Expert HVAC, Plumbing & Generator Services in Mason

Responded to no cooling complaint at single family residence. Upon arrival, inspected HVAC system located in basement utility area including air handler, ductwork, refrigerant lines, and associated components. Documented equipment installation and current system configuration with photos for service records.

Responded to sump pump discharge issue where water was spraying back into the basement through a failed PVC pipe connection at the sump pit. Upon inspection, identified deteriorated connection fittings on the discharge line that had been leaking for approximately two months. Repaired the compromised PVC connection point at the sump basin, ensuring proper seal and secure fitting to prevent water from re-entering the basement area. Verified discharge line integrity from interior sump pit through exterior termination point at foundation, confirming proper drainage flow away from structure. Tested system operation under full pump cycle to confirm leak elimination and proper water evacuation. Documented existing installation configuration including discharge routing and exterior drainage connection. System restored to full operational status with no further water intrusion into basement area.

Provided estimate for water heater replacement in unfinished basement utility area. Assessed existing white tank-style water heater with current plumbing configuration including white PVC venting system, copper supply lines, and recirculation pump with electronic controls. Documented existing installation featuring ScaleBlaster water conditioning system, gray wall-mounted HVAC or water treatment unit, and black circulation pump at base of current heater. Photographed complete plumbing layout including complex PVC piping arrangements with multiple elbows and joints, aged copper piping with visible patina, and blue electronic controller for pump system. Reviewed accessibility within exposed wooden framing and evaluated requirements for new water heater installation to match existing connections and maintain proper venting through current PVC system.

Installed shut-off valve on dedicated gas line to stove in basement utility area and prepared connection point for new stove installation. Work completed on copper gas piping system with all connections tested and verified for proper operation and safety.

Responded to third service call for air conditioning system running continuously, requiring thermostat setting of 76°F to cycle off. Upon inspection, discovered significant disconnected ductwork in attic space, which was causing substantial conditioned air loss and preventing proper system cycling. Documented ductwork separation with photos showing metal duct connections pulled apart from mounting brackets and structural supports. Addressed customer concerns regarding previous capacitor diagnosis, confirming that disconnected ductwork was the primary issue affecting system performance rather than electrical components. Explained how air loss from separated ducts created continuous cooling demand, preventing thermostat satisfaction at normal temperature settings.

Responded to water leak emergency caused by screw penetration through copper water line in interior wall. Cut access opening in textured wall to expose damaged pipe section, verified leak location, and assessed extent of damage to surrounding wall materials. Repaired compromised copper plumbing line and restored water service to home.

Completed full air conditioning system replacement at residential property. Removed existing outdoor condenser unit and installed new gray cylindrical AC condenser with horizontal ventilation slats and protective top grille. Unit positioned on existing concrete pad in corner location against beige vinyl siding. Connected electrical disconnect box to new unit via gray conduit, verified proper electrical connections and grounding. Installed white PVC condensate drain line with proper pitch and termination. Confirmed unit placement on elevated concrete pad with adequate clearance for airflow and service access. Landscaping area around unit maintained with mulch bed and decorative stone border featuring stacked gray pavers. Verified all manufacturer specifications, tested system operation, and confirmed proper cooling performance upon startup.

Completed annual cooling system tune-up and preventative maintenance inspection. System evaluated and found operating within normal parameters; no immediate repairs required at this time.

Completed annual cooling maintenance on 11-year-old air conditioning system. Performed comprehensive tune-up including inspection of evaporator coil, which showed normal dust accumulation for unit age, and verified proper airflow through supply grilles. All components operating within manufacturer specifications. System tested and confirmed functioning properly. Documentation photos captured for service records.

Responded to customer complaint of loud banging noise from outside AC unit upon startup. Inspected exterior condensing unit and traced refrigerant lines into attic space. Found inadequately secured suction line creating vibration and impact noise against floor joists when compressor engaged. Repositioned and properly secured copper refrigerant line and associated flex duct using appropriate mounting straps and clamps to eliminate contact with structural framing members. Cycled system multiple times to verify noise elimination and proper operation.

