Completed full water heater installation in residential utility space with exposed wall framing. Installed new cylindrical water heater unit with proper venting through metallic exhaust pipe, connected copper supply lines and integrated with existing PVC drainage system. All plumbing connections secured, unit tested and verified operational.

Completed full HVAC system installation including indoor furnace/air handler unit and outdoor Amana condensing unit. Installed furnace in basement utility area with proper ductwork connections, PVC condensate drainage system, and electrical conduit. Mounted outdoor condenser on concrete pad against exterior wall with appropriate clearances, connected refrigerant lines, installed electrical service disconnect, and completed PVC drainage piping through exterior wall. System tested and verified operational upon completion.

Performed complimentary indoor air quality assessment and documentation of existing HVAC ductwork installation in attic and basement areas. Inspected metallic ductwork runs, joint sealing integrity, and overall system configuration including 90-degree elbows and straight sections with foil tape applications. Photographed exposed mechanical systems for estimate preparation and future reference regarding potential duct sealing, insulation improvements, or air quality enhancement recommendations.

Completed annual cooling maintenance on 14-year-old Luxaire air conditioning system. Performed standard tune-up procedures including system inspection, condensate pump verification, and drainage line assessment. Unit operating within normal parameters with condensate removal system functioning properly.

Responded to no cooling call on 12-year-old York system. Upon inspection, diagnosed leaking evaporator coil in indoor air handler unit located in basement mechanical room and confirmed outdoor condenser unit operational status. Documented equipment condition with photos of both outdoor condensing unit positioned on decorative rock bed against residence and indoor air handler cabinet with associated refrigerant piping and drainage lines. Provided estimate for evaporator coil replacement and related repairs necessary to restore system functionality.

# NC-No Cool Service Completed Responded to no cooling complaint with outdoor unit running and thermostat set to 76°F but reading 78°F. Upon inspection, discovered extensive corrosion and rust throughout the refrigerant line connections and valve assembly. Copper piping exhibited significant oxidation with green patina formation, and connection points showed heavy corrosion buildup indicating prolonged moisture exposure. The evaporator coil displayed discoloration and oxidation across multiple copper tube loops. Metal mounting surfaces and galvanized brackets exhibited severe rust deterioration with mineral deposits and scaling. The advanced corrosion at pipe joints and valve assembly compromised system integrity and refrigerant flow. Documented equipment condition with photos showing deteriorated copper lines, corroded coil sections, and rusted connection hardware. System requires immediate attention to address corrosion-related refrigerant leaks and component failure to restore prop

# Water Heater Repair - Lukewarm Water Issue Responded to service call for water heater producing only lukewarm water. Upon arrival, inspected residential tank-style water heater with DEFENDER Safety System in basement utility area. Unit showed no visible leaks, unusual noises, or error codes displayed. Performed diagnostic evaluation of heating system components. Checked thermostat settings and verified both upper and lower heating elements for proper operation. Tested temperature-pressure relief valve functionality and inspected all copper supply line connections for proper flow. Examined gas supply line (if gas unit) or electrical connections (if electric unit) for adequate delivery to heating components. Identified heating element malfunction as primary cause of inadequate water temperature. Lower heating element showed signs of failure, preventing tank from maintaining proper temperature throughout full capacity. Upper element functioning but insufficient to heat entire tank vo

Completed annual cooling maintenance on 9-year-old Lennox system. Performed comprehensive tune-up including inspection of condensate drain system with ball valves and PVC piping, verified proper drainage function, and documented equipment condition with photos. Confirmed best contact number and system operational status.

Completed annual heating maintenance on 19-year-old Goodman furnace and humidifier system. Performed comprehensive tune-up including visual inspection, component testing, and system diagnostics. Utilized borescope inspection camera to examine internal ductwork, heat exchanger surfaces, and ventilation components for signs of deterioration, blockages, or moisture accumulation. System operational upon completion of scheduled maintenance.

