Heating, Cooling, Plumbing & Generators in East Lansing MI

Responded to a no-heat call on a furnace and inspected the unit's condensate drain assembly, including the PVC drain line, rubber coupling with stainless clamps, and trap/branch fittings. No visible leaks, blockages, damage, or corrosion were found at the drain components, and the surrounding area was left clean and orderly.

Performed on-site evaluation of an exterior hose bib and backflow preventer assembly to assess relocation of the outside faucet line to facilitate irrigation system drain-down. Inspected the existing brass backflow preventer with dual ball isolation valves, noting a weathered, tarnished supply line alongside newly installed copper piping with a tee fitting and hose-bib outlet. Documented existing conditions with photographs and evaluated routing options to establish scope of work for the proposed relocation.

Responded to a clogged basement drain and assessed the drain line, where the aging cast iron/copper stack connects via a rubber coupling to PVC fittings and a horizontal drain run. Evaluated the piping for replacement per the customer's request, and the affected drain section was addressed to restore proper flow.

Inspected the humidifier supply line from the water heater and located the leak at the chrome angle stop valve and compression connection, which showed tarnishing, residue, and discoloration consistent with a slow weep. Isolated the water supply using the in-line 3/4" brass ball valve, serviced the angle stop and compression fitting feeding the Aprilaire humidifier's copper supply tube, and restored water service. Verified no remaining leaks at the tee, valve, or tubing connections.

Located and repaired the leak at the kitchen faucet by inspecting the supply connections and replacing the worn components to restore a watertight seal. Cleared the slow drain in the upstairs shower by removing the strainer and clearing the accumulated hair and debris from the drain line, restoring proper flow. Tested both fixtures under running water and verified no leaks and normal drainage.

Performed annual heating tune-up on a 24-year-old Nordyne furnace, including inspection of the electrical connections, wiring, and condensate drain line and trap. No humidifier is installed on the system. Unit was left operating normally.

Responded to a no-heat call on a newly installed furnace and AC system with the thermostat displaying a "call for service" message. Inspected the cabinet wiring and found loosely arranged line-voltage conductors at the junction box bracket, including a conductor with nicked insulation and evidence of scorching near the bracket flange. Repaired and secured the damaged wiring and wire-nut connections, restored proper power to the unit, and verified normal operation and thermostat communication.

Performed annual heating maintenance on the boiler, including a complete tune-up and operational inspection. Used an inspection camera to examine the heat exchanger and documented heavy fin soiling, rust staining, and scale deposits that warrant monitoring and cleaning. Renewed the customer's recurring service agreement coverage for the boiler, air conditioning, and air handler.

Completed a half-day of quoted repairs on the spa, including servicing the equipment compartment housing the control pack, pump, and heater assembly. Inspected and addressed wiring connections and aged components in the tight, debris-filled cabinet, and verified the dedicated breaker panel circuit labeling and protection for the spa supply.

Completed full system replacement, installing a new gas furnace and matching air conditioning condenser. The outdoor condenser was set on a level concrete pad and connected to the line set, electrical disconnect, and flexible conduit. The installation was finished with the equipment secured and the surrounding area left clean and free of visible damage.

Installed a new 75-gallon natural gas Bradford White tank-style water heater, connecting the copper supply lines with brass shutoff valves and routing the galvanized flue to the existing overhead vent. Connected the temperature and pressure relief valve discharge piping, and verified the unit is clean, properly secured, and free of visible leaks or damage.

Installed a new upright high-efficiency gas furnace with supply plenum and galvanized ductwork connections, including PVC combustion venting, condensate drain piping, and a flexible gas line connection. Mounted and connected an AprilAire humidifier to the plenum with a dedicated water supply line, and posted the service log sheet on the ductwork for future maintenance records. Completed the installation with a clean, code-compliant mechanical layout and no visible damage or leaks.

Performed a camera inspection of the shower drain line following a previous clog to verify the obstruction was fully cleared. Inspected the accessible PVC trap and drain piping beneath the floor joists, confirming the line is flowing freely with no remaining blockage or visible restrictions.

Repaired a separated ductwork seam near the furnace by realigning the duct sections and sealing the joint with foil-faced HVAC tape to restore a secure, airtight connection at the transition fitting. Inspected adjacent duct connections and fasteners for additional leaks or loosening and confirmed the repair was stable and properly sealed.

Installed a new chrome single-handle gooseneck faucet on the center deck plate of the double-basin stainless steel kitchen sink, securing the mounting hardware and connecting the hot and cold supply lines. Tested for proper operation, flow, and temperature control, confirmed no leaks at the connections, and verified drainage at both basins.

Completed installation of new toilet in powder room featuring herringbone brick flooring and beadboard wainscoting. Removed existing fixture, installed new two-piece porcelain toilet with chrome flush lever and water supply line, ensuring proper sealing and connection to existing plumbing. All work completed as quoted with customer satisfaction confirmed.

Completed annual heating maintenance inspection on 19-year-old Bryant furnace system without humidifier. Performed comprehensive fall checkup including visual inspection of equipment, verified proper operation of all components, and documented system condition with photographs. Unit operating normally with no immediate concerns noted; last combustion analysis performed in 2022.

Completed annual heating maintenance on 13-year-old Bryant furnace system. Performed comprehensive tune-up including inspection of all mechanical components, burner assembly, heat exchanger, blower motor, and electrical connections. Confirmed humidifier is not in service per customer request and documented current system condition with photos of equipment and installation.

Completed installation of a 40-gallon Bradford White natural gas water heater, model RG240S6N, with a 40,000 BTU/hr input rating and 151.1-gallon first hour capacity. The unit was installed as a short configuration natural draft Category I appliance, meeting ASHRAE Code 90 efficiency requirements and all manufacturer-specified clearances for closet installation. All gas connections, venting, and safety controls were properly configured and tested per code requirements.

Successfully completed installation of wall-mounted tankless water heater unit in utility area. Installed unit on plywood backing board secured to concrete block wall, connected copper supply and discharge piping with appropriate fittings and isolation valves, installed metal drip pan beneath unit for leak protection, and verified all connections for proper operation. Digital control panel programmed and Energy Star certified unit tested to ensure optimal performance and hot water delivery throughout the system.