Top-Rated HVAC & Plumbing Services in Spring Lake, MI

Completed annual heating maintenance on two furnace systems: a 16-year-old Energi unit and an 18-year-old Amana unit, including humidifier tune-up services. Performed comprehensive inspection of both systems, checking flame sensor operation and cleaning components as needed. Tested all safety controls, verified proper ignition sequence, and confirmed adequate airflow through ductwork. Both furnaces operating efficiently with all systems functioning within normal parameters.

Conducted comprehensive site assessment for exterior spigot installation. Evaluated existing plumbing infrastructure including interior copper supply lines with shutoff valve access through ceiling cavity and exterior drainage system along foundation. Documented current pipe routing, identified optimal connection points for new hose bib installation, and assessed structural considerations for wall penetration through concrete block exterior. Photographed interior water supply configuration and exterior mounting location near landscaped drainage area to develop accurate material list and installation plan for customer approval.

Completed annual heating maintenance and furnace tune-up on approximately 2-year-old system. Unit exhibited significant age-related wear with dust accumulation, interior discoloration, and oxidation on metal components. HydroJet water system showed extensive deterioration with peeling exterior coating and rust damage on top surface, along with visible moisture staining on surrounding floor area.

Completed on-site evaluation for tankless water heater replacement estimate at single-family residence. Assessed existing water heater installation in basement, documented current gas meter configuration showing significant corrosion on inlet/outlet connections and upper piping, and evaluated utility infrastructure including pressure regulator and gas supply lines. Photographed basement plumbing configuration with exposed framing, existing water supply pipes, and shut-off valves to determine feasibility and requirements for tankless conversion installation.

Responded to water leak concern related to furnace condensation on floor. Upon inspection, identified PVC condensate drain piping in basement showing water staining and mineral deposits on exterior surfaces. Verified drainage system components including vertical waste pipes and elbow fittings for proper operation. Documented conditions with photographs showing discoloration on PVC piping and surrounding basement infrastructure. System evaluated to ensure condensate drainage functioning as designed with no immediate concerns requiring repair.

Completed annual heating maintenance on an 11-year-old EnergiAir furnace system. Performed comprehensive tune-up including inspection of heat exchanger, burner assembly, ignition system, and venting components. Verified proper operation of all safety controls, checked gas pressure and combustion efficiency, cleaned blower assembly, replaced air filter, and documented system specifications. All components found operating within manufacturer specifications with no immediate concerns noted.

Removed and reset toilet in residential bathroom to address underlying issue. Pulled toilet from flange, inspected wax ring and floor mounting, then reinstalled with proper seal and secure mounting to restore full functionality.

Responded to service call for loose toilet in master bathroom and pedestal sink replacement consultation. Secured toilet to floor by tightening closet bolts and checking wax ring seal for proper installation. Verified toilet stability and tested for any rocking or movement. Assessed existing pedestal sink for replacement, taking measurements of current installation height and discussing fixture options with customer. Documented sink dimensions and plumbing configuration with photographs for future replacement planning. All plumbing connections inspected and found to be functioning properly with no leaks detected.

Completed comprehensive tankless water heater tune-up service including system inspection, flushing, and performance verification. Unit operational and functioning within manufacturer specifications upon completion.

Completed comprehensive furnace tune-up on 1-year-old Carrier unit, model WT 11-2034. Verified best contact number with customer, performed standard maintenance procedures including inspection of all system components, condensate pump operation, drainage lines, and ductwork connections. System operating within normal parameters with all safety checks confirmed and photographic documentation captured for service records.

Completed annual heating maintenance on 23-year-old Bryant furnace and humidifier system. Performed comprehensive tune-up including inspection of all major components, verified proper operation of condensate pump with drainage system, confirmed air filter condition and airflow, tested safety controls and electrical connections, and documented equipment condition through photographic records. System operating within normal parameters upon completion.

Responded to no hot water complaint on tank-style water heater. Upon arrival, accessed unit through rear entrance as requested. Inspected water heater installation in utility space, noting aged plumbing components with visible corrosion and patina on brass valve assembly and copper piping connections. Documented existing conditions including tarnished brass fittings, soldered copper joints, and overall system age indicators. Assessed valve operation, supply connections, and distribution piping in confined mechanical space. Customer is active plan member and was prioritized for service response.

Completed comprehensive furnace super tune-up on a Heil unit over 10 years old. Performed full system inspection, cleaned and tested all components, verified proper operation of safety controls, and confirmed efficient heating performance with no issues found.

Completed estimate for air conditioning system in residential property. Documented existing HVAC equipment in basement utility room, including furnace unit, air handler, associated ductwork, and plumbing connections. Photographed current system configuration and mechanical room conditions to prepare comprehensive cooling system replacement proposal for tenant-occupied property.

Conducted comprehensive assessment of existing HVAC system for furnace and air conditioning replacement estimate. Air conditioning unit has been non-operational for approximately two years. Evaluated current air handler installation in mechanical closet, noting equipment configuration with water heater in shared utility space. Documented existing ductwork connections, airflow pathways, and spatial constraints for equipment replacement planning. Assessed plumbing infrastructure including water shut-off valve assembly and piping configuration to determine compatibility requirements for new system installation. Photographed equipment layout, clearances, and utility connections to provide accurate replacement specifications and installation planning.

Installed back plate for digital thermostat on interior wall. Thermostat mounted securely and displaying proper temperature readings with all control functions operational.

Completed annual heating maintenance on furnace system, treating as initial service visit per customer request. Performed comprehensive tune-up including inspection of all system components, burner assembly, heat exchanger, blower motor, and electrical connections. Discovered corroded flame sensor requiring replacement; removed old sensor showing significant buildup and oxidation, installed new sensor to ensure proper flame detection and system safety. Inspected control board wiring and connections, verified all wire terminations secure at terminal blocks. Documented system condition with photos of replaced component and control panel wiring configuration for service records.

Completed comprehensive furnace super tune-up on 11-year-old Bryant unit located in utility closet area. Performed full system inspection, cleaned and tested all components, verified proper operation of condensate pump and drainage system, and confirmed unit is functioning within manufacturer specifications.

Returned to property to complete previously quoted garbage disposal replacement. Removed existing disposal unit and installed new unit beneath kitchen sink, connecting to existing drain assembly and plumbing infrastructure. Verified proper operation of new disposal, tested for leaks at all connection points, and confirmed secure mounting to sink flange. Work completed within estimated 2-hour timeframe with customer present on-site.

Completed installation of new water softener system in utility room basement area. System consists of dual-tank configuration with digital control head mounted on upper resin tank and lower brine tank for regeneration cycle. Connected unit to existing plumbing infrastructure, integrated with blue supply piping visible on tiled wall, and programmed digital controller for optimal water treatment performance.