Top-Rated HVAC & Plumbing Services in Kalamazoo, MI

Responded to no-heat call for a 25-year-old furnace. Inspection revealed faulty electrical connection at terminal with degraded yellow wiring. Repaired connection, restored proper operation, and verified system functionality before completing service.

Identified and repaired a leaking outdoor spigot that was causing water infiltration into the home. Inspection revealed compromised copper pipe fittings at the 90-degree elbow connection, which were replaced along with the damaged brass valve assembly to restore proper function and prevent further water damage to the interior structure.

Replaced worn cartridge in shower faucet to address active leakage and water damage. Removed calcium deposits and mineral scaling from chrome handle and escutcheon plate. Tested water flow and verified complete resolution of the leak.

Performed scheduled complimentary furnace tune-up on EnergiAir WT 07-2034 unit (1 year old). Inspected electrical connections and drainage system, noting proper function of condensate pump with operational blue indicator lights. No issues identified during the comprehensive heating system evaluation.

Successfully installed a new water line for refrigerator, connecting from the existing residential plumbing system. Work included routing copper piping through utility area near water heater, ensuring proper fittings and connections to prevent leaks. Tested the installation to verify proper water flow and pressure to the refrigerator.

Completed quoted repair to replace shower valve in bathroom. Accessed plumbing through kitchen wall as recommended to avoid disturbing the older tile shower installation with rebar backing. Successfully installed new valve and verified proper operation of shower fixture.

Cleared kitchen sink drain blockage at U-joint, removing accumulated debris and restoring proper drainage. Inspected upstairs bathroom faucet drip issue, diagnosed worn cartridge requiring replacement to eliminate leakage.

Successfully installed a 40-gallon natural gas water heater with short configuration. Connected all necessary copper supply lines with appropriate brass fittings and installed proper ventilation ductwork with metal clamps to ensure safe operation. Verified all connections were secure and system was functioning correctly before completion.

Responded to home with post-fire restoration concerns regarding HVAC system making vibration noise, loud bangs during cycling, and insufficient heating. Inspected blower wheel assembly and found foreign debris adhered to wheel causing imbalance. Removed debris, tested system operation, and verified proper temperature rise and quiet operation after service.

Inspected 16-year-old furnace system in lower unit of duplex home that was only heating to 65°F despite owner's replacement of capacitor, thermostat, high limit switch, and filter. Examination of attic ductwork revealed significant air leakage at connections. Sealed duct joints and recalibrated system, restoring proper heating function to desired temperature.

Responded to service call for burst exterior spigot. Inspected basement shut-off valve and plumbing system serving the outdoor hose bib. Replaced damaged section of copper supply line and installed new frost-free sillcock with proper solder joints to prevent future freezing issues.

Successfully completed installation of new residential HVAC system, consisting of a high-efficiency furnace and addition of AC components. System was properly mounted in basement utility area with all necessary ductwork connections, electrical wiring, and condensate drainage established to ensure optimal performance and code compliance.

Performed annual heating service on furnace and humidifier. Discovered stagnant water in the humidifier reservoir with visible contamination and debris. Cleaned and serviced the drain pan to ensure proper drainage and system function.

Performed annual heating tune-up on 8-year-old Energi WT furnace with warranty through 01/2028. Inspected and cleaned condensate pump which showed signs of discoloration and moisture accumulation in the collection pan, and examined electrical components including circular contacts with multiple wire connections to ensure proper operation.

Diagnosed blower motor with suspected bearing failure in 2-year-old Carrier furnace (model WT 11-2028). Inspection revealed significant dust and lint accumulation on blower wheel affecting performance. Cleaned blower assembly and confirmed proper operation, extending component life while maintaining heating functionality.

Responded to customer report of burning smell from furnace vent. Upon inspection, discovered significant rust and corrosion on flexible metal ductwork, particularly along the corrugated sections. Determined that accumulated dust and debris on corroded areas were causing the burning odor when heated. Performed thorough cleaning of affected ducts and completed preventative maintenance tune-up to restore proper system operation.

Completed installation of customer-supplied kitchen faucet and utility sink replacement as quoted. Repaired two water line leaks and successfully installed a new laundry tub with faucet. All connections were tested and confirmed watertight with proper drainage.

Replaced heat exchanger (HTX) in Carrier furnace unit as quoted. Properly reconnected all electrical components including control board wiring and verified proper installation of PVC venting. System tested and restored to normal operation with no issues.

Diagnosed and resolved toilet flush issue by removing debris and mineral deposits from trapway and rim jets. Performed complete flush mechanism inspection and adjustment to ensure proper water flow and seal integrity. Toilet now functioning correctly without requiring plunging.

Performed annual heating maintenance on ENE-WT-3-2035 furnace. Replaced worn circular components showing signs of deterioration. Confirmed system is operating within normal parameters; no humidifier currently functioning on the unit.