Top-Rated HVAC & Plumbing Services in Spring Lake, MI

Responded to service call for leaking outdoor hose bib. Upon inspection, found standard brass spigot with wheel-style handle valve mounted on exterior wall above foundation level showing signs of weathering, corrosion, and mineral deposits. Diagnosed leak source, performed necessary repairs to stop water discharge, and tested fixture to confirm proper operation. Documented completed work with photographs showing spigot assembly, wall mounting, and surrounding installation area.

Responded to no heat call where customer reported outdoor AC fan activating when calling for heat and uncertainty about pilot light status. Upon inspection, verified thermostat operation and system response, confirmed proper thermostat settings at 69 degrees. Diagnosed heating system issue, restored proper furnace operation, and verified heating cycle engaged correctly without outdoor unit interference.

# Furnace Ignition Failure - Pressure Switch Replaced Responded to no-heat call on 6-year-old Bryant furnace. Upon arrival, confirmed unit was not firing. Draft inducer motor would run for approximately 2-3 minutes then shut down without pilot ignition occurring. Performed diagnostic testing and determined pressure switch was faulty and not closing circuit to allow ignition sequence to continue. Removed defective pressure switch assembly and installed new replacement unit. Verified proper draft inducer operation, confirmed pressure switch closure, and tested complete ignition cycle. Furnace now operating normally with proper heating output.

Completed complimentary annual cooling system tune-up on 6-year-old Comfort Maker/ICP unit. Performed comprehensive preventive maintenance inspection, verified thermostat operation showing 66°F ambient temperature with 70°F setpoint and 63% humidity level, confirmed cooling mode and auto fan settings functioning properly, and documented system condition with photographs.

Completed annual heating maintenance inspection on 15-year-old furnace and hydronic heating system. Inspected circulator pump, copper piping network, manifold distribution system with multiple zone valves, expansion tank, and water heater connections. All components photographed and found operating within normal parameters; system ready for heating season.

Responded to a water leak emergency in the mechanical room affecting the furnace. Identified and repaired a leaking elbow fitting on the recirculating line between the water heater and furnace that was actively spraying water onto the furnace equipment. Additionally, replaced a faulty shut-off valve on the humidifier water feed line that was also leaking. Both repairs completed to restore proper operation and prevent water damage to HVAC equipment.

Completed annual heating maintenance on Carrier furnace model WT 06-2036. Performed comprehensive system diagnostics using calibrated testing equipment, inspected all major components, and verified proper operation of heating system for seasonal readiness.

Completed annual cooling system tune-up and preventative maintenance on residential HVAC unit. Inspected electrical components including Power Guard surge protection device and associated wiring connections. Removed and cleaned blower assembly which showed significant accumulation of dust and debris throughout interior compartment. Verified proper operation of all system components and restored unit to optimal working condition.

Responded to water leak call for Goodman furnace system. Upon inspection, identified leak source originating from condensate drainage system. Collected water in basin to prevent further damage to surrounding area. Evaluated water heater and associated plumbing connections in utility space, noting copper piping configuration and gas valve positioning. Documented existing conditions of Bradford White water heater installation and connected plumbing infrastructure for reference. Provided membership renewal information as requested.

Inspected two outdoor faucets showing active leaks and provided repair/replacement quote as requested. The first faucet, a chrome cross-handle spigot mounted on brick exterior, exhibited leakage evidenced by white mineral deposits and water staining on concrete below. The second location featured a backflow prevention assembly with multiple valves on gray siding, also connected to garden hose with visible moisture concerns on surrounding pavers.

Responded to no hot water complaint on Rheem water heater less than 10 years old. Upon arrival, inspected unit and documented installation with photos showing water heater and adjacent Goodman HVAC system in basement utility area. Diagnosed issue and restored hot water functionality to residence.

