Top-Rated HVAC & Plumbing Services in Grand Haven, MI

Completed annual cooling maintenance and tune-up on 4-year-old Goodman air conditioning system. Inspected all major components including evaporator coil, condensate drain system with PVC drain line, and interior base section with drain pan. All systems operating within normal parameters with no issues identified during inspection.

Successfully completed full air conditioning system replacement at residential property. Removed existing outdoor condensing unit and installed new Amana condenser on concrete pad adjacent to building exterior. Ran new refrigerant line set with proper insulation from outdoor unit to interior air handler, utilizing gray foam insulation on copper lines. Installed electrical disconnect box on exterior wall with appropriate conduit routing for power supply. Connected refrigerant lines with brass fittings and service valves, properly capped and secured all connections. Installed new PVC condensate drain line from unit through building siding. System was pressure tested, evacuated, and charged to manufacturer specifications. Verified all electrical connections, tested unit operation, and confirmed proper airflow through condenser fan assembly. Installation completed per manufacturer guidelines with all safety labels and warnings properly affixed to equipment.

Completed full furnace installation in basement utility area. Installed new beige furnace unit with proper ductwork connections, including horizontal supply plenum and vertical return air configuration. Connected all metal ductwork with appropriate elbow joints and secured all connections. Verified proper clearances from existing water heater and plumbing systems. Tested unit operation and airflow distribution to ensure optimal performance.

Responded to service call for reported thermostat issue with air conditioning system on 10-year-old Payne unit. Upon arrival, inspected Emerson digital thermostat mounted on exterior wall and examined zone control panel with damper and sensor connections. Verified thermostat display functionality, checked wiring connections at both thermostat and zone control terminal blocks, and confirmed proper voltage at R and C terminals. System demonstrated ability to cool as reported by customer. Photographed thermostat interface and zone control wiring configuration for documentation. All connections secure, no immediate faults identified during inspection.

Completed comprehensive AC Super Tune-up on 24-year-old Lennox system. Performed full system inspection including refrigerant level check via sight glass, verified all connections and components operating within normal parameters, and documented equipment condition with photos showing R-410A refrigerant lines and system components in serviceable condition.

Responded to water leak complaint with puddle forming on basement floor during AC operation. Upon arrival, found 26-year-old Heil air conditioning system with clogged condensate drain line causing water to overflow onto concrete floor. Cleared blockage from condensate tube using appropriate methods to restore proper drainage flow. Verified system cooling performance remained unaffected and operational. Tested drain line for proper water discharge and confirmed no further leakage occurring. System returned to normal operation with condensate draining correctly through cleared line.

Completed annual cooling maintenance and tune-up on residential AC system. Addressed customer concerns regarding existing Amana smart thermostat displaying inaccurate temperature readings in main room, with current reading showing 76° while cooling to setpoint of 72°. Inspected thermostat wiring installation and noted low-voltage cables routed through exposed wall cavity near floor transition area. Performed standard preventative maintenance procedures on cooling equipment and documented system operation with photos. Discussed thermostat replacement options with customer to resolve accuracy issues.

Responded to no cooling call on residential air conditioning system. Upon inspection, found drain pan with significant accumulation of dirt, debris, and moisture damage showing rust and surface deterioration. Documented equipment condition with photographs showing compromised drain pan integrity and evidence of long-term moisture exposure that could lead to system shutdown or water damage if left unaddressed.

Responded to service call for non-operational water softener system. Upon arrival, inspected Sterling brand water treatment system consisting of black brine tank and gray cylindrical softener tank with digital control head. Verified control unit was displaying error code 1155 on LCD screen. Performed diagnostic evaluation of system components including control valve, brine tank salt levels, and plumbing connections. Checked power supply to control head and tested programming settings. Examined water flow through inlet and outlet connections with white PVC piping. Reset system controls and cycled unit through regeneration process to restore proper operation. Confirmed water softener returned to normal functioning status before departure.

