Reputable HVAC, Plumbing & Generator Services in Zeeland, MI

Completed annual cooling system tune-up and maintenance on 5-year-old air conditioning unit, including inspection of all components, ductwork, and connections. Performed water heater tune-up on A.O. Smith 40-gallon natural gas unit, verifying proper operation and safety controls. Documented equipment conditions with photographs and noted customer request for complimentary water testing at future appointment.

# CP-Cooling Problem Resolution Responded to service call for 10-year-old York air conditioning system with no cold air coming from interior vents. Upon arrival, performed visual inspection of outdoor condensing unit. Found unit surrounded by excessive vegetation growth, with plants and vines growing against and through ventilation grille openings, significantly restricting airflow to condenser coil. Removed access panel to inspect internal components. Observed accumulated dirt, debris, and organic matter on internal surfaces and components. Checked electrical connections at capacitor and compressor. Inspected refrigerant lines and condenser coil condition. Coil appeared darkened with debris accumulation, further reducing heat transfer efficiency. Cleared vegetation from around unit perimeter to restore proper airflow clearance. Cleaned condenser coil and removed debris from internal compartment. Verified all electrical connections were secure. Cycled system to confirm proper operat

Responded to emergency no-cool call following same-day tune-up where system failed to operate after previous technician departed. Upon arrival, performed diagnostic inspection of outdoor unit and discovered blown fuse in control circuit. Replaced defective fuse with proper replacement, restoring power to control board and enabling normal system operation. Verified all electrical connections, tested system startup sequence, and confirmed unit cooling properly before departure.

# CP-Cooling Problem - Bryant System Responded to service call for approximately 20-year-old Bryant split system with inadequate cooling performance. Upon inspection, discovered severely corroded evaporator coil with extensive rust throughout the interior components, indicating long-term moisture exposure and deterioration. The refrigerant lines and mounting brackets showed significant oxidation, compromising system integrity and heat transfer efficiency. Documented conditions with photos showing the extent of corrosion on the evaporator assembly and overall system configuration with air handler mounted above the Bryant furnace. Advised customer that the extensive rust damage to the evaporator coil and associated components has severely degraded cooling capacity and system performance, requiring coil replacement or full system replacement to restore proper operation.

Conducted comprehensive plumbing assessment for toilet repair requirements in residential bathroom. Documented existing conditions including toilet fixture, water supply connections, cabinet accessibility, and structural elements in ceiling area above, identifying necessary scope of work for complete toilet repair and potential rough plumbing modifications.

Responded to service call for bathroom light replacement. Removed existing recessed lighting fixture from drop ceiling grid system and installed new recessed LED light panel in ceiling tile opening. Verified proper electrical connections and tested fixture operation to ensure adequate illumination. Work completed as quoted.

Completed annual cooling system tune-up and preventative maintenance inspection. Verified condensate drain system operation and pump functionality in utility space, confirmed proper drainage into collection pan. Updated best contact number in system records and documented equipment condition with photos per standard maintenance protocol.

Completed annual cooling maintenance inspection on residential HVAC system. Performed comprehensive tune-up including visual inspection of outdoor condensing unit, electrical connections, and wiring terminations. Verified all wire connections at terminal block and capacitor are secure with proper color-coded terminations. Inspected unit mounting on concrete pad with decorative rock landscaping. All electrical components including capacitor, relay assembly, and control wiring found in good working condition. System operating within normal parameters. Unit ready for cooling season.

Conducted site assessment for relocating existing 35-year-old Bryant air conditioning unit from back porch to side of house, requiring approximately 30 feet of relocation distance. Documented current installation conditions including basement electrical infrastructure, circuit panel locations, and existing conduit routing to determine feasibility and scope of equipment relocation project.

