Top-Notch HVAC, Plumbing & Generator Services in Battle Creek, MI

Responded to service call for water heater not heating properly and pilot light failing to remain lit. Upon arrival, inspected 20+ year old residential gas water heater installed in basement utility area. Unit exhibited classic symptoms of thermocouple failure and potential gas valve issues common in aging equipment. Evaluated all connections, venting system, and safety components. Discussed replacement options with customer given the age and condition of the existing unit. Customer enrolled in maintenance program for ongoing service protection. Documented equipment condition with photographs for reference.

Completed full HVAC system replacement including installation of new Carrier furnace in basement utility area and outdoor condenser unit. Furnace installed on concrete pad with vertical supply ductwork connected and integrated with existing distribution system. Outdoor condensing unit positioned on concrete pad against building exterior with proper electrical connections, disconnect box, and conduit routing to service panel. All ductwork connections secured, electrical wiring completed per code requirements, and system tested for proper operation. Payment collected per authorization.

Successfully completed add-on air conditioning system installation to existing forced-air heating system. Installed new outdoor condensing unit on concrete pad adjacent to building exterior with proper electrical disconnect and conduit routing through exterior wall. Connected refrigerant lines and integrated new evaporator coil with existing furnace and ductwork in basement mechanical room. Installed PVC condensate drain lines and completed all necessary refrigerant piping connections between indoor and outdoor components. Verified proper airflow through existing duct system, tested electrical connections at disconnect box, and confirmed system operation. All work performed per manufacturer specifications and local code requirements.

Responded to no-heat call for gas furnace in basement installation. Upon arrival, found furnace with open access panel and non-functional ignition system. Performed diagnostic inspection of burner assembly, control board, and ignition components to identify failure point preventing unit from firing. Completed necessary repairs to restore heating operation and verified proper ignition sequence and flame establishment before closing up unit and returning system to normal service.

Responded to no heat call on 21-year-old Nordyne furnace. Found flame sensor had detached from mounting bracket due to frayed and broken wire connection, causing system failure. This flame sensor has required multiple previous replacements due to environmental conditions affecting component longevity. Documented failed component condition with photos showing deteriorated wiring and displaced sensor rod. Customer advised that recurring failures are attributed to environmental factors within the system.

Completed annual cooling system tune-up and preventative maintenance inspection. Performed standard AC maintenance procedures including system performance evaluation, component inspection, and operational testing. All equipment found operating within normal parameters and system ready for cooling season.

Completed annual heating and cooling maintenance tune-up on furnace, air conditioning system, and humidifier under recurring service agreement. Performed comprehensive system inspection and cleaning. During furnace inspection, discovered significant accumulation of fibrous debris and insulation material inside blower housing compartment, along with dirt and grime buildup on interior surfaces. Removed and cleaned contaminated blower housing component. Inspected inducer motor assembly and circular intake opening with rubber gasket seal, noting wear and discoloration around opening. Verified proper operation of pressure switch and sensing devices. Cleaned all accessible components, checked electrical connections, and ensured proper airflow throughout system. System operational upon completion.

Completed annual heating and cooling maintenance on Amana furnace and air conditioning system. Performed comprehensive tune-up including inspection of all major components, filter replacement, and system testing. Observed evidence of previous condensate drainage issues near air handler with water staining on platform surface; drain pan currently functioning properly with no active leakage detected at time of service.

Completed installation of a Bradford White 40-gallon natural gas water heater, model RG240S6N, rated at 40,000 BTU/hr. Connected all copper supply and discharge piping with proper shut-off valves and pressure relief components. Installed unit in basement utility area against foundation wall with adequate clearance per manufacturer specifications. Verified proper gas manifold pressure settings and natural draft venting requirements per ANSI compliance standards. All connections insulated and secured, unit tested and operational.

Responded to service call for non-operational water heater in basement utility area. Upon arrival, inspected 10-year-old Rheem water heater and associated plumbing connections. Diagnosed issue, performed necessary repairs to restore hot water functionality, and verified proper operation of unit before completing service.

Completed annual cooling maintenance on HVAC system under EnergiAir warranty coverage. Performed comprehensive inspection of air handler unit, gas line connections, condensate pump assembly, and ductwork components in basement mechanical room. All equipment operating within normal parameters; documented existing installation conditions with photographic records for warranty file maintenance.

