Top-Notch HVAC, Plumbing & Generator Services in Rockford, MI

Performed a tune-up on a 4-year-old Infiniti wall-mounted tankless water heater, including a descaling flush of the heat exchanger, cleaning of the inlet water filter, and inspection of the venting, gas and water connections, and control panel operation. Verified proper combustion and operation, with no leaks, rust, or damage observed on the unit or piping.

Responded to a no-heat call on a 20-year-old basement-located furnace blowing only cold air, and evaluated the system for replacement at the customer's request. Performed a Manual J-style heating and cooling load calculation, accounting for duct supply and return runs, glazing, wall and ceiling areas, and infiltration, yielding a total heating load of approximately 72,583 BTU/h and a total cooling load of approximately 30,696 BTU/h to support proper equipment sizing for the replacement estimate.

Performed annual heating inspection and electrical testing with a clamp meter on a 10-year-old unit. Inspected the condensate drain pan, which showed heavy staining, mineral and biological buildup, and standing water consistent with the customer's reported excess humidity. Cleaned the pan with a wire brush to remove residue and restore proper drainage.

Performed annual heating maintenance on the Navien boiler as part of the recurring two-year tune-up program, including a full system inspection and performance check. Scheduled the next cooling maintenance tune-up for the upcoming season.

Repaired the leaking 1/2" hot water copper line adjacent to the new 3/4" press-fit tie-in at the water heater, restoring a leak-free connection. Verified the exterior 2" PVC intake and exhaust piping is properly secured and glued in place, completing the interior corrections following the previously completed exterior repairs.

Responded to complaint of high humidity levels and excessive energy consumption on 6-year-old LUX system. Customer reported meter readings indicating system was pulling more air than necessary. Upon inspection, utilized borescope camera to investigate ductwork and internal system components. Inspection revealed significant rust and corrosion throughout metal ductwork and plenum areas, with heavy oxidation on galvanized surfaces that could compromise system efficiency and contribute to increased runtime and energy usage. Documented interior conditions with inspection camera for customer review and future reference.

Reworked copper supply lines for lavatory faucet by accessing plumbing through drywall behind fixtures. Installed two new hot and cold shut-off valves with corresponding supply lines to properly serve the faucet. Replaced worn shower cartridge to restore proper temperature control and water flow.

Successfully completed furnace installation in basement utility area. New furnace unit was installed on platform with proper ductwork connections, including vertical supply and return air ducts integrated with existing HVAC infrastructure. All PVC venting pipes were properly routed through ceiling joists with appropriate hangers and supports, ensuring code-compliant exhaust and intake air pathways for high-efficiency operation.

Responded to no-heat complaint on EnergiAir furnace that failed to operate following recent tune-up service. Upon inspection, found unit would not initiate heating cycle. Examined blower assembly, heat exchanger, and internal components for mechanical issues or obstructions. Verified all connections, tested control sequences, and restored unit to proper operation.

Successfully installed a Bradford White 40-gallon natural gas water heater, model RG2V40S6N, in residential utility closet. Unit was positioned on wooden platform with black drain pan for secondary protection. Connected all supply and discharge plumbing including copper piping with brass fittings and yellow-handled isolation valves for serviceability. Installed hot and cold water connections with proper flow direction indicators. Configured gas supply line and verified all connections for leak-free operation. Installed venting system with dark ductwork extending vertically from unit top to ensure proper combustion exhaust. Insulated hot water lines with black foam insulation to minimize heat loss. Connected electrical components and verified proper operation of thermostat controls. All plumbing connections, gas lines, and electrical wiring installed per manufacturer specifications and local code requirements. System tested and confirmed operational.

Responded to upstairs bathroom sink plumbing issue involving disconnected hot water supply line and leaking cold water supply line. Upon inspection, found corroded metal supply lines with deteriorated shut-off valves and compromised flexible connector lines beneath sink cabinet. Reconnected hot water supply line to faucet inlet and repaired cold water line leak by replacing damaged flexible supply hose and securing all connections. Tested both hot and cold water flow, verified proper operation of shut-off valves, and confirmed no active leaks at supply connections or drain assembly.

Responded to service call for reported water heater leak. Upon arrival, conducted thorough inspection of 10-year-old water heater unit and surrounding plumbing connections. Assessed unit condition to determine whether repair or replacement would be most appropriate solution. Documented equipment condition and gas service connections with photos for customer reference and decision-making purposes.

# No Heat Service Call - Goodman Furnace Responded to no heat call for 21-year-old Goodman furnace system. Upon arrival, performed complete system diagnostic to identify cause of heating failure. Inspected furnace unit, air handler, electrical connections, and refrigerant lines. Documented equipment condition and installation setup with photographic evidence showing Goodman-branded furnace with vertical ductwork, associated air handler unit with copper refrigerant piping, and mechanical room layout. Completed troubleshooting procedures and restored heat to residence. System returned to normal operation following service intervention.

Responded to a plumbing leak issue involving a bathtub with water infiltration causing ceiling damage in the space below. Conducted thorough inspection of the tub surround, fixtures, and drain assembly to identify the source of the leak. Documented existing conditions with photographs showing the bathroom layout, bathtub installation, tile work, and surrounding areas for service records and potential follow-up repairs.

Responded to no hot water complaint on 4-year-old electric tank water heater. Upon arrival, inspected electrical panel and water heater junction box. Found discoloration and signs of overheating at wire connections in junction box, indicating poor electrical contact causing unit failure. Verified circuit breaker operation at main panel. Documented electrical components and connection conditions with photos for service records.

Completed annual heating maintenance on furnace and humidifier system. Performed comprehensive tune-up including filter inspection, burner analysis, and safety control verification. System operational with no deficiencies noted; unit continues to perform within manufacturer specifications under existing warranty coverage through November 2027.

Responded to service call for Bradford White tank water heater approximately 3 years old experiencing banging noises. Upon arrival, inspected water heater and surrounding plumbing system. Examined copper supply lines and connections, noting corrosion and mineral deposits at various joints and fittings. Identified sediment accumulation in tank as primary cause of banging sounds during heating cycles. Assessed plumbing connections showing oxidation and verdigris buildup, indicating age-related deterioration. Documented existing conditions through photographs for service records. Advised customer on recommended maintenance procedures and potential future service needs based on current system condition.

Completed on-site estimate for natural gas line installation from main house supply to proposed outdoor kitchen location. Assessed existing gas infrastructure, photographed current gas meter and line configuration, evaluated routing options for new gas line run, and determined materials and labor requirements for safe code-compliant installation.

Responded to no heat call and performed system diagnostics. Upon inspection, found blower motor assembly and electrical control components intact with proper wire connections and secure wire nuts. Verified all electrical connections including ground wires were properly terminated and control module was functioning correctly. System restored to normal heating operation.

Responded to service call for leaking shower in upstairs second bathroom. Upon inspection, identified worn gasket at connection point between handheld showerhead and flexible hose causing water leak. Removed handheld showerhead assembly from wall-mounted bracket holder and inspected black rubber seal at hose connection point, confirming deterioration and improper seal. Replaced defective gasket, reassembled handheld showerhead to flexible hose, and tested unit for proper operation. Verified no leaks present at connection point and confirmed adequate water flow and spray pattern. System restored to full working condition.