Top-Notch HVAC, Plumbing & Generator Services in Battle Creek, MI

Completed annual cooling maintenance on 3-year-old Carrier unit under warranty through September 2027. Inspected system components, verified proper operation, and documented existing vintage thermostat and electric baseboard heating system with photos for service records.

# CP-Cooling Problem Resolution Responded to no airflow complaint with unit frozen over. Upon arrival, found evaporator coil completely iced, restricting all airflow to living space. Verified blower motor operation and measured amp draw at 0.67A and 0.10A under different conditions using digital meter, confirming motor functionality within acceptable range. Identified frozen coil as primary issue preventing air circulation. Shut down system to allow complete defrost of evaporator coil. Inspected air filter, ductwork accessibility, and blower compartment for restrictions or maintenance concerns. Monitored system components during diagnostic process to determine root cause of freeze condition. Documented equipment readings and conditions with photos for service records. Unit is 0 years old Carrier model with warranty expiration July 2027. Advised on proper system operation and maintenance to prevent future freeze-ups.

Completed annual cooling maintenance and tune-up on EnergiAir system per manufacturer specifications. Inspected condensate pump assembly, verified proper drainage operation, and documented mechanical equipment condition with photographs. All components tested and operating within normal parameters.

Completed annual cooling maintenance on 9-year-old Trane system. Performed standard inspection of unit components, verified system operation, and documented equipment condition with photos. System operating within normal parameters with contract maintenance due in 2026.

# No Cool Service Call Responded to service call for air conditioning unit not turning on. Upon arrival, inspected 9-year-old system and associated components. Evaluated condensate pump assembly located in basement utility area, which showed signs of operational issues. Pump unit was positioned on collection reservoir with discharge piping and electrical connections visible. Assessed power supply, pump functionality, and drainage system to determine cause of AC system failure. Documented equipment condition and installation setup with photographs for service records. Condensate pump malfunction was identified as primary factor preventing air conditioning operation, as safety switch likely triggered shutdown to prevent water damage from backup.

Relocated and installed shower valve assembly in bathroom with decorative tile work. Accessed plumbing through wall cavity, repositioned PEX supply lines and valve body, then mounted chrome shower valve with escutcheon plate on white subway tile section below mosaic glass tile accent band. Secured all connections and restored wall access point.

Responded to no-heat complaint on 15-year-old AO Smith water heater. Upon inspection, documented existing installation including copper supply lines, proper venting through exterior wall, and drain pan placement. Unit showed signs of age-related wear consistent with end of typical service life for residential water heaters.

# CP-Cooling Problem Resolution Responded to service call for air conditioning unit experiencing intermittent operation - system would run and produce cold air before shutting down unexpectedly. Upon arrival, performed comprehensive electrical diagnostics using digital multimeter to identify the root cause of the premature shutdown. Conducted amperage measurements on the compressor circuit, which revealed a reading of 22.2 amps during operation. Further electrical testing indicated abnormal readings displayed as "E.E.E" on the meter, suggesting an electrical fault condition within the system. Inspected all wire connections, including multi-phase power wiring (green, red, blue, and black conductors) connected to the compressor motor assembly. Verified integrity of capacitor and associated electrical components within the control circuit. Diagnosed issue as electrical fault causing safety shutdown of the system. Addressed the problem by correcting the electrical anomaly, ensuring all

Returned to property to retrieve water testing kit as requested. Kit was successfully picked up and documented with photos for service records.

Successfully removed the existing kitchen faucet and installed a customer-supplied touchless faucet unit in the kitchen sink area. Disconnected water supply lines, removed old mounting hardware, and prepared the mounting surface on the butcher block countertop. Installed the new touchless faucet with chrome finish and pull-down spray head, ensuring proper alignment and secure mounting through the existing sink deck holes. Connected hot and cold water supply lines, installed the electronic sensor components and battery pack per manufacturer specifications, and tested all functions including touchless activation, manual lever operation, and spray modes. Verified no leaks at connections, confirmed proper water flow and temperature control, and ensured the touchless sensor responded correctly to hand proximity. System is fully operational with no issues noted.

