Top-Rated HVAC & Plumbing Services in Kalamazoo, MI

Responded to no-heat complaint on 11-day-old warranty furnace that would not engage despite customer reset attempts. Upon inspection of the basement utility area, identified and corrected issue with the furnace ignition system, restoring proper heating function to the unit.

Responded to no heat call and identified severely restricted airflow due to heavily clogged filter/component with extensive dust and lint accumulation. Removed and cleaned the obstructed component, inspected the interior compartment for proper operation, and verified system functionality before completing service.

Responded to no-heat call for 12-year-old Concord furnace blowing cold air. Upon inspection, found faulty blower motor assembly causing system failure. Replaced defective component, verified proper ignition sequence and heat output. System now functioning correctly.

Responded to no heat call for 0-year-old Energy Waste furnace (model 01-2036). Inspection revealed significant water intrusion in the basement/crawlspace with standing water near the furnace area. Determined that moisture has damaged the furnace components, preventing proper operation. Recommended professional water remediation before furnace repair/replacement can be safely performed.

Responded to service call for a Honeywell generator (model WT 5-2027) with a gas line leak at connection point. Inspected the Chicago Fittings Corporation gas line component (part IR-270) where it enters the ground. Repaired leak at connection point to ensure safe operation of the standby home generator system during winter conditions.

Installed Sterling Water Softener System (30,000 Grain SWS1-30) in utility area. Completed all necessary plumbing connections including integration with existing water lines. System was properly configured, tested for functionality, and verified to be operating according to manufacturer specifications.

Performed annual heating maintenance on EnergiAir furnace (model WT 04-2030, manufactured 2017). System appears well-maintained with proper ventilation and drainage connections. No humidifier present. Completed standard tune-up procedures and documented system condition with photographs.

Responded to a call for a leaking galvanized T-fitting in utility room. Discovered significant water damage and mold on walls surrounding the utility sink. Inspected PEX and copper supply lines in wall access panel. Provided client with information on water softener options as requested.

Completed annual heating service on 12-year-old ICP furnace. Inspected gas valve, control assembly, and electrical connections for proper operation. System shows normal operational wear but remains in functional condition with no immediate concerns identified.

Successfully completed quoted repair service for shower valve replacement and water heater flush. Removed existing shower control valve assembly and installed new components to address leaking issues. Performed comprehensive water heater flush to remove sediment buildup and restore optimal operation.

Completed quoted repair job involving replacement of upstairs kitchen water supply lines and PVC drain pipes in a residential property. Work included installation of new PVC drainage components and water supply lines, properly secured with metal brackets to floor joists in the basement/crawlspace area. All connections were tested to ensure proper function and absence of leaks.

Completed annual heating maintenance on 6-year-old Carrier furnace and humidifier system. Inspected blower motor bearings as previously noted during AC service in August 2024, finding them in acceptable operating condition. System is functioning properly with all components tested and verified operational.

Investigated and resolved rattling/banging noise issue in recently installed Liberty 405 pump system. Secured loose PVC piping connections and added vibration dampening at key junction points to eliminate water hammer effect during pump shutdown cycle. System now operating quietly and efficiently under warranty service.

Responded to service call for bathtub faucet leak occurring during water operation. Inspected recently replaced faucet assembly and discovered improper diverter valve seal. Replaced faulty valve components and applied proper thread sealant to connections. Tested water flow at all settings with no leakage observed after repair.

Diagnosed no heat issue on 6-year-old EnergiAir furnace (Model WT 04-2031). Identified faulty control board causing system failure to heat or cool. Replaced control module and verified proper system operation through complete heating cycle test.

Completed annual heating maintenance service on furnace and humidifier per scheduled recurring service agreement. Performed thorough inspection of electrical components and connections. System is operating within normal parameters and has been returned to service with no issues identified.

Performed annual heating tune-up on 14-year-old Lennox furnace. Conducted thorough inspection including flame sensor cleaning and condensate drain system check. System is functioning properly with no humidity issues identified.

Performed scheduled tune-up service on Generac generator system. Inspected and verified proper installation of oil filter with "GENERAC" marking. All mechanical components, hoses, and electrical connections were examined and found to be in good working condition with no signs of leaks, corrosion, or damage.

Performed annual heating service on 23-year-old Nordyne furnace. Identified circuit board damage with evidence of overheating/burn marks around multiple resistors and diodes. Also noted significant deterioration of insulation on ducting with visible rust and corrosion. Documented issues with photos for reference.

Performed annual heating service on furnace system with integrated humidifier. Inspected and cleaned metal mesh filter components due to customer complaint of excessive static electricity in home. Verified humidifier operation and functionality, addressing customer concerns about its performance.