Heating, AC, Plumbing & Generators in Portage MI

Responded to report of water leak and malfunctioning mini-split system with two bedroom units shutting off prematurely after short runtime. Inspected 9-year-old Daikin mini-split system including outdoor condenser unit and indoor wall-mounted air handlers. Documented exterior condenser unit condition and interior components including condensate drainage system and refrigerant lines. System requires further diagnosis to determine cause of intermittent shutdown and water leakage issue.

Completed annual cooling maintenance on 9-year-old Airtemp air conditioning system. Performed comprehensive tune-up including inspection of all major components, refrigerant levels, electrical connections, and condensate drainage system. Observed condensate pump in operational condition with properly secured PVC piping and drainage lines. All mechanical equipment inspected and found functioning within normal parameters for routine preventive maintenance visit.

Responded to call for leaking 15-year-old tank water heater in basement with water observed leaking from bottom of unit. Upon inspection, confirmed active leak from base of tank indicating internal tank failure, consistent with age and expected service life of residential water heater installed in 2011. Documented existing installation including plumbing connections, electrical wiring, condensate pump assembly, and PVC venting configuration. Provided estimate for complete water heater replacement including removal and disposal of failed unit, installation of new tank water heater with appropriate venting, and reconnection of all water supply lines and electrical components to restore domestic hot water service.

Completed annual cooling maintenance on 19-year-old Trane system. Upon inspection, discovered outdoor unit electrical compartment heavily contaminated with organic debris, dried grass, nesting material, and dirt accumulation throughout wiring connections and components. Thoroughly cleaned electrical panel, removed all debris from compartment, inspected all wire connections and terminals for damage or corrosion. Verified system operation, checked refrigerant pressures, tested capacitor function, and confirmed unit cycling properly. Documented equipment condition with photos. Recommend monitoring electrical compartment for future pest intrusion and potential seal improvements to prevent recurrence.

Completed full air conditioning system replacement including outdoor condensing unit and associated refrigerant line connections. New unit was installed on existing concrete pad, charged to manufacturer specifications with 87 oz total refrigerant charge (A2L safety group refrigerant). All electrical connections, refrigerant lines, and service ports were properly installed and tested. System was commissioned and verified operational with indoor air handler unit. Financing paperwork was processed and activated same day as installation.

Completed full HVAC system replacement including installation of new furnace with air handler, air conditioning unit, and water heater in basement mechanical room. All equipment installed to manufacturer specifications with proper venting, ductwork connections, electrical hookups, and plumbing configurations. System tested and verified operational with financing paperwork processed for same-day completion.

# Drain Pan Replacement Replaced heavily corroded condensate drain pan on indoor HVAC evaporator coil unit. The existing white metal drip pan exhibited extensive rust deterioration along edges and bottom surfaces, compromising its integrity and creating potential for water damage. Removed old pan from beneath copper coil assembly and installed new replacement pan. Verified proper drainage through existing PVC condensate line. Inspected copper coil condition and electrical connections during service. Tested system operation to confirm proper condensate collection and drainage function. Unit returned to normal operation with no leaks detected.

Completed estimate visit for new Generac automatic standby generator installation at 15-year-old single-family residence. Evaluated existing electrical service panel configuration and available space for generator transfer switch integration. Documented current 200-amp main electrical panel with adequate breaker capacity and determined optimal equipment placement for proposed generator system.

Completed annual cooling maintenance on 2018 Lennox 21 SEER system. Performed comprehensive tune-up including inspection of condensate pump operation, verified proper drainage function, and documented equipment condition with photos. All components operating within normal parameters at time of service.

Responded to service call for non-functioning Nest thermostat that would not hold charge. Upon inspection of the Carrier furnace system, diagnosed faulty C-wire (common wire) connection at the HVAC control board. Verified proper 24VAC power supply, cleaned and re-terminated the C-wire connection at both the furnace terminal strip and thermostat base. Tested thermostat functionality and confirmed proper charging and communication with the heating and cooling system. Unit now operating normally with stable power supply to thermostat.

