intermittent knocking noise in 25-year-old furnace. Inspection of heat exchanger assembly revealed normal operational sounds due to expansion and contraction of aged metal components. Unit is functioning properly despite age; recommended continued monitoring as these sounds are typical in older systems.

Replaced faulty shower faucet exhibiting significant corrosion and oxidation on copper pipe connections. Installed new backflow preventer valve with proper fittings and verified proper operation of the yellow-handled shutoff valve. Documented repair with photos showing completed installation with all components securely connected to the existing plumbing system.

Responded to inspector correction requiring protection at the end of conduit at ceiling. Installed protective bushings on exposed conduit ends and secured metal conduit to OSB sheathing with appropriate fasteners to complete the 80% furnace installation approval requirement.

Responded to emergency no-heat call, diagnosed Lochinvar boiler system which was operational but not delivering heat. Inspected Smart System control panel showing normal temperature readings (system at 88°F/143°F, tank at 120°F/120°F, outdoor at 43°F) and verified all components were functioning correctly. Determined issue was with thermostat communication to boiler; reprogrammed thermostat settings to restore proper heat delivery to residence.

Responded to no-heat call for system less than one year old; accessed mechanical room to diagnose issue, opened furnace panel to inspect internal wiring and circuit board connections. Found loose connection on control board, secured wiring, and verified proper system operation before closing unit.

Diagnosed and repaired toilet with improper flushing and handle leak; replaced worn ballcock assembly and flush valve which had significant mineral buildup causing the malfunction. Verified proper water level and tested flush operation after installation of new components.

Completed replacement of reverse osmosis filtration system including new storage tank and bar sink faucet in kitchen. Installed three new shut-off valves in cabinet, replaced leaking drain line section connected to toilet and shower branch with new eye trap and piping, and repaired leaking water pipe section above well tank with new piping and spigot.

Responded to no hot water complaint on 13-year-old Bradford White water heater. Inspected unit and ventilation system, focusing on the vent pipe connection through the wall which showed signs of wear and improper sealing. Repaired flue connection and restored hot water functionality to the system.

Responded to no hot water call for 10-year-old Rheem water heater that would not light. Upon inspection, diagnosed ignition system failure and performed necessary repairs to restore proper operation. Confirmed water heater functioning correctly with hot water production before completing service.

Assessed customer's existing gas water heater for potential replacement. Inspected installation location in basement utility area, noting current unit's connection to gas line and venting system through ceiling. Documented surrounding infrastructure including HVAC system and available space for new unit installation.

Performed annual maintenance on 1-year-old Carrier furnace (model WT 12-2034). Inspected circuit board which displayed "HL7" code on digital readout with amber indicator light illuminated. System has functioning humidifier. Documented condition with photos and completed preventative maintenance per manufacturer specifications.

Installed supplementary water safety switch in the condensate pan of existing HVAC system. New switch provides redundant protection against potential water overflow conditions. No charge service completed as quoted.

Performed annual heating tune-up on a 2016 CM system. Inspected basement mechanical room with circulation pump, pressure regulator, and copper piping. Noted significant water staining on concrete floor indicating possible previous leaks; system currently operational with no humidifier present.

Successfully installed new Amana furnace in basement location, including proper connection of intake and exhaust PVC venting. Ensured secure mounting on concrete floor, completed all necessary ductwork connections, and verified system operation before completing service.

Repaired leaking pipe fitting in wall by replacing faulty rubber gasket and securing with new stainless steel hose clamp. Inspected surrounding area for water damage and confirmed proper sealing of the connection to prevent future moisture intrusion.

Conducted comprehensive assessment for new air conditioning system installation at side-by-side condo property. Inspected existing outdoor unit location (currently enclosed in protective cage adjacent to brick exterior wall) and evaluated interior Carrier furnace system with connected ductwork in utility room. Documented current system configuration with photographs to facilitate accurate equipment sizing and installation planning for replacement AC system.

Completed correction on ventilation system per inspector's requirements. Modified single wall vent connection at mortar sleeve, ensuring proper crimping and installation of vent pipe directly to Z-flex liner per manufacturer specifications. Documented completed work with photos showing proper venting through concrete block wall.

Performed annual heating system maintenance on customer's furnace. Inspected burner assembly which showed significant corrosion and rust on the burner heads. Noted additional corrosion issues on internal components and inspected wiring connections and pressure switch functionality. Completed standard tune-up procedures to ensure proper operation for the heating season.