HVAC, Plumbing, and Electrical Experts in Byron Center

Installed a new laundry tub sink in the laundry room and connected it to the existing drain and supply plumbing. Verified the drain tie-in to the existing PVC waste line, secured the flexible drain connections, and confirmed proper flow with no leaks at the fittings.

Performed a standard flush on a Bradford tank-style water heater that had never been serviced, draining and flushing the tank to remove accumulated sediment. Inspected the burner assembly through the combustion chamber sight port and confirmed a stable blue flame indicating proper combustion. Unit was returned to service operating normally with no performance concerns noted.

Inspected the non-cycling water softener and found the brine tank holding cloudy standing water, indicating a brine system or regeneration fault, and serviced the unit to restore cycling. Also evaluated the burst feeder line to the exterior spigot, which was accessible and exposed, and addressed the pipe for repair or replacement.

Installed a new Carrier upright gas furnace in the basement, connecting it to the existing supply ductwork and trunk line, gas supply piping, electrical and control wiring, and flue venting. Installed a condensate pump for drainage and verified all connections and system components were secure and properly configured for operation.

Performed a Furnace Super Tune-up on a 15-year-old gas furnace and identified a compromised heat exchanger during inspection, presenting a potential carbon monoxide hazard. Shut off the gas and electrical supply to the unit, tagged the gas line with a red-tag notice documenting the heat exchanger condition, and reviewed the warning and safety findings with the homeowner, who acknowledged them in writing. The furnace remains out of service pending repair or replacement.

Performed annual heating maintenance on the furnace, including a complete tune-up and inspection of operating components. Inspected the Aprilaire Model 60 automatic humidifier control, confirmed proper operation with the humidistat set to approximately 3 and the indoor humidity reading displaying correctly, and verified low-voltage wiring connections were intact with no visible damage. System was left operating normally.

Installed a new 40-gallon tall natural gas Bradford White water heater in a drain pan, with new copper water connections, brass shutoff valves, and a gas line connection. Connected the vent to the existing flue and verified proper draft and a leak-free installation. The unit is operating normally with no signs of leaks, rust, or damage.

Responded to a no-heat call on a 17-year-old Bryant forced-air furnace and inspected the blower compartment and control board. Found heavy rust and mineral corrosion on the cabinet bottom pan and water-staining on the blower housing interior, indicating prolonged moisture exposure or a leak, along with dirt and residue buildup on the blower wheel and cabinet. Documented findings with photos; repair recommendations were provided on site.

Responded to a no-hot-water complaint on a 10-year-old Bradford White tank water heater in the basement, accessing the unit through a congested storage area. Photos documented the surrounding conditions, including damp, discolored concrete floor patches and staining on the overhead OSB deck near the water and venting lines. Specific diagnostic findings and repair actions were not recorded in the available details, so the cause of the no-heat condition and any corrective work should be confirmed with the technician before this entry is finalized.

Performed annual heating tune-up on Carrier gas furnace with whole-home humidifier. Removed lower blower compartment access panel and discovered a significant accumulation of nesting debris (pine needles, plant fibers, and insulation-type material) on the cabinet floor adjacent to the blower assembly and wiring harness. Removed all debris and cleaned the compartment to restore proper airflow and eliminate fire and wire-damage hazards. Inspected the blower motor, gas valve, wiring, and condensate/vent piping, and verified the humidifier was in good working order. Reinstalled the access panel and confirmed the furnace was operating normally.

Performed annual furnace tune-up, including inspection and cleaning of the furnace and the whole-house humidifier. Removed the humidifier cover and drained the water pan, which contained stagnant water and sediment buildup, then cleaned the pan and components to restore proper drainage and operation. Verified the system was operating correctly at completion.

Performed an on-site estimate for furnace replacement on a club member's system following a failed heat exchanger diagnosis. Inspected the gas-fired furnace, flue/venting connections, and adjacent water heater in the basement utility area, noting foil-taped repairs on the galvanized flue piping, and documented existing equipment conditions with photos to support the replacement proposal.

Performed a full furnace tune-up on a 21-year-old Bryant unit, inspecting the blower assembly, cabinet interior, and wiring. Found significant rust and corrosion with standing moisture in the lower cabinet pan, along with water staining near the blower housing and frayed duct insulation, indicating a moisture source that should be traced (condensate drain, coil, or humidifier) and the corroded components monitored for failure.

Removed and replaced the existing furnace and air conditioning system, installing a new gas furnace with matched evaporator coil in the basement and a new outdoor condenser on a level concrete pad. Connected refrigerant lines, condensate drain piping, PVC combustion venting, ductwork, and the electrical disconnect, and reconnected the whole-house humidifier. System was verified clean and intact with no visible damage, and financing paperwork was completed and activated.

Responded to complaint of insufficient hot water delivery to fixtures in residential property with two-year-old Navien tankless water heater system. Upon inspection, found dual heating units with hydronic manifold configuration and complex copper piping distribution system. Evaluated system pressures using existing gauge, checked all ball valves and zone controls for proper operation, and verified expansion tank functionality. Inspected burner assemblies and internal components of both units with panels open to assess combustion efficiency and heat exchanger condition. Examined copper pipe routing and connections throughout the manifold system to identify any restrictions or flow issues affecting hot water distribution. Verified proper venting through corrugated flexible tubing connections. Adjusted system parameters and confirmed adequate hot water flow to all fixtures upon completion.

Completed installation of new zone damper assembly in attic HVAC system. Accessed existing ductwork, mounted replacement damper assembly with electrical connections, and secured all components to ensure proper zone control operation. System tested and verified operational upon completion.

Completed full HVAC system installation including new furnace and air conditioning condenser unit. Installed furnace in basement mechanical room with proper clearances and ventilation requirements, connected silver ductwork to existing distribution system, and integrated with PVC drainage piping. Mounted outdoor AC condenser unit on concrete pad against exterior wall with protective top grille, verified proper refrigerant line connections between indoor and outdoor components. All equipment labeled with manufacturer specifications, system tested for proper operation, and installation meets code requirements for residential heating and cooling applications.

Successfully installed a new unit heater system in the attic space. Installation included mounting the unit heater between floor joists, running electrical wiring (black and white conductors) through the wall cavity to power the unit, and connecting necessary ductwork with flexible ducting routed through the attic structure. Applied spray foam insulation at penetration points to seal gaps and prevent air leakage around the installation area. All work completed to manufacturer specifications with proper electrical connections and structural support utilizing existing roof trusses and floor joists.

Completed annual heating maintenance on 11-year-old EnergiAir furnace and humidifier system. Performed standard inspection, cleaning, and safety checks. Documented system components with photos showing humidifier water panel filters and related hardware for maintenance records.

Responded to no hot water call for tank-type water heater in basement utility area. Upon arrival, found unit to be approximately 15+ years old, predating customer's 2012 occupancy. Performed diagnostic inspection of water heater and associated plumbing connections, including examination of gas supply lines, water inlet/outlet piping, temperature and pressure relief valve, and electrical components. Noted this unit differs from the Bradford White model previously on file in system records. Documented equipment condition and configuration with photographs showing copper supply piping, black insulated lines, and overall installation layout. Verified electrical panel location around corner from water heater for reference. Unit assessed as aged beyond typical service life expectancy for residential tank water heaters.