Top-Rated HVAC & Plumbing Services in Spring Lake, MI

Responded to plumbing leak occurring during shower use. Diagnosed issue as improper pipe connection in wall cavity behind shower fixture. Installed new PVC drainage piping with proper slope and sealed penetrations through subfloor using rubber boot flashing. Verified all joints were secure and tested system to confirm leak was eliminated.

Completed annual heating maintenance on furnace system. Performed comprehensive tune-up including inspection of all mechanical components, burner assembly, heat exchanger, blower motor, and safety controls. Documentation photos captured showing existing equipment condition with visible age-related corrosion on mounting hardware and metal components, though system operational. No humidifier present on system. Unit tested and confirmed proper operation upon completion.

Conducted on-site evaluation for standby generator installation. Assessed existing electrical panel location and capacity, documented current service entrance configuration, and evaluated gas meter placement and condition for generator fuel supply connection. Photographed electrical infrastructure and gas utility equipment to support equipment sizing and installation planning.

Technician responded to a miscellaneous plumbing repair request and assessed the installation site. Upon inspection, identified the necessary components and connections in the utility area, including copper piping, PVC lines, and an outlet box with brass fittings and valve assembly. Documented the existing conditions with photographs for reference. Work is currently on hold pending parts procurement, with technician scheduled to return to complete the installation once the required component arrives.

# Tankless Water Heater Tune-Up Service Completed comprehensive tune-up service on a 4-year-old Rinnai tankless water heater unit. Performed standard maintenance protocol including descaling flush of the heat exchanger, inspection of all inlet/outlet connections and isolation valves, and verification of proper venting system integrity. Tested unit operation through full heating cycle, confirmed appropriate temperature output and flow rates, and verified all safety controls functioning within manufacturer specifications.

Completed installation of new Emergi furnace with PVC venting system in utility area. Installation included proper connection of all electrical components, ductwork, and adjacent air quality system. All components were securely mounted, connections properly sealed, and system was tested for proper operation before completion.

Completed 4 hours of kitchen rough-in plumbing work, installing PVC drainage system with multiple joints and connections. Installed copper supply lines between floor joists and verified proper P-trap configuration for kitchen fixtures. Will return to complete remaining kitchen plumbing installation.

Performed annual furnace tune-up on 9-year-old Amana system. Inspected burner assembly which showed normal wear but proper operation. Noted condensate pump with visible dirt accumulation and standing water in the collection tray; cleaned components and verified proper drainage function to ensure optimal system performance.

Successfully shut off and capped gas line in basement area as requested. Noted presence of moisture damage and rust on adjacent pipes, with visible mold growth on wooden ceiling joists that may require future attention.

Responded to follow-up service call for previously reported running toilet issue. Upon inspection, adjusted flapper and fill valve assembly to resolve continuous running. Verified proper flush operation and water shut-off before completing service.

Responded to sump pump failure issue; found significant corrosion and wear on existing pump components. Installed new vertical PVC discharge pipe system with rubber couplings and metal hose clamps, ensuring proper connection to drainage system. Completed installation and verified proper pump operation before leaving premises.

Successfully installed expansion tank on hot water system. Mounted new blue expansion tank vertically with proper copper pipe connections to existing water heater. Verified system operation and checked for leaks after installation.

Successfully completed installation of a CAPFA2422B3 air conditioner system, replacing the previous unit as requested. The new system was properly connected to the existing furnace and ductwork in the basement utility area, with all appropriate electrical connections secured and system tested for proper operation.

Completed replacement of severely corroded cast iron cleanout in basement with new PVC components. Work involved removing the deteriorated section, installing compatible fittings, and ensuring proper connections to existing plumbing system. Final inspection confirmed no leaks and restored full functionality to the waste line cleanout access.

Diagnosed and repaired malfunctioning toilet system by replacing the damaged flush valve assembly. Discovered significant mineral buildup on the old valve which was preventing proper water flow and seal formation. After installation of new components, tested system functionality and confirmed complete resolution of the issue.

Replaced damaged dishwasher supply line with new braided stainless steel line and installed brass valve regulator to ensure proper water flow. Verified all connections were secure with no leaks before restoring water service to the appliance.

Inspected customer's recently purchased washer that was leaking into floor drain during operation. Examined and repaired upstairs sink drain that was not sealing properly and unable to hold water. Documented corrosion and deterioration of yellow-painted pipes in the utility area, noting significant rust development and degradation of pipe coating that requires future attention.

Returned to complete quoted toilet repair service. Inspected toilet mounting system and connection to floor. Verified proper installation of plumbing supply lines (PVC, red and blue pipes) secured with appropriate brackets against OSB wall structure.

Installed new kitchen faucet in a 50-year-old home, replacing an existing unit that had been problematic for approximately one month. Successfully completed installation of the modern pull-down stainless steel faucet with single lever handle, ensuring proper functionality and no leaks.

Completed Sterling shower installation with client valve assembly and CWOW. Successfully installed shower valve/mixing valve within wall cavity after accessing plumbing through opened wall with exposed studs. Project involved working around existing insulation and preparing the area for subsequent drywall finishing.