Completed installation of Bradford White residential water heater in basement utility room. Connected copper supply and distribution lines to unit, installed metallic vent pipe system for proper exhaust ventilation, and verified all plumbing connections are secure and leak-free. Unit tested and confirmed operational with proper temperature settings and safety controls functioning as specified.

Completed annual cooling maintenance on a 7-year-old air conditioning system with horizontal air handler located in basement crawl space. Performed comprehensive system inspection, verified proper operation of all components, checked refrigerant levels, cleaned condensate drain system, and documented equipment condition with photos showing air handler unit and associated ductwork in good working order.

Completed comprehensive plumbing inspection addressing water heater maintenance and drainage concerns. Performed tune-up service on Bradford White Defender Safety System water heater, inspecting all connections, temperature and pressure relief valve, and combustion components. Evaluated basement plumbing system including copper supply lines, pipe mounting brackets, and drainage functionality to identify and resolve reported drainage issues.

Conducted estimate for water heater replacement in residential basement due to active leak from existing unit. Inspected current gray cylindrical water heater with galvanized and copper supply piping, exhaust venting through ceiling, and yellow-handled shut-off valve. Documented significant rust-colored staining and water damage on concrete block wall around pipe penetration, indicating chronic leakage. Photographed existing plumbing configuration including three vertical pipes, metallic elbow joint connection to flue pipe, and deteriorated pipe penetration point with visible mineral deposits and corrosion on metal components. Provided replacement options and recommendations for new water heater installation.

Completed annual cooling maintenance on a 9-year-old Payne air conditioning system. Performed comprehensive tune-up including inspection of condenser unit, verification of refrigerant levels, cleaning of coils, testing of electrical components, and assessment of overall system operation. Unit is functioning properly with normal wear consistent with age; documented equipment condition with photographs for service records.

Completed annual cooling maintenance on EnergiAir system under warranty agreement. Performed comprehensive inspection of HVAC equipment including control module, condensate drainage system with PVC piping and drain lines, and refrigerant line connections in basement utility area. All components photographed and documented, system operating within normal parameters with proper drainage function confirmed.

Completed annual cooling maintenance on 9-year-old Trane system. Performed comprehensive tune-up including filter inspection, refrigerant level check, electrical connection testing, condensate drain system evaluation, and overall system performance verification. Unit operating within normal parameters with condensate pump and drainage system functioning properly.

Responded to no-cool call on newly installed AC unit. Upon arrival, inspected indoor air handler and verified proper power supply to inverter control board with green LED indicator illuminated. Confirmed all low-voltage wiring connections were secure at terminal strip, including sensor and equipment communication wires. Checked wireless thermostat interface showing connected status with active power LED. Verified supply and return ductwork connections were properly sealed and airflow pathway was unobstructed through louvered grille assembly. System successfully commissioned and cooling operation restored.

# Condensate Drain Issue Resolution Responded to complaint of condensate dripping and water damage concerns. Upon inspection, discovered excessive moisture accumulation on copper refrigerant lines and significant frost buildup on suction line insulation, indicating potential airflow restriction or refrigerant charge issues. Examined condensate drainage system including primary drain line routing and humidifier installation. Verified proper drain pan condition and drainage pathways. Documented equipment conditions including Aprilaire humidifier integration with ductwork system and associated plumbing connections. Provided assessment findings and recommendations for resolving water intrusion issues.

Installed new shutoff valve on copper water supply line in basement to provide dedicated water source for refrigerator icemaker. Accessed existing cold water distribution piping beneath first floor joists, cut into copper line, and installed compression-style shutoff valve with quarter-inch outlet for icemaker connection. Routed flexible water supply line from new valve location through floor structure to refrigerator location in adjacent laundry/utility area, securing line to floor joists with appropriate strapping to prevent sagging or damage. Tested valve operation and checked for leaks at all connection points to ensure proper installation and water flow to appliance.