Heating, Cooling, Plumbing, and Electrical Services in Ada

Completed annual AC tune-up on 13-year-old EnergiAir system (2016 condenser model). Inspected air handler unit and found drain pan with heavy mineral deposits, mold buildup, and corrosion requiring cleaning or replacement recommendation. Examined outdoor condenser unit electrical components, noting rust and weathering on enclosure with aged capacitor and loosely organized wiring connections. All refrigerant lines, electrical connections, and system operations checked and documented with photos for customer records.

Completed annual cooling maintenance and 6-year equipment checkout on residential air conditioning system. Performed comprehensive inspection of electrical components including contactor, capacitor (60/5μF dual-run rated at 440V AC), and control wiring connections. All electrical connections were verified secure, capacitor tested within acceptable parameters, and contactor operation confirmed normal. System operational and ready for cooling season.

Completed comprehensive plumbing project estimate for bathroom remodel involving exposed copper piping installation within framed wall cavity with spray foam insulation, and assessment of existing shower enclosure featuring dark bronze framed glass sliding doors with white acrylic surround. Documented all plumbing infrastructure, wall framing conditions, and finished bathroom fixtures to provide accurate scope and specifications for proposed renovation work.

Completed full air conditioning system replacement in basement mechanical room. Removed existing AC unit and installed new condensing unit with proper refrigerant line connections. Verified furnace integration with new AC system, ensuring all ductwork connections were properly sealed and secured. Installed new PVC condensate drainage lines and tested system operation. All electrical connections completed to code, system commissioned and tested for proper cooling operation and airflow throughout the residence.

Completed installation of Aprilaire manual humidifier on residential forced-air furnace system. Unit was mounted to supply plenum with proper ductwork connections established, condensate drainage configured via PVC piping, and all electrical connections completed. System was tested and verified operational upon completion.

Completed annual cooling maintenance on 2016 Carrier AC system. Performed comprehensive tune-up including system inspection, refrigerant pressure check, electrical connections verification, and condenser coil cleaning. All components operating within manufacturer specifications, and system is ready for the cooling season.

Completed annual cooling maintenance on AC system. Performed comprehensive tune-up inspection including checking refrigerant levels, electrical connections, and condensate drainage system. Inspected outdoor unit and confirmed no manufacturer's label cover exists for this model as these components are not standard equipment for this unit type. Photographed condensate pump assembly and drainage pan showing normal operational condition with minor debris accumulation around base. All systems tested and operating within manufacturer specifications.

Completed annual cooling maintenance on 2015 EnergiAir system with warranty coverage extending through June 2026. Performed comprehensive tune-up including inspection of condensate drainage system, refrigerant lines, and indoor air handler unit located in utility space. All components found operating within normal parameters and system prepared for cooling season.

Replaced residential well pressure tank system. Installed new blue pressure tank with proper plumbing connections including copper piping and flexible conduit. Verified system operation and confirmed proper air pressure at 38.0 PSI using digital gauge at tank valve.

Completed annual cooling maintenance on 2015 Carrier HVAC system with 7 years of service history. Performed comprehensive inspection of furnace unit, ductwork, humidifier connections, and condensate drainage system; all components found operating within normal parameters with no deficiencies noted. System cleaned, tested, and left in proper working condition.

Responded to no-water issue at kitchen faucets following recent water service restoration. Accessed crawl space to inspect supply lines and verified proper water flow through main distribution system, including PEX and PVC supply lines. Restored full water pressure and functionality to kitchen sink faucets, including main gooseneck fixture and auxiliary filtration faucet, by addressing air lock in supply lines after municipal water turn-on.

Responded to report of toilet leaking at base with water penetrating through floor to level below. Upon inspection, identified compromised wax ring seal between toilet base and closet flange. Removed toilet, scraped old wax ring, inspected flange for damage, and installed new wax ring seal. Reset toilet with proper alignment, tightened closet bolts to manufacturer specifications, and tested for leaks. Verified water-tight seal at base and confirmed no further leakage to lower floor.

Successfully installed a 40-gallon natural gas Bradford White water heater in basement utility area. Connected all copper supply lines, gas piping, and exhaust venting to manufacturer specifications, ensuring proper clearances and code compliance. Unit was tested for proper operation, with all safety features verified and system commissioned for immediate use.

Conducted on-site assessment of existing well pressure tank system for estimate revision. Documented current installation including pressure tank with associated piping, valves, pressure gauge, and control components. Photographed complete system setup showing tank mounted on base, PVC supply lines with shutoff valves, pressure switch assembly, and connections to water distribution system. Verified all equipment specifications and configuration details necessary for preparing updated estimate documentation.

Rebuilt water inlet line assembly using white PVC piping with brass valves and fittings. Installation included multiple elbows, connections, and adapters to ensure proper water flow and system functionality. Work completed in utility room with all components securely mounted and tested.

Completed annual cooling maintenance and inspected system per warranty concern regarding compressor not cycling off properly. Evaluated contactor operation, verified electrical connections at terminal blocks, and documented control panel wiring configuration with photos showing all power and control circuits functioning within specifications.

Performed comprehensive assessment of non-functioning water heater in basement utility area. Documented existing white cylindrical water heater with connected copper piping, brass fittings, and shut-off valves showing signs of age and wear. Evaluated plumbing infrastructure including horizontal copper supply lines, elbow joint configurations, and overall system condition in deteriorated mechanical room environment. Provided estimate for water heater replacement and necessary plumbing modifications.

Responded to toilet flushing issue that had persisted for approximately one week. Removed tank lid and inspected internal flush mechanism, including Fluidmaster fill valve with float assembly and flush valve with flapper system. Adjusted components and verified proper water flow and tank refill operation to restore normal flushing function.

Responded to electrical issue where basement light switch was affecting microwave outlet and wall receptacle used for vacuuming. Troubleshot circuit to identify improper wiring connection causing multiple devices to be affected by single switch. Inspected and photographed electrical connections, identified discolored terminals indicating poor contact and potential arcing at affected outlet. Corrected wiring configuration to isolate switch from unintended receptacles, ensuring microwave and wall outlet now operate independently of basement lighting circuit.

Completed annual GEO tune-up on 2015 Bard geothermal system with warranty through March 2031. Performed comprehensive system inspection, verified proper operation of ground loop components and PVC piping with brass fittings and valves, and documented equipment condition with photos. System operating within normal parameters with no humidifier present per customer preference.