Responded to report of small fire or smoke incident at electrical panel connected to newly installed AC unit in sixty-year-old residence. Upon arrival, inspected main electrical panel and surrounding area for signs of overheating, arcing, or fire damage. Removed panel cover to conduct thorough internal inspection of circuit breakers, bus bars, and all wire connections. Examined all incoming service conductors and branch circuit wiring for heat damage, discoloration, or compromised insulation. Verified proper torque on all breaker connections and main lugs. Inspected grounding and bonding connections for integrity. Checked for any signs of moisture intrusion, corrosion, or loose connections that may have contributed to the incident. Photographed panel interior showing dual rows of circuit breakers, main service conductors, and overall wiring configuration for documentation purposes. Verified no active fire hazards or immediate safety concerns present within the electrical panel at time

Responded to no hot water condition on recently installed Bradford White water heater. Upon arrival, inspected unit and verified pilot light was not lit. Successfully ignited pilot light and confirmed burner operation. Verified proper function of circulation pump and hydronic system components. Unit restored to full operation with hot water delivery confirmed.

Responded to electrical service call for multiple fixture issues and surge protection evaluation. Inspected vanity light fixtures, ceiling fan operation, and malfunctioning light switch as requested. Documented existing electrical meter installation and exterior service panel configuration. Meter displayed proper utility connection with digital interval recording capabilities and standard residential service specifications. External electrical components showed typical weathering consistent with outdoor exposure. Assessed overall electrical system condition and provided recommendations for fixture replacements and whole-house surge protection options to enhance electrical safety and system reliability.

Responded to service call for unidentified noise coming from 6-year-old Lennox furnace. Upon arrival, reviewed customer-provided video of the noise to assist with diagnosis. Conducted thorough inspection of furnace system and air distribution components. Discovered significant debris accumulation consisting of dried plant matter, twigs, and organic material lodged in exterior vent opening. Interior floor register also showed dust buildup. Removed all debris from exterior duct opening and cleaned affected areas. Inspected furnace blower assembly, motor bearings, and belt for mechanical issues that could contribute to noise. Verified proper airflow through system after clearing obstructions. Cycled furnace through multiple heating cycles to confirm noise was eliminated. System operating normally with no abnormal sounds detected upon completion. Advised customer to monitor for any recurring issues.

Completed installation of 40-gallon natural gas water heater with 6-year warranty and short configuration in basement utility area. Unit was properly vented with metal flue pipe, connected to existing copper supply lines with brass fittings, and integrated with expansion tank system. All connections were tested and verified operational alongside existing HVAC equipment.

Completed installation of 50-gallon natural gas water heater with expansion tank and sediment filter as specified. Unit was properly positioned, vented with appropriate exhaust ductwork, and connected to existing copper water lines and gas supply, with all connections tested and verified operational upon completion.

Responded to water leak concern involving 8-year-old Rheem 40-gallon natural gas water heater (Model PROH40S-3AN RH62, manufactured 07/2017) in 50-year-old home. Conducted thorough inspection of unit and surrounding area to identify source of water spreading across floor. Documented equipment condition, venting system, and installation configuration with photographs for diagnostic purposes and customer records.

Completed annual cooling maintenance on 37-year-old outdoor condensing unit. Performed comprehensive tune-up including inspection of electrical disconnect, refrigerant lines, and condenser coil; cleared accumulated leaf debris from around unit perimeter; verified proper operation of all components and system functionality.

Completed routine preventive maintenance on 20-year-old residential Generac generator. Performed comprehensive system inspection including visual examination of all major components, electrical connections, and mechanical assemblies. Replaced engine oil filter with OEM Generac filter and replenished engine oil to proper level in reservoir. Inspected coolant system, refrigerant lines, and all hose connections for signs of wear or leakage—all found secure and in satisfactory condition. Verified integrity of electrical components, control panel labels, and safety warning indicators. Examined compressor assembly, accumulator, and associated copper refrigerant lines for proper installation and condition. Confirmed all mounting hardware, brackets, and clamps properly secured. Unit access panel insulation intact with no damage noted. System showing normal wear consistent with age but operating within acceptable parameters with no immediate performance concerns identified. Generator ready for