Reputable HVAC, Plumbing & Generator Services in Zeeland, MI

Provided comprehensive estimate for complete HVAC system replacement including 16-year-old furnace and air conditioning unit with confirmed refrigerant leak in evaporator coils, along with aging water heater replacement to prevent future emergency situation. Assessed existing basement installation with current ductwork configuration, humidifier accessory, and copper plumbing connections to determine proper equipment sizing and replacement specifications for all three major mechanical systems.

Responded to service call for malfunctioning kitchen sink hose. Upon inspection, assessed the pull-out spray hose assembly and associated connections beneath the double-basin stainless steel sink. Verified proper operation of chrome shut-off valves, supply lines, and spray attachment. Addressed hose functionality issues and ensured secure connections at faucet assembly and under-sink mounting points. Tested system for proper water flow and confirmed leak-free operation of all components upon completion.

Completed full air conditioning system replacement with installation of new Amana outdoor condensing unit. Unit was properly positioned on concrete pad with appropriate clearances from structure. Refrigerant lines were installed and insulated, electrical disconnect box mounted to exterior wall, and all connections properly secured. System was charged with A2L refrigerant to manufacturer specifications with factory charge of 52 oz and total system charge of 52.4 oz documented on unit labeling. All service valves installed with protective caps, system tested and verified operational with proper airflow through top-mounted fan assembly.

Completed annual cooling system maintenance and inspection as part of 10-year preventative maintenance program. Performed comprehensive tune-up including visual inspection of condensate pump assembly, verified proper operation of mechanical components, and documented equipment condition through photographic records. All system components found to be in functional condition with normal operational wear, no immediate repairs required at this time.

Responded to report of brown/tan water discoloration on basement ceiling below bathroom in 1996-built home, with issue progressively worsening over 4-year period since 2016. Conducted visual inspection of bathroom above affected area, examining toilet, flooring, and surrounding fixtures for signs of active leakage or moisture intrusion. Documented bathroom conditions and basement ceiling staining with photographs showing water damage patterns on textured ceiling and wall surfaces. No active leak observed during inspection; staining indicates historical water intrusion requiring further investigation to determine source, which may include toilet seal failure, supply line issues, or drain pipe concerns.

Completed annual cooling maintenance and 10-year equipment checkout on 2014 cooling system. Performed comprehensive inspection of all components, verified refrigerant levels, cleaned condenser coil, checked electrical connections, tested system operation, and documented equipment condition with photos. All systems operating within manufacturer specifications at time of departure.

Completed installation of ductless mini-split system on exterior of building. Installed outdoor condensing unit with weatherproof electrical disconnect box and dedicated 220V circuit with appropriate breaker protection. Mounted line set with insulated refrigerant lines running through exterior wall penetration, secured flexible metallic ductwork along exterior siding. Verified proper electrical connections, tested system operation, and confirmed all safety controls functioning correctly.

Conducted comprehensive estimate for residential air conditioning system replacement. Documented existing HVAC equipment including basement-mounted furnace with Aprilaire humidifier and associated ductwork, electrical controls, and outdoor condenser unit with refrigerant lines. Assessed current system configuration and provided detailed recommendations for new AC installation to meet customer cooling requirements.

Completed annual AC maintenance and tune-up on residential cooling system. Performed comprehensive inspection of air handler unit and associated components including condensate pump assembly, PVC drain lines, and ductwork connections. Verified proper operation of all mechanical systems, checked electrical connections, and confirmed condensate drainage system functioning correctly. All equipment operating within normal parameters with no issues identified.

Completed annual cooling system tune-up and maintenance on 5-year-old air conditioning unit, including inspection of all components, ductwork, and connections. Performed water heater tune-up on A.O. Smith 40-gallon natural gas unit, verifying proper operation and safety controls. Documented equipment conditions with photographs and noted customer request for complimentary water testing at future appointment.

