Reputable HVAC, Plumbing & Generator Services in Zeeland, MI

Responded to water leak complaint on Fujitsu mini split system. Upon inspection, found deteriorated foam insulation on refrigerant line set with significant gap allowing condensate accumulation and dark debris buildup around exposed piping. Documented condition of both interior insulated piping and exterior wall penetration where line set passes through siding, noting aged and discolored insulation requiring replacement to prevent continued moisture issues.

Performed comprehensive estimate for non-operational residential air conditioning system with ground-level outdoor condensing unit and basement furnace installation. Documented existing equipment conditions including beige condensing unit positioned on river rock landscaping bed against exterior wall, and basement furnace with multiple insulated ductwork configurations in black and silver wrapping. Assessed system components, photographed equipment placement and mechanical connections, and prepared detailed estimate for repair or replacement options to restore cooling functionality.

Responded to no-cooling call on 9-year-old air conditioning system. Upon arrival, verified thermostat was calling for cooling and electrical panel breakers were in proper position. Diagnosed outdoor condensing unit failure to start. Identified defective dual run capacitor preventing compressor and condenser fan motor operation. Replaced failed capacitor with proper MFD-rated component. System tested and verified operational with normal amperage draws and proper cooling cycle established.

# CP-Cooling Problem Resolution Responded to service call for 27-year-old air conditioning system that failed to start. Upon arrival, performed diagnostic evaluation of outdoor condensing unit located against exterior wall. Unit exhibited signs of age and deferred maintenance, with significant rust corrosion visible on refrigerant lines and weathered components. Vegetation overgrowth around unit base was noted, potentially restricting airflow to condenser. Conducted electrical troubleshooting to identify cause of no-start condition. Inspected disconnect, contactor, capacitor, and control wiring for failures. Verified power supply to unit and tested all electrical components for proper operation. Cleared debris and vegetation from around unit perimeter to restore adequate ventilation clearance. System was successfully restored to operational status. Advised customer of unit's advanced age and deteriorated condition of refrigerant piping, recommending consideration for system replace

# No Cool Service Call - YORK System Responded to no cooling condition affecting entire home on an approximately eleven-year-old YORK air conditioning system. Upon inspection of outdoor condensing unit, found extensive rust and corrosion on metal base pan and interior surfaces, indicating prolonged moisture exposure. Electrical panel showed significant accumulation of dirt, debris, and organic matter including leaves in bottom of cabinet. Multiple wire connections exhibited oxidation and green corrosion patina on terminal blocks. Identified failed dual-run capacitor (40+5 MFD) as primary cause of no cooling condition. Capacitor showed signs of deterioration consistent with age and environmental exposure. Replaced defective capacitor with new OEM-equivalent unit. Cleaned electrical connections and terminals to ensure proper conductivity. Removed accumulated debris from cabinet interior. Verified all wire connections secure and properly terminated. Started system and confirmed compres

Responded to sump pump service call and completed full sump pump replacement per approval. Unit was successfully installed and tested for proper operation. Photographed completed installation showing laundry room area and plumbing access panel with visible water supply lines and valve assembly, confirming all connections are secure and system is functioning as designed.

Completed full HVAC system replacement including indoor furnace unit and outdoor condensing unit. Installed new furnace in basement utility area with proper ventilation using white PVC piping, including elbows and drainage connections. Mounted unit on gray plenum base with all safety labels and specifications clearly visible. Routed black refrigerant lines from indoor unit to outdoor condenser. Installed new outdoor AC condensing unit on concrete pad with proper clearances, connected via gray PVC electrical conduit to wall-mounted disconnect box. Verified all electrical connections, refrigerant line sets, and drainage systems functioning properly. System tested and operational upon completion.

Completed annual cooling maintenance on EnergiAir system installed in 2021. Performed comprehensive tune-up including system inspection, filter assessment, and operational testing. Unit operating within normal parameters with no issues identified during service visit.

