Exceptional HVAC, Plumbing & Generator Services in Howell, MI

Replaced a damaged kitchen faucet with a broken spout at the base by removing the failed unit and installing a new brushed-nickel high-arc faucet on the double-basin stainless steel sink. Secured the faucet to the deck, connected the supply lines, and verified proper operation of both lever handles and the side sprayer, with no leaks at connections and normal drainage from both basins.

Completed comprehensive tune-up service on 15-year-old Generac generator unit. Performed standard maintenance inspection including examination of engine components, carburetor assembly, fuel system connections, and internal electrical connections. Documented equipment condition with photos showing engine compartment and control panel assembly with valve service notation dated 3-6-06. Unit operational at time of service completion.

Completed warranty repair on HVAC blower wheel and housing assembly. Accessed air handler unit and addressed blower component issues, with photographic documentation showing significant condensation and frost buildup on internal metallic components indicating prior airflow or mechanical problems. Successfully replaced defective blower wheel/housing assembly, restoring proper system operation and airflow.

Conducted on-site assessment for Kohler generator installation. Evaluated existing electrical service entrance, meter configuration, and main panel location to determine optimal placement and connection requirements for standby generator system. Documented current electrical infrastructure including service conduit routing, exterior disconnect provisions, and interior panel accessibility for transfer switch integration planning.

Responded to water pressure complaint following recent water heater installation. Upon inspection, identified issue related to pressure tank system in basement utility area. Verified Champion by Amtrol pressure tank connections, checked valve operation at tank base, and confirmed proper system pressurization to restore adequate water pressure throughout residence.

Responded to recurring leak issue on 1.5-year-old Lochinvar boiler system where water was running through a heating zone. Inspected copper piping and zone valves in basement area, identified source of intermittent water flow problem, and performed necessary repairs to resolve the recurring condition. Documented system with photos and verified proper operation of all zones upon completion.

Conducted comprehensive sales estimate for furnace and air conditioning system replacement. Evaluated existing electrical infrastructure including main service panel and circuit capacity to ensure compatibility with proposed HVAC equipment. Documented current electrical configuration, panel condition, and available circuit breaker spaces to determine if electrical upgrades would be required for new system installation. Assessed utility area access, clearances, and structural considerations for equipment placement. Provided detailed estimate covering complete furnace and AC system replacement with specifications matched to home requirements.

Completed annual tune-up and maintenance on Generac standby generator. Performed comprehensive inspection of engine components, verified proper operation of all mechanical systems, checked fluid levels and connections, and tested electrical components. All systems inspected and found to be operating within normal parameters; unit is in good working condition with no issues identified.

Completed annual heating maintenance on Carrier furnace system. Performed comprehensive tune-up including inspection of heat exchanger, burner assembly, and ignition components. Discovered standing water and moisture damage in condensate drain pan with visible staining and sediment buildup. Inspected condensate drainage system including PVC drain line and verified proper slope and connections. Cleaned drain pan and removed debris. Tested blower motor operation, checked amp draw, and verified proper airflow. Inspected gas connections for leaks, tested safety controls, and confirmed proper furnace cycling. System operational upon departure with recommendations provided for condensate drainage monitoring.

Responded to a non-functional exterior hose bib where the valve handle would turn but no water was dispensed. Successfully replaced the defective hose bib assembly with a new frost-free sillcock, accessing the connection point through the attic space where copper supply lines transition to the exterior fixture. The new installation was properly secured to the exterior wall within the existing recessed mounting box and all connections were tested to ensure proper water flow and operation.

Responded to customer concern regarding significant increase in energy consumption from two residential AC systems compared to previous cooling season. Performed diagnostic evaluation on both units: 11.5-year-old Goodman system serving basement level and 10-year-old Goodman system serving first floor. Inspected outdoor condenser units, refrigerant line sets, and service valves. Documented equipment condition and installation environment with photographic evidence showing condenser placement, surrounding clearances, and refrigerant service connections. Customer advised to monitor system performance and energy usage patterns for further assessment.

Responded to plumbing leak emergency in basement where water distribution system splits to two meters. Repaired leaking copper union connection at the split point, addressing significant corrosion and oxidation on aged copper piping. Additionally, repaired leaking elbow joint on exterior where plumbing transitions from house through wall to outdoor system, ensuring proper seal and connection integrity at the penetration point. Both leaks were stopped and system restored to proper operation.

Responded to emergency service call for downed electrical mast. Upon arrival, found existing meter base and emergency disconnect panel mounted on exterior wall with gray PVC conduit extending upward. Inspected weatherhead and service entrance conductors for damage from mast failure. Documented existing water damage and staining on siding between meter and disconnect panel, indicating previous moisture infiltration. Evaluated vertical conduit mounting and bracket integrity along building exterior. Photographed current installation showing digital meter, emergency disconnect box with proper labeling, and conduit routing. Assessed weathering patterns and dark streaking on vinyl siding suggesting long-term water runoff from roofline. Examined soffit area where service entrance cables enter structure, noting cable condition and support. Verified proper grounding and bonding connections at meter base. Restored electrical service safely and confirmed system operational.

Responded to plugged toilet that could not be cleared with standard plunger or snake methods. Assessed the blockage and determined that conventional clearing techniques were insufficient to resolve the obstruction. Further diagnostic work or specialized equipment was required to address the severe clog in the toilet drain line.

Completed annual cooling maintenance on 10+ year old Amana air conditioning system. Performed comprehensive tune-up including system inspection, refrigerant line assessment, and component evaluation. Photographed outdoor condenser unit showing weathered refrigerant line couplings with deteriorated coating requiring monitoring for potential future service needs.

Completed electrical estimate for new construction residential property requiring additional outlet installations in main dwelling and detached shed. Assessed basement utility room with exposed insulation and laundry fixtures, as well as exterior foundation area with existing electrical infrastructure including dryer vent. Documented existing conditions and electrical access points to determine optimal routing for new circuit installations and outlet placement throughout the property.

Completed electrical estimate for installation of new 120V receptacle outlet in basement approximately 20-25 feet from main electrical panel. Assessed existing spray foam insulated utility space with exposed ceiling joists and determined optimal routing path for conduit installation to power new outlet location while maintaining code compliance.

Returned to complete warranty repair on condenser coil. Replaced oxidized condenser coil assembly showing significant corrosion on copper refrigerant lines and deteriorated aluminum fins due to extended weather exposure. Unit tested and operational upon completion.

Responded to no cool complaint on refrigeration unit. Upon inspection, found evidence of frost accumulation on refrigerant lines and connections, indicating potential restriction or low refrigerant charge. Documented internal components showing moisture and ice formation on evaporator connections. Unit unable to maintain set temperature due to compromised cooling capacity.

Responded to no heat call at single family residence. Upon arrival, located furnace and performed diagnostic inspection. Discovered significant moisture damage and deterioration to building materials and insulation surrounding furnace area. Evidence of long-term water intrusion with visible rust-colored staining, mold growth, and material degradation throughout insulation and adjacent surfaces. Documented extensive damage with photographs showing compromised insulation integrity and structural concerns. Advised customer of moisture damage findings and potential safety hazards related to furnace operation in current environment. Recommended immediate remediation of water intrusion source and replacement of damaged insulation materials before furnace can be safely serviced or repaired.