HVAC, Plumbing & Generator Services in West Olive, MI

Completed annual heating maintenance on 6-year-old Goodman furnace system with humidifier. Performed comprehensive tune-up including filter inspection, burner assembly cleaning, heat exchanger examination, blower motor lubrication, and thermostat calibration. Verified proper operation of humidifier unit and checked all safety controls. System operating within manufacturer specifications with no issues found.

Completed site evaluation for new residential standby generator installation. Assessed existing electrical service panel in basement utility area, documenting 200-amp main breaker configuration with adequate capacity for generator integration. Panel features modern circuit breaker arrangement with organized Romex wiring distribution through ceiling joists. Evaluated exterior utility meter locations on foundation wall, confirming placement of electric meter and gas meter for proper load calculations and fuel source considerations. Documented access requirements including property gate code 0120 for future installation coordination. Photographed electrical infrastructure and exterior utility connections to prepare comprehensive installation estimate for homeowner new to generator systems. Site conditions favorable for standard automatic transfer switch installation and generator pad placement near existing utility services.

Responded to backup issue affecting basement drains while main house plumbing remained functional. Upon arrival, located utility area containing water treatment equipment, pressure tank, and washing machine with floor drain and sump pit access. Inspected basement drainage system including floor drain assembly and sump pump pit visible in utility space. Identified blockage isolated to basement drainage line preventing proper flow when fixtures were in use. Cleared obstruction from basement drain line using appropriate drain cleaning equipment, restoring full drainage capacity to affected fixtures. Tested system by running water through basement drains while other household plumbing was in operation, confirming proper flow with no backup occurring. Verified sump pump pit and associated drainage components functioning correctly. System restored to normal operation with all basement drains flowing freely.

Conducted site evaluation for tankless water heater replacement estimate on 13-year-old Bradford White unit. Documented existing gas meter specifications (AC-250, MAOP 5 PSI, 250 CFH capacity) and utility connection points, photographed basement mechanical room layout and available installation space for equipment sizing and placement recommendations.

Completed annual heating maintenance on furnace with humidifier system. Performed standard tune-up procedures including filter inspection, burner assembly cleaning, and safety control verification. Documented excessive standing water with debris accumulation in humidifier drain pan, indicating potential drainage issue or overflow condition requiring monitoring.

Successfully installed a 20KW Kohler standby generator with 200A service at residential property. Coordinated utility disconnect and reconnect services, completed gas pressure testing per inspector requirements, and obtained all necessary electrical and mechanical permits. Installation included proper gas line connections to existing natural gas meter assembly, electrical integration with main service panel, and final inspections approved by local building department.

Completed installation of a 50-gallon natural gas power vent water heater in basement utility area. Unit was properly positioned, vented with approved PVC piping, and connected to existing gas supply line. Electrical connections were made to dedicated circuit with proper grounding, control panel tested and calibrated with temperature settings adjusted to optimal range. All plumbing connections secured, system pressurized and leak-tested, then unit fired and verified for proper operation with green status indicator confirming successful ignition and heating cycle.

Conducted water heater replacement estimate for a 21-year-old residential unit located in basement utility area. Inspected existing water heater installation, including copper supply piping, circulation pump assembly, electrical connections, and PVC drainage system mounted to ceiling joists. Documented current equipment configuration and utility connections to provide replacement recommendations for aging system.

Completed furnace super tune-ups on two systems: a 10-year-old Carrier unit and a 30-year-old Lennox unit. During inspection, identified deteriorated PVC venting with visible gaps and discoloration on intake/exhaust piping that may require future attention. Performed standard maintenance procedures including filter inspection, blower component cleaning, and system operational testing on both furnaces to ensure proper heating season performance.

Completed annual cooling maintenance on outdoor condensing unit at vacant AirBnB property. Performed standard tune-up procedures including inspection of condenser coils, louvers, and exterior casing, which showed moderate dirt accumulation and weathering consistent with outdoor exposure. Unit operational upon completion of service.

Completed annual cooling system tune-up and preventative maintenance on EnergiAir unit. Performed comprehensive inspection of all system components, verified proper refrigerant levels, cleaned condenser coils, checked electrical connections, and confirmed optimal system operation. Unit is functioning within manufacturer specifications and ready for the cooling season.

Completed annual heating maintenance visit including furnace tune-up and humidifier service per club membership agreement. Inspected heating system components, ductwork, and insulation in attic space, verified proper operation of all equipment, and documented conditions with photos. Customer contacted prior to arrival as requested, accessed property via kitchen slider door, and completed all scheduled maintenance tasks without issues.

Completed full installation of residential HVAC system including new furnace and air conditioning unit in basement mechanical room. Installed dark-colored high-efficiency furnace with proper white PVC venting routed vertically through structure. Mounted gray metal air handler unit adjacent to furnace with metallic supply ductwork connections. Installed system monitoring and control device with operational indicators at base of equipment. Secured all PVC piping with appropriate brackets and straps to ensure code-compliant installation. Verified all electrical connections, tested system operation, and confirmed proper airflow through ductwork. System powered on successfully with all safety controls and monitoring devices functioning as designed.

Conducted on-site evaluation for whole-house generator installation with focus on Kohler generator system. Assessed existing electrical infrastructure including main service panel with dual-row circuit breaker configuration and 240V 3-wire Consumers Energy meter rated at 30TA. Documented current electrical service capacity and panel layout to determine transfer switch placement requirements and load calculation needs for proper generator sizing. Photographed electrical panel interior showing multiple branch circuits and service entrance conductors, as well as exterior utility meter to verify service specifications for integration with automatic transfer switch system.

Completed full air conditioning system replacement including outdoor condenser unit and indoor air handler. New condenser was installed on existing concrete pad with proper clearances maintained from landscaping and structure. Indoor air handler was positioned in basement mechanical room with all ductwork connections properly sealed and secured to existing distribution system.

Completed annual heating maintenance on furnace system. Performed comprehensive tune-up including inspection of all mechanical and electrical components, pressure switches, safety controls, and wiring connections. Verified proper operation of all systems, checked electrical connections at terminal blocks, and inspected blower assembly and ductwork. All components found operating within normal parameters. System is in good working condition with warranty coverage extending through September 2033.

Responded to running toilet complaint in 24-year-old residential property. Upon inspection, identified faulty fill valve causing continuous water flow. Replaced worn fill valve assembly and adjusted float mechanism to proper water level. Tested flush cycle multiple times to confirm proper operation and verify no leakage. Performed water quality testing using standard iron and pH analysis kit to rule out mineral buildup or corrosion issues affecting valve performance. Inspected basement plumbing infrastructure including supply lines and shutoff valves for any additional concerns. Toilet now operating normally with complete shutoff after flush cycle.

Completed annual cooling maintenance on approximately 20-year-old residential air conditioning system. Performed standard tune-up procedures including inspection of outdoor condenser unit, verification of electrical connections and disconnect box, and assessment of refrigerant lines and associated plumbing components. All systems operational with no immediate service needs identified at time of visit.

Completed annual cooling maintenance on Energi WT 7-2034 system per 2-year service agreement. Performed comprehensive system inspection, verified all electrical connections, tested thermostat operation including internal components and sensor mechanisms, and documented equipment condition with photographs. All components found operating within normal parameters.

Completed annual cooling maintenance on 6-year-old EnergiAir unit manufactured in 2023. Inspected condensate drain system, including drain pan and overflow safety switch housing, noting normal wear and minor dirt accumulation on components. All equipment photographed and operating within normal parameters upon completion of tune-up procedures.