Completed full air conditioning system replacement in residential basement utility room. Removed existing AC unit and installed new high-efficiency furnace with proper venting and drainage systems. Connected galvanized metal ductwork with 90-degree elbow joint to air handler unit, ensuring secure connections and proper airflow. Installed black flexible condensate line and white PVC drainage piping for condensate removal. Verified all electrical connections, safety labels, and warning stickers properly affixed to unit. Tested system operation to confirm proper functionality of new equipment.

Completed full residential air conditioning system replacement with installation of new Amana condenser unit on exterior concrete pad. Unit positioned adjacent to building with proper clearances maintained from landscaping and structures. Established all refrigerant line connections, condensate drainage via PVC piping, and electrical service to new outdoor unit. Interior air handler integrated with existing ductwork system, with flexible duct connections secured and all ventilation components properly configured. Verified system startup, refrigerant charge levels, and operational parameters across all equipment. All connections tested and confirmed leak-free with system cycling properly through cooling modes.

Completed full HVAC system installation including new furnace and air conditioning unit. Outdoor condensing unit installed on concrete pad with proper gravel base, refrigerant lines run and insulated along exterior wall, electrical disconnect mounted per code. Indoor furnace installed with all necessary ductwork connections, gas line hookup, and proper venting. All components tested and verified operational upon completion.

Performed air conditioning estimate on non-operational system in residential property with 18-year-old equipment. Documented existing HVAC installation including furnace unit with significant dust accumulation, ductwork configuration, and air handler components in basement utility area. System assessment completed to determine repair or replacement recommendations for customer consideration.

Completed annual cooling maintenance on 18-year-old air conditioning system. Performed comprehensive tune-up including inspection of all components, verified system operation within manufacturer specifications, and documented unit condition as good with continued reliable performance expected.

Responded to service call for toilet leaking water when flushed. Upon arrival, inspected two-piece white porcelain toilet in residential bathroom. Assessed tank components, flush valve assembly, and bowl connections for source of water leak during flush cycle. Documented existing conditions with photographs showing standard toilet installation with closed lid, adjacent toilet paper holder, and wood-grain vinyl flooring. Completed diagnostic evaluation of flush mechanism and water supply connections to identify leak origin and recommend appropriate repairs.

Responded to water leak service call and performed diagnostic inspection of HVAC system. Upon examination, traced moisture intrusion to condensate drainage issue affecting the air handler unit. Inspected internal components including control boards, wiring harnesses, and blower assembly to assess water damage and verify proper system operation. Cleared condensate line obstruction, tested drainage flow, and confirmed all electrical components and connections were dry and functioning correctly with no signs of corrosion or short circuits.

Completed QUOTR-quoted repair by replacing defective blower motor on residential HVAC unit. Unit restored to full operational status with proper airflow confirmed upon testing.

Completed annual cooling maintenance on EnergiAir system with 2-year tune-up inspection. Performed comprehensive evaluation of outdoor condensing unit, verified proper operation of all components, and inspected electrical connections and refrigerant lines. Unit found in good working condition with proper airflow through condenser coil. Documented equipment condition with photos showing outdoor unit installation on concrete pad with proper clearances and landscaping maintenance around unit. All safety labels intact and visible. System operating within normal parameters.

Responded to service call for furnace failing to operate during air conditioning cycle. Upon inspection, found significant dust and debris accumulation on evaporator coil and air handler components, restricting airflow and causing system interlock issues. Accessed control board and verified electrical connections and relay operation. Cleaned evaporator coil fins and ventilation grille, removing built-up contaminants that were impeding proper air circulation. Tested system operation and confirmed furnace blower now functions correctly in coordination with cooling cycle. System restored to normal operation with improved airflow efficiency.

Responded to a clogged floor drain in basement utility area. Upon inspection, removed drain cover and cleared blockage from the drain line using appropriate drain cleaning equipment. Disassembled section of white PVC drain piping to access and remove accumulated debris causing the obstruction. Successfully restored proper drainage flow, reassembled all plumbing components, and tested system to verify complete functionality.