Reputable HVAC, Plumbing & Generator Services in Zeeland, MI

Responded to service call for gas line evaluation and quote preparation. Inspected existing gas piping system in basement area, identifying sections of galvanized pipe requiring assessment for potential replacement. Documented current installation configuration including pipe routing along ceiling joists and connections to mechanical equipment. Photographed existing gas line components, pipe materials, and accessibility conditions to support accurate quote development for gas line modification or replacement work.

# AC No Cooling - 16 Year Old Amana System Responded to service call for air conditioning system not cooling properly. Upon arrival, inspected 16-year-old Amana outdoor condensing unit located on exterior of residence. **Inspection Findings:** - Outdoor unit accessible with electrical disconnect and refrigerant lines properly installed - Significant deterioration observed inside electrical compartment - Extensive rust staining, dirt accumulation, and debris buildup throughout interior housing - Capacitor and wiring connections inspected - multiple colored wire terminals present on cylindrical capacitor - Evidence of moisture intrusion and environmental exposure causing interior component degradation **Work Performed:** - Performed visual inspection of outdoor condensing unit - Opened electrical compartment to assess internal components - Documented condition of capacitor, wiring, and interior housing - Photographed equipment condition for service records - Assessed overall system de

Responded to emergency call for burst pipe in basement caused by winter freeze conditions. Upon arrival, assessed damage and located the failed section of copper supply line. Cut out damaged pipe segment and prepared clean ends for repair. Installed new copper pipe section with brass compression fittings to restore water supply integrity. Cut access panel in interior wall to reach affected plumbing. Tested system for leaks and proper water pressure. Shut off exterior hose bib to prevent future freeze damage. All repairs completed successfully with no active leaks detected.

Completed annual cooling system tune-up and preventative maintenance on 9-year-old air conditioning unit. Performed standard inspection protocols, utilized refrigerant recovery equipment for system diagnostics, and verified proper operation of all components. System found to be functioning within normal parameters with no immediate service concerns identified.

Completed combined furnace and water heater estimate for property in flood zone. Inspected 29-year-old Bradford White water heater and existing HVAC furnace system, verified sump pump operation to ensure proper functionality in case of water heater failure. Provided quotes for both equipment replacement and repair options, including recommendation for installation of drain pan under water heater for flood protection.

Completed installation of a 40-gallon tall natural gas water heater manufactured by Bradford White Corporation in basement utility area. Unit was properly positioned, connected to existing copper supply lines with brass fittings and valves, and vented through metallic exhaust vent pipe in accordance with manufacturer specifications and local code requirements.

Responded to service call for leaking water heater over 20 years old. Upon arrival, inspected residential water heater located in basement utility area adjacent to furnace system. Identified active leak at plumbing connections and assessed overall condition of unit. Documented equipment age and deterioration through photographic documentation showing water heater installation, surrounding HVAC equipment, and mechanical room configuration. Due to advanced age of unit exceeding typical service life expectancy, recommended replacement rather than repair. Customer opted for cash/check without warranty coverage.

Completed full HVAC system replacement including outdoor condensing unit and indoor air handler/furnace assembly. Installed new condenser on existing concrete pad against exterior wall with proper clearances maintained. Mounted unit features horizontal louver grille design with manufacturer specifications clearly labeled. Interior installation includes new furnace unit with dual vertical metallic supply and return ductwork, properly insulated with reflective foil wrap and secured with metallic tape. Connected black flexible insulated ductwork to distribution system. Installed condensate drain pan at base of unit. Verified all copper refrigerant lines properly connected and insulated. Ensured electrical connections secure at outdoor unit. System tested and operating within manufacturer specifications.

Completed annual cooling system tune-up and preventative maintenance on 15-year-old air conditioning unit. Inspected condensate drain pan and added algae prevention tablets to prevent biological growth and ensure proper drainage throughout the cooling season. Performed standard maintenance procedures including system performance evaluation and documentation with photographic records.

Completed sales estimate for aging residential HVAC system installed in basement utility room. Documented existing air handler unit with associated ductwork, including vertical metal supply ducts with foil-taped connections, flexible ductwork, and refrigerant lines. System shows significant age with visible wear on components and ductwork connections. Photographed current installation configuration including plenum assembly, copper refrigerant piping, and mechanical room layout to provide comprehensive assessment for equipment replacement recommendations.

Responded to main bathroom for leaking faucet repair. Upon inspection, identified leak at traditional two-handle chrome faucet with porcelain handle inserts on white oval sink. Disassembled faucet handles, replaced worn cartridges and seals, reassembled unit, and tested both hot and cold water lines to confirm leak was eliminated and proper operation restored.

Completed annual cooling system maintenance on a 15-year-old AC unit, including full system inspection, electrical component testing, and verification of capacitor and Comfort Alert monitoring device connections. All wiring connections were inspected and found secure, system operational parameters were within manufacturer specifications, and photographic documentation was captured for service records.

Conducted sales estimate for replacement of 30-year-old residential forced air furnace system currently operational in utility closet. Documented existing beige furnace unit with galvanized metal ductwork, adjacent water heater, and overall mechanical room configuration through photographic assessment to provide comprehensive replacement proposal for aging HVAC equipment.

Conducted on-site assessment for whole home re-pipe project. Documented existing plumbing infrastructure including corroded water heater connections with visible mineral deposits on metal fittings, braided stainless steel supply lines, and PVC drainage system running through exposed ceiling joists in basement/crawl space area. Photographed current conditions to support comprehensive estimate for complete residential plumbing system replacement.

Responded to service call for home experiencing inconsistent heating and cooling performance requiring frequent thermostat adjustments. Upon inspection, found improperly configured thermostat wiring at the wall unit with multiple wire connections requiring verification at the terminal block. Removed thermostat cover to access RC, RH, Y, G, and C terminal connections and traced wiring back to the air handler control board. Inspected the main control board PCB with LED indicators and verified proper voltage at all connection terminals. Examined wire bundle routing between thermostat and HVAC system components, including connections to capacitors and refrigerant line assembly. Corrected thermostat wiring configuration to ensure proper communication between control systems. Verified all terminal connections were secure at both the wall unit and control board. Cycled system through heating and cooling modes to confirm proper operation and stable temperature control without requiring manual

Conducted site assessment and provided project estimate for potential sump pump replacement in eleven-year-old residential property. Inspected existing submersible sump pump system with PVC discharge piping in basement area, noting water staining on concrete floor and functional pump assembly within basin. Documented current system condition and exterior discharge configuration for quote preparation, with no immediate operational issues identified at time of inspection.

Completed comprehensive AC Super Tune-up on 6-year-old system, including full inspection of refrigerant lines, electrical connections, and condensate drainage components. All mechanical and plumbing connections verified to be secure and functioning properly, with system operating within manufacturer specifications. Customer renewed annual maintenance club membership at time of service.

Completed toilet installation in residential bathroom with teal walls and beige vinyl flooring. White toilet successfully installed beneath window, with all connections secured and tested for proper operation and leak-free performance.

Serviced existing sump pump system in basement utility area. Inspected vertical PVC discharge pipe assembly secured to concrete block wall with proper mounting straps, verified electrical connection at wall-mounted outlet box, and confirmed operational status of pump within concrete pit. System found functioning properly with discharge piping, check valve, and drainage components in good working condition.

Responded to service call for 13-year-old water heater that would not maintain heating operation. Upon inspection, diagnosed failed thermocouple or gas control valve preventing pilot from staying lit. Performed necessary repairs to restore proper heating function and verified unit operation before completing service.