Dedicated Heating, Cooling, Plumbing, and Electrical Services in Cedar Springs

Purged trapped air from the in-floor radiant heating loops at the manifold and zone valve assembly, restoring proper hydronic circulation and heat distribution. Verified flow through the loops and confirmed the zone valves, isolation valves, and associated piping were operating correctly after the purge.

Installed a new high-efficiency upright gas furnace on a drain pan in the basement utility area, with PVC intake/exhaust venting routed overhead and connected to a galvanized supply plenum and existing ductwork. Completed electrical connections via flexible conduit, labeled the plenum, and verified the installation showed no visible damage or defects.

Performed a full tune-up on a 9-year-old furnace, including removal and inspection of the burner assemblies, which showed oxidation and soot buildup from heat exposure. Used a borescope to inspect the heat exchanger, noting minor surface rust and pitting along the weld seam, with no evidence of cracking or perforation. Cleaned the burners and verified safe, efficient operation.

Responded to service call for water heater replacement estimate. Customer reported that their existing 40-gallon short water heater was causing basement flooding when running water. Conducted on-site inspection and photographed the existing Bradford White water heater installation in the basement utility area. Evaluated current unit's condition, plumbing connections including copper supply lines, brass fittings with red-handled valves, pressure relief components, and metal flue ventilation system. Assessed surrounding basement infrastructure including exposed wall framing, concrete flooring, and available clearances for replacement unit installation. Provided comprehensive estimate for replacing the failing 40-gallon short water heater with appropriate new unit to resolve flooding issue.

Completed scheduled generator tune-up on 5-year-old Generac unit. During inspection, identified significant corrosion on metal piping and documented cracked generator base requiring future attention. Performed routine maintenance procedures, verified all mechanical and electrical components, and documented equipment condition with photos for customer records.

Completed warranty replacement of residential furnace unit with new Amana furnace system. Installation included proper venting with PVC piping, connection to existing ductwork, and verification of all system components. Unit tested and confirmed operational upon completion.

Conducted on-site evaluation for furnace replacement estimate in single-family residence with approximately 20-year-old heating system. Inspected existing electrical panel and circuit breaker configuration to assess compatibility and capacity for new furnace installation. Documented electrical infrastructure, including main breaker panel with labeled circuits and available spaces for potential electrical modifications required for equipment upgrade.

Completed annual heating maintenance on a 9-year-old EnergiAir furnace system. Performed comprehensive tune-up inspection, verified all operational parameters, and documented system condition with photos. Unit operating properly with no humidifier present; warranty coverage extends through August 2027.

Responded to generator lockout condition caused by multiple start attempts. Upon arrival, found unit in safety lockout mode after client attempted manual restart procedures. Performed system diagnostics and reset lockout sequence. Inspected fuel supply lines, valve operations, and mechanical components for proper function. Verified all safety interlocks and control circuits were operating within normal parameters. Cleared fault codes from control board and restored generator to operational status. Educated client on proper startup procedures and importance of allowing automatic control sequences to complete without manual intervention. Unit tested successfully and returned to standby mode ready for automatic operation.

Successfully installed 14KW Kohler standby generator with 200A service integration. Coordinated utility disconnect and reconnect services, secured electrical and mechanical permits, and completed all required inspections including gas pressure testing. Installation included proper gas line connections with pressure gauge assembly, electrical transfer switch integration, and final system commissioning with inspector approval.

Completed annual cooling system maintenance on 22-year-old Fraser-Johnston air conditioning unit. Performed comprehensive tune-up including system inspection, component cleaning, refrigerant level verification, electrical connection checks, and operational testing. All components functioning within manufacturer specifications; system operating efficiently for continued cooling season performance.

Successfully completed furnace installation in basement utility area. Installed horizontal air handling unit with proper drainage system using white PVC piping with multiple bends and connections, mounted ductwork including silver-colored supply ducts, and completed all electrical connections. System tested and verified operational upon completion.

Responded to no-heat call on 20-year-old Lennox furnace. Upon inspection, found extensive rust and corrosion throughout critical mechanical components, including blower assembly mounting brackets, connecting joints, and fittings. Corrosion was severe enough to compromise structural integrity and safe operation of the unit. Documented deteriorated condition with photographs showing oxidation on metal surfaces, corroded mounting hardware, and aging internal components. Due to the age of the equipment and extent of deterioration observed, recommended full system replacement as the most cost-effective and safe solution rather than attempting repairs on compromised components.

Responded to service call for leaking kitchen faucet in residential property. Upon inspection, identified active leak at faucet base with visible water damage and staining in cabinet below sink, indicating ongoing moisture issue. Disassembled chrome single-lever faucet assembly, replaced worn internal cartridge and deteriorated O-rings causing the leak. Cleaned and reassembled faucet components, tested water flow and spray nozzle function, confirmed leak elimination with no dripping at base or connections. Verified all supply line connections under sink were secure and dry upon completion.

Completed annual heating maintenance on furnace system per club membership agreement without humidifier service. Performed comprehensive tune-up including inspection of blower motor assembly, burner components, and gas valve operation. Verified all electrical connections, wire terminations, and safety controls functioning properly. Documented system condition with photographs showing internal mechanical components and blower assembly. Unit covered under equipment warranty extending through March 2032. All systems operational and ready for heating season.

Replaced washing machine cold water supply hose with customer-provided hose at basement laundry connection point. Shower drain replacement on fiberglass unit was addressed as requested to resolve drainage issue.

Completed comprehensive plumbing system upgrades including replacement of sewage ejection pump system with new pump, check valve, and sealed lid. Installed X-Tall Kohler comfort height elongated toilet in downstairs bathroom. Replaced existing well tank with new 44-gallon pressure tank to improve water pressure throughout the home. Installed new brushed nickel bathroom faucet to ensure optimal water flow and pressure delivery. All components tested and confirmed operational upon completion.

Responded to emergency service call for non-operational sump pump with reported sewage odor and slow-draining lower level toilet. Upon inspection, found sump pump basin with PVC discharge piping and confirmed pump failure. Assessed mechanical room conditions and identified moisture accumulation around pit area indicating drainage issues. Inspected affected bathroom fixture and verified sluggish flush performance consistent with potential drainage obstruction or pump system malfunction. Documented equipment conditions including basin configuration, discharge piping with blue valve assembly, and surrounding utility area. Evaluated correlation between non-functioning sump pump and compromised toilet drainage, determining pump failure was impacting overall lower level plumbing system performance.

Completed annual cooling maintenance on 31-year-old Amana air conditioning system. Performed comprehensive tune-up including system inspection, cleaning, and operational testing. Documented crawlspace conditions showing PVC condensate drain line with accumulated dirt and debris on concrete floor surface, along with evidence of moisture accumulation in utility area beneath unit.

Completed annual cooling maintenance on a 20-year-old Lennox system with a 2017 condenser motor located in crawlspace. Inspection revealed significant water accumulation, sediment buildup, and biological growth in the condensate drain pan, indicating potential drainage issues. Documented system condition with photos showing standing water and debris requiring attention to prevent future overflow or secondary pan failure.