Top-Rated HVAC & Plumbing Services in Grand Haven, MI

Completed annual heating maintenance on 11-year-old furnace and humidifier system. Performed comprehensive tune-up including inspection of all mechanical components, burner assembly, heat exchanger, blower motor, and electrical connections. Verified proper operation of humidifier, checked drainage system, and tested all safety controls for optimal winter performance.

Completed same-day installation of new tankless water heater system in residential utility closet. Removed existing water heating equipment and installed wall-mounted tankless unit with proper venting using white PVC piping, integrated copper and PVC supply lines with brass fittings and shutoff valves, and installed pressure regulation and filtration components. All plumbing connections tested and verified for proper operation, unit programmed and commissioned per manufacturer specifications.

Performed water testing on plumbing system and identified active leak at test valve assembly near water heater. Documented existing corrosion and rust on pipe sections, along with floor staining indicating previous water intrusion. Photographed safety tag on vertical pipe assembly and overall condition of affected components for follow-up repair recommendations.

Responded to no-start air conditioning complaint where outdoor condenser unit was buzzing but compressor not running. Upon inspection, identified 20+ year old system with failed compressor and associated electrical components. Documented existing basement HVAC installation including furnace, ductwork, and mechanical room configuration, as well as outdoor condenser unit location and condition. Provided estimate for compressor replacement or full system replacement options given age of equipment.

Responded to service call for 8-year-old Richmond tankless water heater with no hot water production. Upon arrival, accessed unit's internal components by removing front panel to diagnose heating failure. Inspected heat exchanger assembly, control board, electrical connections, and wiring harness for potential faults. Examined venting system including intake and exhaust PVC piping for proper configuration and blockages. Documented internal component condition including circuit board, wire connections, and heat exchanger coils through photographic evidence. Completed diagnostic assessment of non-operational tankless water heating system.

Responded to water leak caused by broken condensate drain pipe on 14-year-old Rheem HVAC unit. Upon arrival, found the white PVC condensate pipe elbow fitting had separated from the system, resulting in active water discharge onto the equipment and surrounding area. Repaired the damaged condensate drain connection, restored proper drainage function, and verified system operation. Documented existing moisture on metal panels and components due to the leak prior to repair.

Completed estimate for replacement of 28-year-old non-functional air conditioning system and operational furnace in basement mechanical room. Customer requested both units be replaced simultaneously for system compatibility and efficiency. Documented existing equipment conditions including aged furnace with active combustion chamber, deteriorated ductwork, and associated HVAC components through photographic assessment for replacement proposal.

Responded to failed inspection for IRC G2420.5 code violation regarding appliance gas shut-off valve location. Installed compliant gas shut-off valve within 6 feet of appliance to meet G2420.5.1 requirements, as existing valve at meter was located over 40 feet away and did not satisfy code. Work completed and ready for re-inspection.

Completed annual cooling maintenance on 12-year-old Ruud air conditioning system. Performed comprehensive tune-up inspection, checked refrigerant levels, cleaned condenser coils, tested electrical connections, and verified proper system operation. Documented equipment condition with photos showing filter inspection.

Responded to report of furnace leaking on a two-year-old EnergiAir unit. Upon inspection, identified water accumulation in the condensate drain system. Examined internal components including the drain pan, PVC condensate line connections, and associated plumbing. Verified gas valve assembly and electrical connections were functioning properly and not contributing to moisture issues. Documented equipment condition with photos showing drain pan area, copper refrigerant lines, and condensate removal system components for warranty reference.

Performed comprehensive assessment of existing residential air conditioning system including outdoor condenser unit and indoor air handler. System currently operational but showing signs of age and wear with potential reliability concerns. Evaluated equipment condition, ductwork configuration, and installation setup to provide estimate for full system replacement and potential ductless mini-split installation as alternative or supplemental cooling solution.

Installed new gas line for dryer from basement to laundry area on main floor. Gas valve with red shutoff handle mounted at floor level with black mounting plate, copper supply line run through ceiling joists and connected to existing gas distribution system in basement.

Responded to service call for 40-year-old boiler system in single family residence requiring second opinion evaluation after previous replacement quote. Performed comprehensive inspection of aged boiler unit and associated mechanical components, including assessment of copper piping showing significant corrosion and oxidation at fittings and connections. Documented equipment condition through photographic evidence of mechanical room infrastructure, noting visible deterioration of piping system and aging control components. Provided professional assessment and repair recommendations to customer as alternative to full system replacement.

Responded to a residential plumbing service call for clogged drains affecting two bathroom sinks that had been experiencing slow drainage for approximately 2-3 months. Upon arrival, assessed both bathroom sink drains and determined the clogs were isolated to the individual fixture drain lines rather than a main line obstruction. Successfully cleared both drain blockages using appropriate drain cleaning methods, restoring proper water flow and drainage function to both bathroom sinks. Additionally, installed two Moen Hydro Energetix handheld showerheads as requested. Completed installations included proper mounting of showerhead brackets, connection of flexible hoses, and verification of secure fittings with no leaks. Tested both newly installed showerheads for proper water pressure, spray pattern functionality, and confirmed all connections were watertight. All work performed in a 2019-constructed home with modern plumbing fixtures and granite countertops throughout the bathrooms.

Completed annual cooling maintenance on 2019 EcoAir system. Performed comprehensive tune-up including inspection of electrical components, capacitor testing, and contactor evaluation. Verified system operation and confirmed all components functioning within normal parameters. Updated contact information in service records and documented equipment condition with photos of electrical assembly showing TITAN PRO capacitor rated at 45+5 MFD and associated wiring connections.

Completed annual cooling maintenance on 21-year-old Goodman system. Performed comprehensive tune-up including inspection of condensate drain line and float mechanism, verified proper drainage operation, and confirmed all system components operating within manufacturer specifications. Updated customer contact information and documented equipment condition with photos.

Completed annual cooling maintenance on 18-year-old Amana system with coil manufactured in 2022. Performed standard tune-up procedures including inspection of condensate drain system and drain pan, verified proper drainage function, and documented equipment condition with photos. All components found operating within normal parameters.

Completed annual cooling maintenance on 20-year-old Payne air conditioning system and performed water heater tune-up. Inspected all components, verified refrigerant lines and PVC condensate drainage, checked system levels, and confirmed proper operation of both units. All equipment found in working order with no immediate concerns identified.

Successfully completed full furnace installation in residential mechanical room. Installed new gray metal furnace unit on protective base pad with proper positioning and mounting against wall. Connected white PVC ductwork with appropriate routing across ceiling area, including horizontal and vertical runs with proper angular transitions. Integrated air filtration system into duct configuration. Verified all mechanical connections, fittings, and safety compliance per manufacturer specifications. System tested and operational upon completion.

Conducted site assessment for installation of new exterior spigot in garage of single-family residence constructed in 2020. Evaluated existing plumbing infrastructure in unfinished basement, including water heater location, PVC supply lines, and copper piping routing through ceiling joists. Documented mechanical room layout and determined optimal connection point for new hose bib installation. Photographed current plumbing configuration to develop comprehensive project estimate for garage spigot addition.