Top-Rated HVAC & Plumbing Services in Kalamazoo, MI

Performed the quoted filter housing modification on the air handler and verified system operation by checking the control board status indicator, low-voltage connections, and electrical readings with a clamp meter. Inspected the thermostat backplate wiring and terminal connections, confirming secure low-voltage conductors at the control terminals, with no visible damage, frost, or corrosion at the unit.

Performed annual heating tune-up on furnace, inspecting and verifying operation of system components. Inspected condensate drain assembly, including PVC condensate piping, condensate pump, and float safety switch in the secondary drain pan; confirmed wiring was secure and the safety switch indicator was active. Noted slight dampness and staining in the drain pan, with no active leak observed, and system was left operating properly.

Performed scheduled annual maintenance on a Honeywell standby generator powered by a Generac G-Force engine. Inspected the engine compartment, including the oil filter, air filter housing, intake and exhaust components, hoses, wiring, and enclosure insulation, and found all components clean and in good condition with no signs of rust, leaks, or damage. The unit was verified to be in proper working order following the tune-up.

Assessed a leaking standard tank-type, natural gas Rheem Performance power-vent water heater manufactured January 2021, with evidence of moisture at the base of the tank, and documented the existing power-vent assembly, PVC venting, flexible water connectors, shutoff valve, and surrounding copper piping. Findings support full unit replacement, and the estimate was prepared for a like-for-like power-vent tank replacement.

Removed the existing kitchen faucet and garbage disposal from the double-basin sink and installed the customer-supplied brushed stainless pull-down faucet with matching soap dispenser. Reconnected the angle stop valves and supply lines, restored the drain assembly with the dishwasher drain line, and verified proper operation with no leaks.

Responded to a slow-draining shower with gurgling at the toilet, indicating a partial obstruction in the main drain line shared by both fixtures. Cleared the blockage using drain cleaning equipment and restored full flow, then verified proper drainage at the shower and confirmed the toilet no longer gurgled during operation.

Assessed the renovation area for reconnection of the toilet, sinks, and shower fixtures. Site is currently unfinished, with bare OSB subflooring, patched drywall, and an uncountered base cabinet in place. Fixture reconnection will proceed once finishes and cabinetry are complete.

Repiped the basement drain line using new white PVC with fitted elbows, couplings, and a wye, and connected it to the existing galvanized drain with a secured rubber transition coupling and band clamps. Installed a pump-in-a-box system, routing the discharge through the foundation wall, and completed the work over a 1.5-day period.

Inspected the furnace and surrounding ductwork, flue venting, and condensate and water lines in response to water leaking only during heating operation. Evaluated the galvanized flue and duct connections for condensation and moisture staining, and documented the findings with photos. Verified that heating operation remained functional and identified the likely moisture source for further corrective action.

Responded to a no-heat call on a Carrier furnace installed approximately one year ago and inspected the unit's integrated control board and status display. The board's seven-segment LED displayed a fault code, and the low-voltage terminal connections (24VAC, W, Y, G, C, DHUM) and wiring were visually inspected with no evidence of burn marks, corrosion, or damage. Documented the fault code and board condition, and reviewed the unit's data label to verify the age and installation date for the warranty coverage determination.

Installed a new Bradford White gas water heater in the basement, connecting the gas supply, water lines with flexible connectors, and venting to the existing flue. The unit was set in a drain pan with the discharge piping routed to the drain, and the system was verified for proper operation with no leaks or visible defects.

Performed annual heating tune-up on furnace and humidifier, including inspection, cleaning, and operational verification of all components. Inspected the outdoor condensing unit, which showed no signs of frost, rust, or damage. Replaced smoke alarm batteries with customer-supplied batteries.

Installed a new Carrier gas furnace in the basement mechanical area, connecting it to the existing supply and return ductwork via a galvanized plenum. Routed and secured the galvanized flue venting with proper elbow transition, connected the gas supply using a flexible gas line with a shutoff valve, and attached the unit data and warning labels. Verified all connections are secure, with no visible leaks, rust, or damage, and left the equipment documentation with the unit.

Inspected the tiled shower enclosure for a repair estimate, evaluating the rain-style showerhead, slide bar with handheld unit and braided hose, dual-lever valve trim, and glass enclosure hardware. Fixtures and tile surfaces appeared intact with no visible damage, leaks, or buildup, and the findings were documented with photos to support the repair estimate.

Responded to a no-heat call and inspected the furnace/air handler cabinet, including condensate drain piping, wiring, and supply ductwork. Verified supply plenum temperature of approximately 141°F using a digital thermometer, confirming the unit was producing heat, and checked plenum seams and foil-tape connections for leaks or deterioration with none found. Unit was operating within normal temperature range upon completion.

Removed and replaced the existing 50-gallon natural gas atmospheric-vent water heater, reconnecting the gas supply, copper water lines, pressure relief valve, and exhaust venting to the existing flue. Installed a water softener, tied into the water supply and drain, and verified proper operation, leak-free connections, and safe venting.

Responded to a no-heat call on a 24-year-old Payne furnace that failed to start following a prior service visit. Borescope inspection of the heat exchanger revealed hairline cracks and localized buckling in the metal, along with carbon and debris buildup at the base of the tubes. The cracked heat exchanger is a safety hazard (potential flue gas and carbon monoxide leakage), so the unit was deemed unsafe to operate and left off pending heat exchanger or furnace replacement.

Performed scheduled maintenance tune-up on a Generac 24kW standby generator as part of a recurring service plan. Inspected the engine, valve cover, spark plug area, hoses, oil filter, control panel, and enclosure insulation, finding all components clean and in good condition with no visible rust, cracks, or damage. The unit was also enrolled in the recurring generator maintenance program for continued scheduled service.

Performed scheduled annual maintenance on an 11-year-old Generac standby generator with an OHVI engine, including inspection of the enclosure, engine compartment, battery, and control panel. Replaced the Generac Genuine Parts oil filter and serviced the engine oil, noting the service date on the filter. All components were found clean with no evidence of leaks, rust, frost, or damage, and the unit was left in proper standby condition.

Performed annual heating inspection on a 10-year-old Carrier system, including a full operational check and evaluation of the filtration system. Inspected the air filter, which showed only light discoloration with no significant debris buildup, tearing, or damage, and confirmed it was properly seated. Noted the condensate pump is dusty with visible grime and has loose wiring terminals hanging at the cable end, recommending cleaning and electrical connection inspection; no humidifier is installed on the system.