Completed annual cooling maintenance on 14-year-old EnergiAir system. Performed standard tune-up procedures including system inspection, cleaning, and operational testing. Documented condensate drain pan condition with photographic evidence showing wear and staining typical of system age.

Completed annual cooling system tune-up and preventative maintenance inspection. Discussed membership benefits with homeowner, who expressed interest in potential enrollment. System photographed and documented for service records.

Completed annual cooling maintenance inspection on residential AC system. Performed standard tune-up procedures including filter check, refrigerant level verification, electrical connections inspection, and condensate drain system evaluation. During inspection, identified rust staining on PVC condensate drain piping near metal mounting bracket, indicating previous moisture exposure or mineral deposits. Verified drain line is flowing properly with no active leaks present. All system components operating within normal parameters at time of service.

Completed full HVAC system replacement including outdoor condensing unit and indoor air handler components. New condenser installed on concrete pad with proper refrigerant line connections, electrical conduit, and drainage configuration. Indoor furnace and humidifier assembly installed in basement utility area with appropriate PVC condensate drainage system and electrical connections verified per manufacturer specifications.

Completed annual cooling maintenance on 15-year-old system. Cleaned condensate drain pan, removed debris and moisture buildup, and performed routine inspection of HVAC components and ductwork to ensure proper system operation for the cooling season.

Installed protective plastic pad underneath existing mini split heat pump stand to prevent damage to concrete mounting surface. Verified unit remained level after pad installation and confirmed stable mounting configuration. No-charge service completed as preventative maintenance measure.

Performed estimate for water heater replacement on existing 10-year-old Whirlpool unit manufactured by U.S. Craftmaster Water Heater Company. Documented current automatic storage water heater condition and specifications, photographed manufacturer data plate showing ANSI Z21.10.1-2013/CSA 4.1-2013 certification, and assessed installation location in basement utility area. Customer seeking replacement options with availability for early installation scheduling.

# NC-No Cool Service Completed Responded to a no cooling call and performed diagnostic inspection of the HVAC system. Upon examination, identified a failed run capacitor as the root cause of the cooling failure. Replaced the defective capacitor with a new unit, verified proper electrical connections at the terminals, and tested system operation. Unit restored to full cooling functionality with all components operating within normal parameters.

Conducted electrical estimate for residential property requiring two new dedicated outlets. Assessed existing electrical panel capacity and circuit availability for relocated air conditioning unit being installed by HVAC contractor. Evaluated electrical requirements for hot tub installation, including load calculations and appropriate circuit sizing. Inspected main breaker panel to determine available spaces and amperage capacity for additional circuits. Photographed existing electrical panel configuration showing current breaker layout and available positions for new circuit installations. Provided technical assessment for installing properly sized circuits with appropriate overcurrent protection to support both appliances per NEC requirements.

Replaced 90-degree bend on refrigerant line connected to piston nut on HVAC system. Removed damaged copper piping section, installed new bend with proper brazing techniques, and verified secure connections at all fittings. System tested and confirmed operational with no refrigerant leaks detected.

Completed annual cooling system maintenance on EnergiAir unit with 2023 commissioning date. Performed comprehensive tune-up including inspection of condensate pump assembly, drain lines, and associated components. All systems operating within normal parameters; documented equipment condition with photos showing condensate pump installation and drain routing.

Completed full HVAC system replacement including new air conditioning condensing unit and indoor air handler components. Removed existing equipment and installed new condensing unit on exterior concrete pad with proper clearance and leveling, positioned against house foundation with white rock bed surround. Mounted electrical disconnect box on exterior wall and ran refrigerant lines and electrical conduit from outdoor unit to indoor installation. In basement mechanical room, installed new furnace and air handler assembly between existing support posts with proper clearance specifications. Connected white PVC condensate drainage piping and configured ductwork connections. Verified all electrical connections, tested refrigerant charge levels, and confirmed proper airflow through system. System commissioned and operational upon completion.