# CP-Cooling Problem Resolution Responded to service call for 10-year-old York air conditioning system with no cold air coming from interior vents. Upon arrival, performed visual inspection of outdoor condensing unit. Found unit surrounded by excessive vegetation growth, with plants and vines growing against and through ventilation grille openings, significantly restricting airflow to condenser coil. Removed access panel to inspect internal components. Observed accumulated dirt, debris, and organic matter on internal surfaces and components. Checked electrical connections at capacitor and compressor. Inspected refrigerant lines and condenser coil condition. Coil appeared darkened with debris accumulation, further reducing heat transfer efficiency. Cleared vegetation from around unit perimeter to restore proper airflow clearance. Cleaned condenser coil and removed debris from internal compartment. Verified all electrical connections were secure. Cycled system to confirm proper operat

Responded to emergency no-cool call following same-day tune-up where system failed to operate after previous technician departed. Upon arrival, performed diagnostic inspection of outdoor unit and discovered blown fuse in control circuit. Replaced defective fuse with proper replacement, restoring power to control board and enabling normal system operation. Verified all electrical connections, tested system startup sequence, and confirmed unit cooling properly before departure.

# CP-Cooling Problem - Bryant System Responded to service call for approximately 20-year-old Bryant split system with inadequate cooling performance. Upon inspection, discovered severely corroded evaporator coil with extensive rust throughout the interior components, indicating long-term moisture exposure and deterioration. The refrigerant lines and mounting brackets showed significant oxidation, compromising system integrity and heat transfer efficiency. Documented conditions with photos showing the extent of corrosion on the evaporator assembly and overall system configuration with air handler mounted above the Bryant furnace. Advised customer that the extensive rust damage to the evaporator coil and associated components has severely degraded cooling capacity and system performance, requiring coil replacement or full system replacement to restore proper operation.

Conducted comprehensive plumbing assessment for toilet repair requirements in residential bathroom. Documented existing conditions including toilet fixture, water supply connections, cabinet accessibility, and structural elements in ceiling area above, identifying necessary scope of work for complete toilet repair and potential rough plumbing modifications.

Responded to service call for bathroom light replacement. Removed existing recessed lighting fixture from drop ceiling grid system and installed new recessed LED light panel in ceiling tile opening. Verified proper electrical connections and tested fixture operation to ensure adequate illumination. Work completed as quoted.

Completed annual cooling system tune-up and preventative maintenance inspection. Verified condensate drain system operation and pump functionality in utility space, confirmed proper drainage into collection pan. Updated best contact number in system records and documented equipment condition with photos per standard maintenance protocol.

Completed annual cooling maintenance inspection on residential HVAC system. Performed comprehensive tune-up including visual inspection of outdoor condensing unit, electrical connections, and wiring terminations. Verified all wire connections at terminal block and capacitor are secure with proper color-coded terminations. Inspected unit mounting on concrete pad with decorative rock landscaping. All electrical components including capacitor, relay assembly, and control wiring found in good working condition. System operating within normal parameters. Unit ready for cooling season.

Conducted site assessment for relocating existing 35-year-old Bryant air conditioning unit from back porch to side of house, requiring approximately 30 feet of relocation distance. Documented current installation conditions including basement electrical infrastructure, circuit panel locations, and existing conduit routing to determine feasibility and scope of equipment relocation project.

Completed full air conditioning system replacement in residential basement utility room. Removed existing AC unit and installed new high-efficiency furnace with proper venting and drainage systems. Connected galvanized metal ductwork with 90-degree elbow joint to air handler unit, ensuring secure connections and proper airflow. Installed black flexible condensate line and white PVC drainage piping for condensate removal. Verified all electrical connections, safety labels, and warning stickers properly affixed to unit. Tested system operation to confirm proper functionality of new equipment.

Completed full residential air conditioning system replacement with installation of new Amana condenser unit on exterior concrete pad. Unit positioned adjacent to building with proper clearances maintained from landscaping and structures. Established all refrigerant line connections, condensate drainage via PVC piping, and electrical service to new outdoor unit. Interior air handler integrated with existing ductwork system, with flexible duct connections secured and all ventilation components properly configured. Verified system startup, refrigerant charge levels, and operational parameters across all equipment. All connections tested and confirmed leak-free with system cycling properly through cooling modes.