Completed annual cooling system tune-up and preventative maintenance on 2013 EnergiAir unit with warranty valid through February 2027. Performed standard inspection procedures, checked refrigerant levels, cleaned condenser coils, verified electrical connections, and tested system operation to ensure optimal performance for the cooling season. All components functioning within normal parameters; unit operating efficiently with no issues identified.

Responded to plumbing leak in basement utility/furnace room that had been ongoing for two weeks. Upon arrival, found significant water accumulation on concrete floor with standing water and multiple puddles throughout the space. Located source of leak in copper piping system suspended from floor joists. Removed and replaced failed section of copper pipe, including associated fittings and mounting brackets. Tested system under pressure to verify repair integrity and confirm no additional leaks present. Cleaned up standing water and verified proper drainage. System restored to full operational status with no further water intrusion detected.

Completed full HVAC system installation including Carrier brand furnace, air conditioning condenser unit, and water heater. Installed furnace in basement/utility room with proper plenum connections, air filtration system, condensate drain lines via white PVC piping, electrical conduit, and flexible ductwork connections. Mounted outdoor AC condenser unit on concrete pad with appropriate electrical disconnect box and conduit routing to exterior wall. All equipment properly vented, connected to ductwork distribution system, and tested for operation. System installation meets manufacturer specifications and local code requirements.

Completed annual cooling system maintenance and inspection on EnergiAir unit with warranty coverage through July 2033. Performed comprehensive tune-up including filter inspection, refrigerant level check, electrical component testing, condensate drain evaluation, and system performance verification. Documented equipment condition with photos showing condensate management system and mechanical room setup, with drip pan positioned to collect drainage beneath unit.

Responded to service call for 11-year-old Bradford White water heater with extinguished pilot light. Upon arrival, inspected unit and surrounding utility area, documented existing conditions including ductwork, plumbing connections, and water heater installation. Successfully diagnosed pilot light issue, relit pilot assembly, and verified proper ignition and burner operation to restore hot water service.

Completed annual cooling maintenance on 2021 EnergiAir system under warranty through 12-2028. Performed comprehensive tune-up including inspection of evaporator coil, condensate drain system with visible water accumulation in drain pan, and verified proper operation of Aprilaire humidifier control. All mechanical components, refrigerant lines, and electrical connections inspected and found operational.

Responded to no-cooling call on 5-year-old Ruud system. Customer reported HVAC system stopped working due to clogged filter, which was cleared prior to arrival, but unit failed to restore operation after power cycling at switch and breaker. Upon arrival, performed diagnostic evaluation of outdoor condenser unit and thermostat communication. Identified underlying electrical or control board issue preventing system restart following filter blockage event. Completed troubleshooting procedures using testing equipment to isolate fault in system controls. Restored system operation and verified proper cooling function at thermostat and condenser unit.

Completed annual cooling maintenance on EnergiAir system. Verified and updated customer contact information in service records. Inspected condensate pump assembly, noting normal dust accumulation on housing and confirmed proper drainage line connections with PVC components functioning as designed. All system components operating within manufacturer specifications.

Completed annual cooling system maintenance and inspection. Performed standard tune-up procedures including filter check, electrical connections inspection, and system operational testing. Documented equipment condition with photos showing condensate drain pan with operational indicator lights functioning properly. System operating within normal parameters with no immediate service needs identified.

Repaired dripping single-handle Delta shower valve by replacing worn internal cartridge and seals. Tested operation to confirm proper function and verified no leaks present upon completion.

Completed full HVAC system replacement including outdoor condensing unit and indoor air handler. Installed new refrigerant lines with proper brazing and insulation, verified factory refrigerant charge of 65 ounces total, and performed leak test on all connections. Connected new equipment to existing ductwork in basement, ensured proper electrical connections, and commissioned system with startup procedures. Verified proper airflow, temperature differential, and system operation before completion.