HVAC, Plumbing & Generator Services in Allegan, MI

Completed furnace inspection and customer education visit on 7-year-old ICP heating system. Demonstrated proper filter replacement procedure and confirmed correct filter size of 16x25x1 for homeowner's future maintenance needs. System operating within normal parameters.

Completed annual cooling maintenance on 21-year-old Payne air conditioning system. Performed comprehensive tune-up including inspection of condenser unit, verified fan operation and protective grille integrity, assessed heat exchanger coil condition, and documented equipment status with photographic records. Unit found in operational condition with coils clean and free of debris; no immediate repairs required at time of service.

Completed annual cooling maintenance on 9-year-old Goodman air conditioning system. Inspected electrical components including dual-run capacitor (40/5 MFD) and CoreSense diagnostic module, verified all wire connections secure, checked condensate drain system with drip pan, and confirmed unit operational. All components functioning within normal parameters.

Conducted on-site evaluation for standby generator installation. Assessed existing electrical service panel to determine compatibility and capacity for generator integration. Documented current breaker panel configuration, including main disconnect location, available breaker spaces, and electrical load distribution. Panel inspection revealed clean, well-maintained load center with adequate labeling and circuit directory. Photographed panel interior and exterior to support equipment sizing recommendations and transfer switch placement planning. Evaluation will inform generator specification, transfer switch requirements, and installation scope for customer proposal.

Responded to no-heat call for two 18-year-old furnaces at residential property. First unit was completely unresponsive with no power to control board; second unit had power but failed to ignite. Performed diagnostic testing on both Comfort-Maker furnace systems, inspecting blower motor assemblies, electrical connections, gas valve operations, and ignition components. Documented existing conditions of both units including PVC condensate drainage, flexible conduit routing, and internal cabinet components through photographic evidence for customer records.

Responded to reduced airflow complaint affecting upstairs vents. Upon inspection, discovered severely damaged flexible ductwork in attic space with torn outer jacket and compromised insulation, causing significant air leakage and loss of conditioned air delivery to upper level registers. Documented existing conditions with photos showing deteriorated duct sections requiring replacement to restore proper system performance.

Conducted on-site assessment for conversion from electric range to gas cooking appliance. Evaluated existing kitchen layout with current electric stove installation and identified utility closet location containing HVAC equipment and mechanical systems. Documented routing requirements for new gas line installation from utility area to kitchen cooking surface, assessed wall penetrations and pathway logistics, and provided comprehensive project estimate for gas line installation and appliance conversion.

Completed full HVAC system installation including new furnace unit in basement mechanical room, outdoor condensing unit on concrete pad with proper electrical disconnect, and ductwork modifications. Installed white PVC venting for furnace exhaust and intake, connected metallic supply ductwork, and positioned exterior AC unit on level concrete pad with decorative rock surround. All equipment properly labeled, electrical connections completed per code, and system tested for operational functionality.

Conducted sales estimate for furnace and air conditioning system replacement due to existing furnace malfunction. Assessed electrical service panel capacity and condition in basement utility area to determine compatibility with new HVAC equipment installation requirements. Documented existing electrical infrastructure including circuit breaker panel configuration and available amperage for future system upgrades. Provided comprehensive estimate for complete furnace and AC system replacement with recommendations based on current equipment failure and electrical service evaluation.

Responded to no heat/no cool call on 2003 Bryant system where Amazon smart thermostat display went blank and lost communication with equipment. Upon arrival, found thermostat had failed and was unable to control furnace or air conditioning unit. Removed failed smart thermostat from wall plate and inspected existing low-voltage wiring connections. Verified proper wire terminations at thermostat base including R, W, Y, G, C, and O/B terminals. Confirmed 23-year-old Bryant furnace was otherwise operational and that loss of HVAC function was isolated to thermostat failure. System restored to proper operation.

Completed full furnace installation in residential basement utility area. Installed air handler unit with proper mounting and secured all electrical connections including control board module. Ran and secured PVC condensate drain lines with appropriate coupling joints and primer application. Verified all safety labels and documentation are visible and properly affixed to equipment. Connected ductwork and completed all wiring terminations. Obtained and documented customer identification for financing records. System installation complete and ready for operation.

Completed annual heating and cooling maintenance including furnace, air conditioning, and humidifier tune-up on two-year-old equipment. Performed comprehensive system inspection, verified proper operation of all HVAC components, checked refrigerant levels, cleaned condensate lines, replaced filters, and documented equipment condition with photos of accessible mechanical spaces showing ductwork, plumbing infrastructure, and insulation integrity.

Responded to recurring no-cooling complaint on 3-year-old EnergiAir unit. Upon inspection, discovered severely corroded copper refrigerant line with significant oxidation and green verdigris buildup at connection joints, indicating long-term moisture exposure and deterioration. The extensive corrosion at pipe fittings was identified as the root cause of the chronic cooling failure. Documented the failed components with photographs showing compromised pipe integrity and recommended complete refrigerant line replacement to permanently resolve the ongoing cooling issues that have required multiple service calls.

Completed annual cooling maintenance on Amana condenser unit as part of 2-year EnergiAir maintenance agreement. Inspected indoor air handler components in utility space, including transformer, electrical connections, and condensate drainage system. Performed exterior condenser inspection, verified proper operation of unit, checked refrigerant lines and electrical disconnect, and documented equipment condition with photos.

Completed annual cooling maintenance on EnergiAir system per 4-year service agreement. Performed comprehensive tune-up including filter inspection, refrigerant level check, electrical connection verification, condensate pump operation test, and overall system performance evaluation. All components including condensate drainage system and associated wiring found operating within normal parameters; unit ready for cooling season.

Completed three-year tune-up maintenance on Generac generator unit, including oil and filter change as documented by photos showing new orange oil filter with date notation installed on engine assembly. Observed evidence of minor fluid residue on pad beneath unit during service, which was noted for monitoring. All routine maintenance items performed according to manufacturer specifications, and unit tested successfully upon completion.

Responded to service call for on-demand tankless water heater experiencing intermittent failure to ignite at specific fixtures while operating normally at others. Performed diagnostic inspection of wall-mounted tankless unit, removing front access panel to examine internal components including heat exchanger, control board, wiring connections, and gas supply lines. Verified proper electrical connections, inspected circuit board for signs of failure, and checked all wire harnesses for loose connections or corrosion. Examined copper piping and gas line connections for restrictions or issues affecting flow sensing. Tested unit operation at multiple fixtures throughout the property to replicate reported intermittent ignition problem. Documented findings with photographs of internal components and installation environment for reference. Homeowner noted unit age unknown, having been in place at least five years prior to current ownership, which may contribute to component wear affecting flow

Completed annual cooling system maintenance on 16-year-old AC unit located in attic space. Performed standard tune-up procedures including inspection of condensate pump and drain line assembly, verified proper operation of all mechanical components, and documented equipment condition with photos. All systems tested and found operating within normal parameters.

Responded to emergency drain backup affecting multiple fixtures including toilet, bathtub, and sink. Upon inspection, identified main sewer line obstruction causing wastewater to back up through lower-level plumbing fixtures. Successfully cleared blockage using professional drain cleaning equipment, restoring proper drainage flow throughout the system. Verified all fixtures were draining correctly upon completion and advised customer on preventative maintenance measures.

Excavated trench to access and install red flexible conduit piping from outbuilding to main structure. Trench depth measured and verified, conduit laid and secured along trench bottom, with excavated soil staged for backfill upon completion.