Responded to service call for garbage disposal installation. Upon arrival, found existing kitchen sink with standard drain assembly in place. Removed old drain components and prepared sink opening for new disposal unit. Installed new garbage disposal unit under stainless steel sink basin, ensuring proper mounting bracket alignment and secure attachment to sink flange. Connected discharge plumbing and verified all electrical connections per manufacturer specifications. Tested unit operation and checked for leaks. Disposal functioning properly with no drainage issues detected upon completion.

Completed annual cooling maintenance on 9-year-old Goodman system with 2017 condenser model. Performed comprehensive tune-up including filter inspection, refrigerant level check, electrical connection testing, condensate drain verification, and overall system performance evaluation. Unit operating within normal parameters with no deficiencies noted at time of service.

Responded to customer concern regarding increased energy consumption following thermostat replacement. Inspected White-Rodgers digital thermostat installation and verified proper mounting and functionality with display reading 74°F. Examined HVAC system air filter and found heavily soiled pleated media requiring replacement, which can significantly impact system efficiency and runtime. Recommended immediate filter replacement to restore proper airflow and reduce excessive system cycling that contributes to elevated energy usage.

Completed installation of residential water softening system in basement utility area, including mounting and connecting cylindrical treatment tank with control valve assembly and accompanying brine tank. All plumbing connections were made using copper piping integrated with existing water supply lines, system was tested and confirmed operational.

# AC Annual Cooling Maintenance - 26-Year-Old Heil System Completed annual cooling maintenance on a 26-year-old Heil air conditioning system. Upon inspection, discovered severe corrosion and rust throughout the electrical housing and contactor assembly, indicating long-term moisture exposure and environmental deterioration. The metal casing showed extensive pitting and orange-brown discoloration with significant rust accumulation around wire connection points. Electrical components including the contactor displayed worn wire insulation on red, yellow, black, and green conductors. Debris and organic material had accumulated around electrical connections within the corroded housing. Documented the advanced deterioration of the compressor unit and electrical components through photographs. The system's age and extensive corrosion present significant reliability and safety concerns. Strongly recommend replacement of the outdoor unit due to the compromised structural integrity of the elec

Responded to cooling issue on recently installed HVAC system experiencing excessive condensation on supply vents and cold air leaking from four duct seams. Inspected air handler and ductwork in mechanical room, identifying inadequate sealing at duct connections allowing conditioned air to escape and causing moisture accumulation on registers. Documented equipment installation including air handler unit, water heater, and associated piping systems through photographic evidence showing equipment labels, leak detection system components, and overall mechanical room layout for warranty documentation purposes.

Performed on-site evaluation for water softener replacement estimate at residential property. Inspected existing Culligan water conditioning system currently installed in utility closet with adequate plumbing infrastructure including copper supply lines, brass fittings, and PVC drain configuration. System operational with digital control panel functioning properly and salt supply present. Assessed installation location featuring white tile walls, concrete flooring, and sufficient clearance for equipment access and maintenance. Documented existing plumbing layout including vertical and horizontal blue PVC piping network, connection points on concrete block wall, and proximity to water heater. Photographed current system configuration, utility room conditions, and available workspace for potential replacement installation. Reviewed customer interest in alternative water conditioning solutions and service options compared to current provider.

Conducted comprehensive assessment of existing boiler heating system and evaluated property for potential mini-split installation to provide modernized HVAC solution. Inspected current boiler unit with associated PVC venting, copper piping, expansion tank, and distribution lines to determine replacement specifications and compatibility with existing infrastructure. Documented equipment conditions, measured available space for new installations, and assessed electrical and structural requirements for ductless mini-split system integration while coordinating with plumbing contractor addressing concurrent household needs.

Conducted on-site assessment of existing galvanized plumbing system in older residential property to provide estimate for complete PEX repiping conversion. Inspected basement and crawlspace areas, documenting current plumbing infrastructure including existing PEX hot and cold water supply lines, copper piping with insulation, and PVC drainage components. Photographed pipe routing, joist configurations, and connection points to determine scope of work for replacing remaining galvanized pipes with PEX supply lines throughout the home.