Heating, Cooling, Plumbing, and Electrical Services in Ada

Responded to service call for well tank experiencing low pressure that continues to drop. Performed diagnostic inspection of the well pressure system and documented tank conditions with thermal imaging to assess system performance and identify potential pressure loss issues.

Responded to service call for low water pressure issue on a 9-year-old Bryant water heater. Inspected unit, plumbing connections, and shutoff valve assembly; documented existing installation conditions with photos for service records. Customer was unavailable for early arrival, service completed after lunch break.

Completed annual cooling maintenance on 2014 Lennox air conditioning system (18 years old). Performed standard tune-up procedures including system inspection, cleaning, and operational testing. Documentation photos captured for service records.

Responded to sump pump concern running frequently every 5-10 minutes due to recent heavy rainfall. Inspected 8-year-old sump pump system in basement pit, examining pump mechanism, float assembly, discharge piping, and electrical connections. Verified pump operation, checked for proper cycling, and assessed overall system functionality to ensure adequate water removal capacity during high-volume conditions.

Completed annual cooling maintenance on 15-year-old Bryant air conditioning system. Performed comprehensive tune-up including inspection of outdoor condensing unit and evaporator coil assembly, verified all components operating within normal parameters, and documented equipment condition with photographic records showing clean coil fins and properly maintained exterior unit.

Responded to no heat call on 7-year-old furnace with non-functional power switch following previous unsuccessful service visit. Upon inspection, identified faulty control module preventing system operation. Replaced defective module, verified all wire connections, tested system operation, and confirmed furnace restored to normal heating function.

Completed comprehensive assessment for full-home conversion from liquid propane to natural gas in preparation for new utility gas line installation at 30-year-old residential property. Evaluated existing LP appliances, gas piping infrastructure, and venting systems throughout home. Documented current gas regulator location behind exterior access panel and photographed basement utility area showing exposed framing, insulation, and existing ductwork routing to determine optimal natural gas line pathways and conversion requirements for all gas-burning equipment.

Conducted site assessment for whole-home Generac generator installation at residential property. Evaluated existing electrical infrastructure including two main service panels mounted in basement utility area. Documented current electrical configuration with dual panel setup featuring dedicated generator disconnect switch already labeled "GEN" and main breaker panel with multiple circuits. Assessed available space and clearances in basement area for potential generator transfer switch installation. Reviewed electrical service capacity and panel condition to determine compatibility with automatic standby generator system. Photographed electrical panels, service disconnect, existing conduit pathways, and surrounding utility area to document installation requirements and identify any potential obstacles. Evaluated access points for natural gas or propane fuel line connection and exhaust venting requirements. Determined optimal placement for exterior generator pad and unit positioning rela

Completed annual heating and cooling maintenance on EnergiAir system with furnace and air conditioning tune-up. Performed comprehensive inspection of all components, verified proper equipment leveling, checked refrigerant lines and condensate drainage, inspected blower assembly and electrical connections, and confirmed secure mounting of all system components. All equipment found operating within manufacturer specifications with no issues identified during routine maintenance visit.

Responded to no heat call on 10-year-old Carrier furnace that failed to operate following previous service appointment. Upon arrival, found unit unresponsive with home temperature dropping. Inspection revealed inducer motor failure, preventing furnace from initiating heating cycle. Motor showed signs of mechanical wear and electrical connection issues. Replaced defective inducer motor assembly, reconnected all electrical wiring to proper terminals, and verified secure mounting to housing. Tested unit through complete heating cycle, confirmed proper ignition sequence, burner operation, and blower function. Restored heat to home and verified system operating within normal parameters.

Responded to water pressure complaint following recent repair work. Inspected whole-house water treatment system including dual blue filter housings, water softener tank, and pressure tank. Identified potential restriction in filtration system causing reduced flow. Evaluated filter cartridges for blockage, checked valve positions, and verified proper system operation. Documented existing equipment condition and configuration with photos for service records.

Responded to follow-up call for excessive water pressure causing pipe vibration after previous low pressure service. Found failed pressure reducing valve (PRV) allowing incoming municipal pressure to pass through unregulated. Replaced defective 75 PSI rated pressure reducing valve with new unit. Adjusted outlet pressure to proper operating range per manufacturer specifications. Verified pressure gauge reading and tested system operation. Confirmed elimination of water hammer and pipe shaking. Restored normal water pressure throughout property and advised homeowner that system is operating safely.

Completed annual heating maintenance visit on furnace and humidifier system. Performed comprehensive tune-up including filter inspection, burner assembly cleaning, and safety control verification. Discovered significant rust corrosion on humidifier mounting bracket and water reservoir base, indicating prolonged moisture exposure. Removed and replaced deteriorated humidifier orifice plates which showed heavy oxidation and mineral buildup that would have restricted proper water flow and humidification performance. Cleaned corroded mounting surfaces, verified all electrical connections including proper grounding, and tested humidifier operation. System restored to proper working condition with improved humidification capacity for the heating season.

Completed full installation of new HVAC furnace system with integrated Aprilaire humidifier and Bradford White 50-gallon natural gas water heater (Model RG1PV5086N19, 40,000 BTU input). Installation included proper ductwork connection, metallic supply and return ducting, insulated flex duct routing, condensate drainage system with PVC piping, and copper water supply lines. All equipment installed to manufacturer specifications with proper clearances, gas pressure settings verified, and system tested for safe operation.

Responded to water leak at hot water heater with pooling observed around unit base for three days. Upon inspection, identified leaking brass ball valve with compromised gasket seal at connection point. Water heater remained operational throughout incident. Documented valve condition with photography showing turquoise rubber gasket deterioration at threaded connection. Leak isolated to valve assembly on aging system in service since 1990.

Corrected building code violations identified during mechanical inspection. Replaced non-compliant cellular core PVC vent pipe on furnace exhaust side with proper venting materials per manufacturer installation specifications and M1401.1-2015 MRC requirements. Sealed all joints in newly installed trunk line ductwork and return air drop to meet air sealing standards per M1601.4.1-2015 MRC, ensuring proper system performance and code compliance.

Completed furnace installation in basement mechanical room, including mounting vertical furnace unit on platform with proper venting and exhaust connections. Installed white PVC piping for condensate drainage and combustion air intake, routing through ceiling joists to exterior. Connected unit to existing ductwork system and verified all electrical connections, ensuring proper clearances and code-compliant installation in unfinished basement space.

# HP-Heating Problem Service Summary Responded to a heating system issue on a 7-year-old EnergiAir heat pump unit. Upon diagnostic inspection of the mechanical system, determined that the circuit board had failed and required replacement. Accessed the equipment in the utility space where the unit is installed alongside the existing HVAC ductwork, copper piping, and associated mechanical components. Documented the equipment location and configuration with photographs showing the heat pump integrated with the galvanized ductwork system, expansion tank, and various copper supply lines. Replaced the defective circuit board with manufacturer-specified replacement part to restore proper system operation. Verified all electrical connections were secure and tested the unit through a complete heating cycle to confirm proper functionality. System returned to normal operation with heat pump responding correctly to thermostat calls.

Responded to recurring shower valve issue where cartridge was causing the same malfunction as previous service call. Accessed valve assembly through existing wall opening in tiled shower enclosure and inspected brass mounting flanges and central valve stem mechanism. Completed no-charge warranty repair to resolve persistent cartridge defect.

Responded to service call regarding white residue on furniture near 12-year-old Bryant humidifier. Inspected humidifier unit and surrounding area to identify source of mineral deposits. Documented conditions with photographs for service records.