HVAC, Plumbing & Generator Services in Plainwell, MI

Completed annual cooling maintenance on 10-year-old Rheem AC system. Performed comprehensive tune-up including inspection of all major components, verified refrigerant levels, cleaned condenser coils, checked electrical connections, tested thermostat operation, and confirmed proper system cycling. Documented equipment condition with photos of furnace and basement mechanical area showing proper installation and venting configuration. All systems operating within manufacturer specifications with no issues identified.

Completed annual cooling system maintenance and inspection on EnergiAir unit under 2-year preventative maintenance agreement. Performed standard tune-up procedures including filter inspection, refrigerant level verification, electrical connection testing, condensate drain evaluation, and overall system performance assessment. Unit operational and photographs documented for service records.

Conducted on-site evaluation for new Generac generator installation at 45-year-old single-family residence. Assessed existing electrical service configuration, including meter location, electrical panels, and available mounting space on exterior wall with blue-gray vertical siding. Documented current utility setup featuring digital electric meter, junction boxes, and conduit routing to determine optimal generator placement and transfer switch installation requirements. Photographed electrical infrastructure and potential installation area to develop comprehensive estimate for whole-home standby generator system.

Responded to a toilet leak originating from an aftermarket bidet attachment installed on the water supply line. Inspected the bidet unit's connection points, water supply hose, and mounting hardware to identify the source of the leak. Tightened supply line connections and verified proper seal at all attachment points to resolve the issue and restore normal operation.

Completed annual cooling maintenance on Lennox AC system with approximately 5 years of service. Performed comprehensive tune-up including system inspection, component testing, and preventive maintenance procedures to ensure optimal cooling performance for the upcoming season.

Responded to inspection correction notice requiring protective coating on exposed gas piping outside building envelope. Applied corrosion-resistant paint to all exposed black iron pipe sections on exterior installations, including gas meter connections and standby generator supply lines, to comply with MRC G2414.8, IFGC 403.8, MRC G2415.11, IFGC 404.11, MRC G2415.11.2, and IFGC 404.11.2 requirements for pipes in corroding conditions.

Completed annual cooling maintenance on 2021 Goodman air conditioning system. Performed comprehensive tune-up including inspection of outdoor condenser unit, refrigerant lines, and electrical connections. All components found operating within normal parameters with no issues identified during this preventative maintenance visit.

Responded to no-cooling call for 25-year-old residential outdoor HVAC unit that failed to operate. Upon arrival, found condenser unit completely inoperative with extensive rust and corrosion throughout the fan guard assembly and top plate. Inspected heavily weathered condenser fan motor assembly, protective cage, and mounting components showing significant oxidation from prolonged environmental exposure. Unit's advanced age and deteriorated condition indicated end of serviceable life, requiring full system replacement to restore cooling functionality.

Completed comprehensive ASTU-AC Super Tune-up on a 20-year-old American Standard air conditioning system. Performed full system inspection, cleaned condenser coils, checked refrigerant levels and pressures, tested electrical connections, verified proper airflow, inspected condensate pump operation, and confirmed all safety controls functioning properly. System operating within manufacturer specifications with no immediate repairs needed.

Completed annual cooling maintenance on a 2018 Comfortmaker air conditioning system. Performed comprehensive AC tune-up including inspection of outdoor condensing unit, refrigerant lines, and indoor components. Unit placement confirmed acceptable per AMS standards. Customer was notified of and acknowledged later arrival time for service appointment.

Completed annual cooling maintenance on 26-year-old Goodman air conditioning system with condenser model year 2020. Performed comprehensive tune-up including inspection of outdoor unit, verified proper operation of all components, checked refrigerant levels, cleaned condenser coils, and confirmed electrical connections at disconnect box. Unit operating within normal parameters with no immediate service needs identified.

Responded to no hot water call where pilot light was out on Rheem water heater. Previous plumber had incorrectly diagnosed issue as ventilation problem and advised keeping door open, which did not resolve the condition. Performed diagnostic evaluation of water heater pilot assembly, thermocouple, and gas valve operation. Identified actual failure point preventing pilot from staying lit. Completed necessary repairs to restore hot water function and verified proper pilot ignition and burner operation upon completion.

Completed electrical outlet and surge protection work involving junction box wiring in ceiling. Properly terminated and secured multiple circuit conductors using approved wire connectors, ensuring all connections met code requirements for safe operation.

Completed full air conditioning system replacement at residential property. Removed existing outdoor condensing unit and installed new high-efficiency AC condenser on concrete pad with proper refrigerant line connections and electrical disconnect. Installed new evaporator coil at furnace location in basement, integrated with existing gas furnace system. Ran refrigerant linesets through exterior wall with appropriate insulation and PVC line hide. Connected condensate drainage lines with proper pitch and termination. Installed new thermostat wiring and verified all electrical connections meet code requirements. Pressure tested refrigerant lines for leaks, evacuated system to proper vacuum levels, and charged unit to manufacturer specifications. Verified proper airflow across evaporator coil and through ductwork. Started system and confirmed cooling operation, checked temperature split across coil, and monitored system pressures during operation. Reviewed thermostat operation and system c

Completed annual cooling maintenance on Carrier system with warranty through May 2027. Performed comprehensive tune-up including inspection of refrigerant lines, electrical connections, and mechanical components in confined equipment area. System operating within normal parameters with no deficiencies noted at time of service.

Completed annual cooling system tune-up and preventative maintenance on residential AC unit. Performed comprehensive system inspection, cleaned condensate drain line using wet/dry vacuum, checked refrigerant levels, tested electrical connections, and verified proper airflow through evaporator coil. All components operating within manufacturer specifications; system ready for cooling season.

# NC-No Cool Service Responded to service call for AC unit tripping breaker at furnace when turned on. Upon inspection, found heavily soiled blower assembly with significant dust and debris accumulation on blower motor and housing. Discovered compromised wiring with frayed and stripped conductors at terminal connections, creating potential short circuit condition. Identified exterior line set with corrugated conduit running through foundation area showing signs of environmental exposure. The breaker tripping was attributed to electrical fault caused by deteriorated wiring and excessive dirt buildup on motor components creating increased amp draw and potential ground fault.

Completed full HVAC system replacement including outdoor condensing unit and indoor air handler/furnace. Installed new dark gray condenser on existing rock pad against exterior wall with proper clearances maintained. Mounted electrical disconnect box and ran refrigerant line sets with appropriate insulation. Interior installation included new furnace unit with integrated ductwork connections, PVC venting system with proper slope and termination, and Aprilaire humidifier mounted to supply plenum. Verified all electrical connections, tested system operation across all modes, confirmed proper refrigerant charge and airflow, and ensured humidity control integration. System commissioned and left in full operational status.

Completed annual cooling maintenance on EnergiAir system under 5-year warranty agreement. Performed comprehensive tune-up including inspection of refrigerant levels, electrical connections, condensate drain system, and all major components. System operating within manufacturer specifications with no issues found; documented equipment condition with photos of utility area and drainage piping.

# NOISE - Noise Problem Resolution Responded to service call for excessive noise from air conditioning system following routine tune-up. Upon inspection, discovered significant accumulation of leaves and debris in outdoor condensing unit. Cleaned condenser coil fins and removed all foreign material from unit interior and surrounding area. Verified proper airflow through heat exchanger and confirmed all electrical connections secure. Tested system operation and confirmed noise issue resolved with normal operating sound levels restored.