Top-Notch HVAC, Plumbing & Generator Services in Battle Creek, MI

Completed annual cooling system tune-up and inspection on aging HVAC unit over 10 years old. Inspected condensate pump operation and drainage system, verified proper function with both discharge lines connected and green indicator light operational. Observed active condensation removal from evaporator coil with moisture present on collection cylinder, confirming system is cooling effectively and condensate management equipment is working as designed.

Responded to service call for salt mistakenly added to water heater instead of water softener unit. Salt failed to dissolve, resulting in water discoloration and odor issues. Assessed system contamination, documented conditions with photos, and provided customer education on proper water softener maintenance and distinction between water heater and water softener systems to prevent future occurrences.

Completed comprehensive plumbing system repair on water heater installation with focus on pressure regulation and valve assembly replacement. Addressed deteriorated flexible connector hoses and corroded copper piping connections, installed new brass ball valves and pressure gauge assembly to restore proper system monitoring and flow control. Remediated moisture damage area and ensured all connections were properly sealed to prevent future water intrusion and corrosion issues.

Completed annual cooling system tune-up on 20-year-old Haier unit with condenser model year 2022. Performed standard maintenance inspection, documented equipment installation and electrical connections including grounding wires and power supply components in basement utility area. All systems operating within normal parameters upon completion.

Completed kitchen faucet installation, replacing the existing fixture with a new chrome single-handle model with pull-out spray attachment. Addressed gas line concern by removing saddle clamp from 3-foot section of gas piping in the ceiling cavity, ensuring proper gas line integrity and code compliance. Verified all plumbing connections for leaks, tested faucet operation and water flow in both basins, and confirmed proper drainage function.

Responded to complaint of gurgling tub drain when toilet flushed and strong acidic odor in 60-year-old home with septic system. Accessed plumbing system through basement/crawlspace to inspect drain and vent piping. Upon investigation, identified venting issue in drain-waste-vent system causing negative pressure when toilet discharged, resulting in gurgling at tub drain and allowing sewer gases to escape into living space. Documented existing plumbing configuration with photos showing copper drain lines, vent pipes, and connection points between fixtures to assess proper venting and drainage flow for this single-bathroom home on septic system.

Completed installation of a 40-gallon Bradford White natural gas atmospheric vent water heater in basement location. Unit was properly positioned on metallic base plate, with all copper supply and discharge piping connected per manufacturer specifications and local code requirements. Gas line connection, temperature and pressure relief valve, and venting system were installed and tested for proper operation and safety compliance.

Removed existing gas line and successfully rerouted new gas line for outdoor grill installation. Work was performed in basement/crawl space area, routing new copper gas line along ceiling joists to exterior location. Installation included proper mounting hardware, shutoff valve, and compliance with gas line code requirements for outdoor appliance connection.

Successfully completed full HVAC system replacement including new Carrier furnace and outdoor condensing unit. Installed furnace in basement mechanical room with complete ductwork assembly, including metallic supply plenum and curved elbow transitions. Mounted new white cylindrical AC condenser on existing concrete pad against exterior wall with proper refrigerant line routing through wall penetration and secure electrical connections via exterior junction box. All components tested and operational upon completion.

Completed scheduled 10-year maintenance tune-up on Kohler generator unit. Performed comprehensive inspection of all major components, including engine, electrical systems, and control panels. Serviced air filter assembly, checked oil levels, inspected battery connections, and verified proper operation of all safety systems. All components found to be functioning within normal parameters. Unit tested and left in full operational condition.

Responded to customer request for electrical panel evaluation due to fire hazard concerns. Conducted thorough inspection of aging residential circuit breaker panel mounted in wooden wall frame. Panel exhibited signs of wear consistent with older electrical installation, including surface discoloration and dust accumulation on beige metal enclosure. Assessed wiring configuration including multiple copper cables, white insulated wires, and colored conductors entering from top and bottom of panel. Examined circuit breaker arrangement in two vertical columns with older style black and tan switches. Documented condition of main disconnect components, wire connections with twist-on connectors, and flexible metal conduit. Photographed panel installation and surrounding wooden framing for estimate preparation. Provided assessment findings and recommendations for necessary repairs or panel replacement to address potential safety concerns.

