Top-Rated HVAC & Plumbing Services in Spring Lake, MI

Performed annual heating tune-up on 17-year-old Amana furnace, including inspection of the burner assembly and heat exchanger sections and verification of electrical operation with a multimeter. Identified rust and corrosion on the burner/heat exchanger components, indicating heat exposure and wear, and documented findings with photos for the customer's records.

Performed a Super Tune-up on an 11-year-old gas furnace and humidifier, including inspection of the burner assembly, gas valve, inducer motor, pressure switch, vent coupling, and wiring connections. Noted shredded fiberglass insulation and debris scattered throughout the burner compartment and on the gas valve and vent coupling, consistent with rodent nesting, along with light rust staining near the wiring; recommend further evaluation to confirm the source and prevent recurrence. Customer was enrolled in the maintenance club during the visit.

Responded to a complaint of loud, vibration-type noise from a 9-year-old furnace that remained operational. Inspected the unit and associated condensate drainage components, including the condensate pump, flexible drain hose, and PVC drain piping, and evaluated them as potential sources of vibration and noise during operation.

Performed an on-site plumbing estimate for relocating the washer, dryer, and laundry sink to a different area of the laundry room. Inspected the existing water supply piping and shutoff valve, noting oxidation and tarnish at the joints, along with the sink drain assembly, P-trap, and horizontal drain line under the laundry sink, which showed no visible leaks or corrosion. Documented existing conditions with photos to scope the water line, drain, and any gas line relocation required for the new layout.

Performed annual furnace tune-up and inspection, including evaluation of the gas control valve assembly, wiring, and pressure switch components, with the gas valve adjustment cap confirmed factory-sealed with "DO NOT ADJUST" labeling. Inspected the return air filter and found heavy lint and debris loading across the pleated media, indicating the filter requires replacement to maintain proper airflow and heating efficiency.

Inspected the furnace for the reported water leak and traced it to the condensate drain system, where the rubber drain hose connection at the collection reservoir was seeping due to a corroded, deteriorated spring clamp and mineral buildup around the fitting. Cleared the debris and scale from the affected area and restored a secure, watertight hose connection, confirming the leak was resolved and condensate drains properly.

Responded to a no-heat call on a Bryant gas furnace (approx. 10 years old) and inspected the unit's internal wiring harness and gas valve assembly. Found loosely routed, cluttered low-voltage wiring in the control compartment; bundled and secured the wires with zip ties to restore proper routing and prevent interference with the gas valve and surrounding components. Verified no visible rust, frost, or physical damage to the cabinet interior.

Performed annual heating tune-up on the furnace and humidifier. Inspected the burner assembly and found heavy rust and corrosion on the burner component, indicating deterioration that should be addressed to maintain safe, efficient operation. Serviced the humidifier and replaced the water panel/pad, with the drain pan showing buildup and residue consistent with mineral deposits.

Performed annual heating tune-up on Goodman furnace and humidifier, including inspection of components, cleaning, and verification of proper operation. Inspected condensate and PVC drain piping at the unit; noted dampness and staining on the concrete floor near the pipe base, which should be monitored for leaks or drainage issues.

Installed a new 50-gallon LP power vent water heater, completing the water, gas, and venting connections and placing the unit in a drain pan with a leak sensor. Routed and secured the PVC vent/intake piping and condensate drain to the exterior, then verified proper operation and leak-free connections.

Performed annual heating tune-up on 22-year-old Bryant furnace and inspected the galvanized flue vent pipe for the surface crack reported by the gas company. Observed scattered surface corrosion and oxidation along the vent pipe sections, particularly near the band joints and seams, with no obvious separation or major damage visible; connections remain secured with metal bands and fasteners. Recommend continued monitoring of the vent pipe condition and consideration of vent replacement as the corrosion progresses.

Installed a 20kW Kohler standby generator with a 200A service upgrade, coordinating a utility disconnect/reconnect and completing all electrical work under the required electrical and mechanical permits. Connected the natural gas supply and performed a gas line pressure test, holding approximately 15–17 PSI with no leaks, which was verified and approved by the inspector.

Responded to a reported tank leak on a 14-year-old Bradford White power-vent water heater and inspected the unit, including the blower and vent assembly, PVC exhaust piping, copper supply lines, shutoff valves, and drain piping. The tank and connections showed no visible rust, frost, or active leaking at the time of inspection, and all fittings appeared intact. Same-day emergency service was unavailable, so the customer was placed on the priority schedule for expedited follow-up.

Completed PSI-Sink installation for double-basin stainless steel sink with chrome faucet, connecting all plumbing components including garbage disposal unit, supply lines, and drain assemblies under newly installed countertops. All connections tested and verified operational with no leaks detected.

Completed annual heating maintenance on 2013 EcoAir furnace system. Performed comprehensive tune-up including inspection of all major components, burner assembly cleaning, heat exchanger examination, blower motor service, and filter replacement. Verified system operation, confirmed proper ignition sequence, and tested safety controls. Customer confirmed best contact number and indicated no humidifier present on system. Unit operating efficiently with no issues found.

Completed annual heating maintenance on Bryant furnace and humidifier system. During inspection, discovered severely corroded humidifier solenoid valve assembly with significant calcium and mineral buildup affecting operation. Documented corroded components with photos and inspected water supply valve feeding humidifier, which showed normal wear but remained functional. Performed standard tune-up procedures on heating system and assessed humidifier condition for future service recommendations.

Completed full HVAC system replacement including installation of new furnace, air conditioning unit, and water heater. Interior furnace and water heater installed in basement utility area on protective mat with proper PVC venting, condensate drainage, and gas line connections. Exterior AC unit positioned on ground-level pad with refrigerant lines run through metal conduit along foundation wall, electrical disconnect boxes mounted, and all connections properly secured and tested for operation.

Completed full water heater installation in basement utility area. Removed existing unit and installed new residential cylindrical water heater on concrete floor against cinder block foundation wall. Connected copper supply and discharge lines to top of unit with proper fittings and soldered joints. Installed pressure relief valve with discharge piping per code requirements. Routed all plumbing connections through exposed floor joists above, securing lines with appropriate strapping and brackets. Verified all connections for proper operation and tested unit for leaks.

Provided estimate for replacement of existing Bradford White water heater in residential basement mechanical room. Assessed current installation including copper supply lines, galvanized ductwork connections, expansion tank with blue flexible connector, and associated plumbing components with brass fittings and shutoff valves. Documented existing configuration and presented replacement options to customer.

Completed annual heating maintenance on 20-year-old AirEase furnace system. Performed comprehensive tune-up including inspection of all major components, burner assembly cleaning, ignition system testing, and safety control verification. Confirmed humidifier is not active per customer's club service agreement. All systems operating within normal parameters at time of service completion.