Completed annual cooling maintenance on residential HVAC system. Performed comprehensive tune-up inspection of air conditioning equipment, including examination of refrigerant lines, condensate drain trap assembly, and evaporator coil. Inspected copper refrigerant lines, electrical connections, and white PVC condensate drainage system for proper operation. Examined evaporator coil fins and noted minor dust accumulation between fin surfaces. Verified proper condensate trap installation and drainage function. Documented equipment condition with photographs showing furnace/air handler unit, refrigerant piping, and coil condition. System operational and ready for cooling season. Enrolled customer in club membership program covering furnace, air conditioning, and humidifier equipment for ongoing maintenance coverage.

Completed whole home water repipe installation over two-day period, replacing existing plumbing supply lines throughout the residence. Installed new PVC supply piping in attic space, properly secured to structural framing with mounting clips, and upgraded mechanical room plumbing infrastructure including connections to water heater and pressure tank systems. All new piping was professionally routed, secured to code specifications, and tested for proper operation upon completion.

Completed annual cooling system tune-up and inspection on aging HVAC unit over 10 years old. Inspected condensate pump operation and drainage system, verified proper function with both discharge lines connected and green indicator light operational. Observed active condensation removal from evaporator coil with moisture present on collection cylinder, confirming system is cooling effectively and condensate management equipment is working as designed.

Responded to service call for salt mistakenly added to water heater instead of water softener unit. Salt failed to dissolve, resulting in water discoloration and odor issues. Assessed system contamination, documented conditions with photos, and provided customer education on proper water softener maintenance and distinction between water heater and water softener systems to prevent future occurrences.

Completed comprehensive plumbing system repair on water heater installation with focus on pressure regulation and valve assembly replacement. Addressed deteriorated flexible connector hoses and corroded copper piping connections, installed new brass ball valves and pressure gauge assembly to restore proper system monitoring and flow control. Remediated moisture damage area and ensured all connections were properly sealed to prevent future water intrusion and corrosion issues.

Completed annual cooling system tune-up on 20-year-old Haier unit with condenser model year 2022. Performed standard maintenance inspection, documented equipment installation and electrical connections including grounding wires and power supply components in basement utility area. All systems operating within normal parameters upon completion.

Completed kitchen faucet installation, replacing the existing fixture with a new chrome single-handle model with pull-out spray attachment. Addressed gas line concern by removing saddle clamp from 3-foot section of gas piping in the ceiling cavity, ensuring proper gas line integrity and code compliance. Verified all plumbing connections for leaks, tested faucet operation and water flow in both basins, and confirmed proper drainage function.

Responded to complaint of gurgling tub drain when toilet flushed and strong acidic odor in 60-year-old home with septic system. Accessed plumbing system through basement/crawlspace to inspect drain and vent piping. Upon investigation, identified venting issue in drain-waste-vent system causing negative pressure when toilet discharged, resulting in gurgling at tub drain and allowing sewer gases to escape into living space. Documented existing plumbing configuration with photos showing copper drain lines, vent pipes, and connection points between fixtures to assess proper venting and drainage flow for this single-bathroom home on septic system.

Completed installation of a 40-gallon Bradford White natural gas atmospheric vent water heater in basement location. Unit was properly positioned on metallic base plate, with all copper supply and discharge piping connected per manufacturer specifications and local code requirements. Gas line connection, temperature and pressure relief valve, and venting system were installed and tested for proper operation and safety compliance.

Removed existing gas line and successfully rerouted new gas line for outdoor grill installation. Work was performed in basement/crawl space area, routing new copper gas line along ceiling joists to exterior location. Installation included proper mounting hardware, shutoff valve, and compliance with gas line code requirements for outdoor appliance connection.