# Carrier Air Conditioner No Cooling - Capacitor and Wiring Repair Responded to service call for 10-year-old Carrier air conditioning system with complete loss of cooling affecting entire residence. Upon arrival, performed system diagnostics and visual inspection of outdoor condensing unit electrical components. Inspection revealed failed dual-run capacitor with visible deterioration and compromised wire connections. Further examination identified damaged brown wire conductor with burned and frayed insulation near capacitor terminal connection, indicating electrical arcing or overheating condition. Wire damage showed exposed conductor with heat-affected areas and compromised insulation integrity. Removed defective capacitor from electrical compartment and disconnected all associated wiring. Repaired damaged wire conductor by cutting back to undamaged section and installing new terminal connector. Verified all remaining wire connections for signs of heat damage or loose terminals. I

Responded to service call for non-operational air conditioning system. Upon arrival, conducted thorough inspection of residential HVAC installation located in basement mechanical room. System consists of gray metal furnace unit with associated water heater, copper refrigerant lines, and white PVC intake/exhaust venting. Performed diagnostic assessment of equipment to identify cause of cooling failure. Documented existing installation configuration including furnace positioning, ductwork connections, and venting arrangement. Photographed equipment layout and current system condition for estimate preparation. Provided customer with comprehensive estimate for necessary repairs to restore air conditioning functionality.

Responded to service call for loud noise complaint from HVAC unit at residential property. Upon inspection, identified excessive dust and debris accumulation on blower wheel assembly causing operational noise and imbalance. Cleaned blower wheel and squirrel cage fan, removing built-up debris from blades and housing, restoring proper airflow and eliminating noise issue.

Responded to no-cooling complaint on EnergiAir system installed last winter. Upon arrival, confirmed AC compressor not running when thermostat set to cooling mode. Inspected control board and found faulty relay preventing compressor contactor from engaging. Tested voltage at terminal blocks and verified proper 24V control signal from thermostat. Replaced defective relay on control board and confirmed all wire connections secure at terminal blocks. Cycled system through multiple cooling cycles to verify compressor operation and proper system function. Checked circuit breakers in main panel for proper connection and confirmed no tripping issues. System now cooling properly throughout home with compressor engaging on call for cooling.

Removed existing water treatment equipment from basement utility area and completed installation of new Sterling high-efficiency water softener system with integrated whole house sediment filter. Configured copper supply piping with brass compression fittings and mounted white sediment filter housing to concrete wall with proper inlet/outlet connections. System installed, tested, and left operational with all components properly positioned and secured.

Responded to no cooling complaint on 10-year-old residential air conditioning system. Upon inspection, found outdoor condensing unit housing severely compromised by extensive debris accumulation consisting of leaves, twigs, and decomposed organic matter surrounding electrical components and contactor assembly. Removed all debris from unit interior, cleared area around electrical connections and contactor, and restored proper airflow pathways. Verified all wire connections secure and contactor operational after cleaning. Unit returned to normal cooling operation.

Completed comprehensive 5-year tune-up on Generac standby generator system. Performed oil and filter change, documented oil plug service with 2-hour runtime verification, and inspected all refrigerant lines, electrical connections, and mounting hardware. All components found in proper working condition with orange service tags applied indicating next maintenance due date of 6-30-26, and generator plan renewed through 2025.

Completed annual cooling maintenance and tune-up on residential AC system. Installed new temperature sensor on main air handler unit, securing device to metal panel with proper wiring connections. Performed comprehensive system inspection and preventive maintenance procedures to ensure optimal cooling performance for the upcoming season.

Responded to no cooling complaint with fan operational. Upon inspection, found failed capacitor with visible corrosion and rust on terminals. Capacitor exhibited signs of age-related deterioration with oxidation present at connection points. Replaced defective capacitor with new unit, reconnected all electrical leads, and verified proper wire routing. Tested system operation and confirmed compressor engagement and normal cooling function restored. Unit returned to full operational status.

Completed annual cooling system maintenance and tune-up on residential air conditioning unit. Performed comprehensive system diagnostics including capacitor testing with digital multimeter, verified electrical connections, and inspected all major components. Unit operating within normal parameters; system cleaned and ready for continued service through 2029 warranty period.

Completed annual cooling maintenance on a 9-year-old Carrier 24ABB324A351 air conditioning system. Performed comprehensive tune-up including filter replacement, system inspection, and operational testing. Unit is factory charged with 3.15 lbs of R-410A refrigerant and operating within manufacturer specifications.