Responded to no hot water condition affecting entire residence. Upon inspection, found 11-year-old AO Smith water heater in basement utility area with significant dust accumulation and age-related wear. Unit located in unfinished basement space with proper venting through existing flue system connected to horizontal ductwork. Documented existing installation showing cylindrical tank-style heater with metallic flue pipe, red-handled valve connection, and manufacturer specification plate. Assessed basement infrastructure including concrete block walls, exposed floor joists, and concrete flooring suitable for replacement installation. Provided estimate for water heater replacement due to unit failure and age exceeding typical service life expectancy.

Completed full HVAC system installation including Lennox furnace unit in basement utility area and outdoor condensing unit. Connected all PVC venting, refrigerant lines, ductwork, and electrical components per manufacturer specifications. Properly charged system with refrigerant, documented field charge levels, verified all safety labels and warnings in place, and confirmed operational performance of complete heating and cooling system.

Responded to a drain problem in a 30-40 year old residential property where pipe replacement was required. Upon inspection, accessed the affected area through exposed floor joists and subflooring, revealing deteriorated wooden structural members with visible water damage, staining, and discoloration consistent with prolonged moisture exposure from the failing drain line. Documented extensive damage to ceiling framing and support beams, including evidence of previous water infiltration that had compromised the structural integrity of multiple joists. Photographed the existing conditions showing damaged lumber, metal joist hangers, and the routing of existing plumbing and electrical systems through the floor structure to provide comprehensive documentation for the necessary pipe replacement and potential structural repairs.

Completed annual cooling maintenance on 13-year-old York AC system and performed hot water heater tune-up. Inspected condensate pump assembly in crawl space, verified proper operation and electrical connections, checked all mechanical components for wear and functionality. All systems tested and operating within normal parameters.

Completed annual cooling maintenance on 16-year-old Payne air conditioning system. Performed comprehensive tune-up including inspection of condensate pump assembly, verified proper drainage operation, and documented equipment condition with photos. All components operating within normal parameters at time of service.

# NC-No Cool Service Completed Responded to no cooling call with furnace fan operating but outdoor unit buzzing without compressor engagement. Upon inspection, found outdoor condenser unit experiencing electrical failure preventing compressor startup. Accessed outdoor unit and identified failed dual-run capacitor showing visible signs of deterioration, corrosion, and age-related failure. Capacitor tested out of specification and unable to provide necessary starting voltage to compressor motor, resulting in characteristic buzzing sound without rotation. Removed defective capacitor and installed new dual-run capacitor with proper microfarad ratings for both compressor and condenser fan motor. Secured all electrical connections, verified proper wire routing, and ensured terminals were tight. Energized system and confirmed compressor started smoothly without buzzing. Verified condenser fan motor operation and proper amperage draw on both compressor and fan motor. Monitored system through

Responded to complaint of loud noise from AC unit that began after thermostat replacement. Upon inspection, identified faulty contactor causing excessive noise during operation. Replaced defective contactor with new unit, verified all electrical connections, and tested system operation to confirm noise was eliminated and unit returned to normal heating function.

Responded to call regarding strong septic odor in residence. Conducted thorough inspection of utility area and basement plumbing infrastructure. Examined washing machine drain connections, PVC drainage system, and water treatment equipment for potential sources of sewer gas infiltration. Inspected overhead plumbing including drain lines and vent pipes for proper configuration and potential trap seal failures. Photographed existing conditions including utility room plumbing configuration and basement ceiling infrastructure showing drain and vent pipe routing. No immediate plumbing failures or leaks identified during visual inspection. Advised client on potential causes of septic odors including dry trap seals, compromised vent stack, or issues with septic system itself requiring further specialized evaluation.

Responded to service call for air conditioning system experiencing intermittent operation and complete failure during hot weather conditions. Upon arrival, found system had been manually restarted by customer and was currently running. Performed comprehensive diagnostic inspection of indoor air handler and outdoor condensing unit. Inspected blower motor assembly, gas valve connections, electrical wiring, and capacitor for signs of failure or degradation. Found significant accumulation of dirt, dust, and debris on outdoor unit components and electrical connections, indicating lack of recent maintenance. Documented existing conditions with photographs showing interior cabinet components, wiring connections, and outdoor unit electrical assembly with visible contamination. System components showed normal operational wear with environmental exposure evident throughout. Evaluated blower motor operation, capacitor condition, and electrical connections for proper function and safety concerns.