Top-Rated HVAC & Plumbing Services in Spring Lake, MI

Conducted comprehensive assessment of 15-year-old furnace and air conditioning system for replacement estimate. Both units currently operational but customer pursuing proactive replacement due to equipment age to prevent potential system failures. Documented existing HVAC installation including furnace with galvanized ductwork, air handling components, and associated electrical and gas line connections in basement utility area. Photographed current system configuration, exposed plumbing infrastructure, PVC drainage lines, copper wiring, and structural mounting to provide detailed reference for replacement planning. Provided equipment replacement options and recommendations based on current system specifications and customer's preventative maintenance objectives.

Responded to service call for furnace blower fan that would not shut off. Upon arrival, accessed the HVAC unit and inspected the control board and associated wiring connections. Examined the integrated circuit board mounted in the control panel, checking all terminal connections and wire harness integrity. Verified proper connections at the terminal blocks where multiple control wires (thermostat wiring, fan control, and power connections) interface with the main PCB. Inspected the relay components and capacitors on the control board for signs of failure or damage. Tested the control board functionality and confirmed the fan relay was remaining energized due to a faulty circuit board. Replaced the defective control board with new unit, reconnected all wiring to proper terminals following manufacturer specifications, and secured the board in the control panel. Restored power to the system and cycled the thermostat through multiple heating calls to verify proper fan operation. Confirmed

Completed full air conditioning system replacement at residential property. Removed existing outdoor condensing unit and installed new olive green condenser on existing concrete pad against exterior wall. Connected refrigerant lines and electrical conduit through vinyl siding to interior components. Mounted electrical disconnect box on exterior wall per code requirements. Verified all connections, tested system operation, and confirmed proper cooling performance upon startup.

Installed condensate drain tube on Bradford White water heater at no charge to address calcification issues caused by condensation from previously extended venting line. The installation was completed as a courtesy follow-up to resolve moisture-related problems that developed after the initial water heater installation and vent modification work.

Complete air conditioning system replacement performed. Removed existing outdoor condensing unit and installed new heat pump system on concrete pad with decorative rock landscaping. Connected refrigerant lines with proper insulation, installed brass service valves, and performed system charging and diagnostics using manifold gauges. Mounted electrical disconnect box on exterior wall, ran electrical wiring and PVC condensate lines from building to new unit. System tested, verified proper operation, and left in full working condition.

Completed full air conditioning system installation at residential property. Installed new outdoor condenser unit on concrete pad in side yard, positioned between house and fence with proper clearance for airflow and serviceability. Connected electrical service via conduit and disconnect box mounted to exterior wall, ensuring code-compliant wiring and proper grounding. Unit commissioned and tested for proper operation, refrigerant charge verified, and all safety controls confirmed functional.

Completed estimate for air conditioning system at residential property. Documented existing HVAC equipment including Lennox Pulse furnace with PVC venting and metal cabinet air handler unit in basement utility area. Photographed current system configuration and equipment conditions to provide accurate assessment for AC replacement or upgrade options.

Completed IAQ-MISC service call for personal use equipment documentation in residential basement mechanical area. Performed comprehensive photographic documentation of existing HVAC system installation, including Carrier furnace unit, galvanized sheet metal supply plenum, and associated ductwork distribution system. All equipment photographed in current operational condition with no service modifications or adjustments performed during this visit.

Completed kitchen drain rework for single basin sink configuration with new garbage disposal installation. Reconfigured drain tubular assembly, installed disposal unit with proper mounting flange and hardware, and connected white PVC P-trap to discharge outlet ensuring proper drainage flow and code-compliant installation.

Completed estimate for 25-year-old air conditioning system that has been inoperative since previous cooling season. Performed visual inspection of existing HVAC equipment in basement mechanical room, including furnace unit, ductwork system, and associated components. Documented current system configuration with photographs showing furnace installation, sheet metal plenum and duct connections, refrigerant line routing, condensate drainage, and electrical connections. Assessed overall condition of aging equipment and provided replacement options for non-functional air conditioning system.

Completed annual cooling system maintenance on 7-year-old Goodman unit as part of preventive maintenance membership. Performed standard tune-up procedures including inspection of condensate pump with drainage system, verified proper operation of all components, and confirmed system is operating within manufacturer specifications. Unit found in good working condition with no immediate service needs identified.

Completed annual cooling maintenance on 30-year-old York air conditioning system. Performed comprehensive tune-up including inspection of all major components, verified refrigerant levels, cleaned condenser coils, checked electrical connections, and tested system operation to ensure optimal performance for the cooling season.

Performed diagnostic evaluation on non-operational residential air conditioning system for club member. Identified failed evaporator coil requiring replacement. Provided comprehensive estimate for system replacement options given the extent of repairs needed. Documented existing HVAC installation including furnace, air handler, ductwork configuration, and mechanical room conditions with detailed photography for customer review and decision-making purposes.

Responded to no cooling complaint on residential AC unit. Upon inspection, found contactor heavily contaminated with spider webs and debris causing failure to energize compressor. Cleaned contactor assembly, removed all cobwebs and buildup from electrical connections, verified proper voltage at unit, and tested system operation. Unit now cooling properly with contactor engaging as designed.

Completed annual cooling maintenance on 13-year-old residential air conditioning system. Performed comprehensive tune-up including inspection of condenser unit, electrical connections, capacitor, and contactor assembly. All components tested and found operating within normal parameters for continued system performance.

Cut access opening in drywall to reach existing dryer vent system. Removed old dryer vent ducting and installed new flexible aluminum duct, connecting it to the existing wall penetration. Installed white access panel to cover drywall opening for future serviceability.

Completed comprehensive ASTU-AC Super Tune-up on residential air conditioning system. Inspected and photographed condensate pump assembly and drainage system in utility space, confirming proper operation of white condensate pump unit with associated PVC piping, drain pan, and electrical connections. All components functioning within normal parameters with no immediate service concerns identified.

Successfully completed full furnace installation in basement utility area. Installed new furnace unit on concrete pad with proper positioning and leveling. Connected vertical supply ductwork with metal banding and secured all duct transitions to existing system. Integrated air handler component with proper sealing at all seams. Ran and secured refrigerant lines and associated piping, including proper labeling and support throughout vertical runs. Completed all electrical connections using appropriate conduit. System tested and verified operational upon completion.

Completed annual cooling maintenance on a 7-year-old EcoAir system with a 2019 condenser model. Inspected the Nature's Home Quantum 25A BASIC LED III control box mounted in the utility area, verified proper electrical connections and power supply functionality. Examined interior ductwork components, noting normal operational dust accumulation on metal surfaces and confirmed damper mechanism rods were intact and functioning properly.

Completed project estimate for installation of new dryer venting system for upstairs laundry area. Assessment included evaluation of existing laundry room configuration with dryer unit and determination of optimal routing for compliant exhaust vent run to exterior, ensuring proper ventilation for safe and efficient dryer operation.