Installed a Bradford White 40-gallon short natural draft water heater in residential utility room. Connected all water supply lines, gas piping, and exhaust venting with proper fittings and secured galvanized duct at top of unit. Verified all connections, tested system operation, and confirmed proper venting and drainage function upon completion.

Conducted on-site assessment for water heater replacement in residential property with existing unit at 18 years of age, nearing end of typical service life. Evaluated mechanical room configuration, photographed existing installation including HVAC ductwork and copper plumbing connections, and provided comprehensive estimate for new water heater installation in standard residential application.

Completed comprehensive super tune-up on 4-year-old Rheem air conditioning system. Performed full system inspection including electrical components, capacitor testing, contactor evaluation, and refrigerant line assessment. All components found operating within manufacturer specifications; capacitor showing proper microfarad readings, contactor functioning correctly with clean contacts, and refrigerant lines properly insulated with no visible leaks. Cleaned debris from capacitor mounting platform and verified all wire connections secure. System tested and confirmed cooling efficiently with no issues identified.

Responded to cooling deficiency complaint on 14-year-old air conditioning system in standard construction residence. Performed diagnostic inspection using borescope camera to examine evaporator coil condition and heat exchanger fins. Visual inspection revealed coil fin structure and internal component condition. Unit operational but underperforming on cooling capacity as reported.

Completed inspector-requested corrections for quoted repair work. Addressed floor opening in kitchen area where hardwood flooring meets stairwell access to basement level, ensuring proper framing and subflooring exposure meets code requirements. Verified and documented foam insulation sealing at basement ceiling/wall junction and confirmed electrical/mechanical component placement on concrete step surface meets inspection standards.

Successfully completed installation of two new water heaters in mechanical room. Installed one Lochinvar unit and one Bradford White unit side by side, connecting both to existing copper plumbing system with appropriate valves and fittings. Mounted circulation pump on Bradford White unit and completed all electrical connections with proper conduit. All manufacturer specifications followed, units tested and operational.

Responded to service call for leaking outdoor water spigot at residential property. Upon inspection, accessed plumbing system through ceiling cavity to locate source of leak at copper pipe connection serving exterior hose bib. Repaired faulty valve connection with oxidized copper piping, replaced worn components, and verified system integrity. Created access opening in wall/ceiling to reach affected plumbing, completed repairs, and confirmed no active leaks present upon completion.

Responded to no cooling call on 9-year-old Maytag system with thermostat displaying "lacking Y1 feed" fault. Upon arrival, found both heating and cooling functions inoperative following recent heat exchanger replacement performed by another contractor. Inspected Nest thermostat wiring at wall base and traced connections to furnace control board. Identified missing or improperly terminated Y1 wire connection at control board that was disturbed during previous heat exchanger service. Verified all thermostat wiring terminals including RC, W1, G, C, and Y1 connections. Re-established proper Y1 circuit connection at furnace control board terminal strip, ensuring secure termination. Tested system operation through multiple heating and cooling cycles. Confirmed thermostat fault cleared, air conditioning engaging properly on Y1 call, and furnace responding correctly to heat demand. System restored to full functionality with both heating and cooling operating as designed.

# NC-No Cool Service Completed Responded to no cooling complaint on 2-year-old EnergiAir system. Upon arrival, performed diagnostic testing using refrigerant manifold gauges and digital multimeter to assess system operation. Inspection revealed electrical control issues requiring attention to wiring connections at the condensing unit. Accessed electrical panel and examined CoreSense control board, contactor assembly, and dual-run capacitor (38/5 MFD). Verified proper wire terminations and electrical connections throughout the control circuit. Tested refrigerant pressures on both high and low sides of the system using professional-grade manifold gauge set with color-coded hoses. System restored to proper cooling operation following diagnostic work and necessary corrections to electrical connections.

Completed annual cooling maintenance on 6-year-old ICP system. Performed comprehensive tune-up including filter inspection, refrigerant level check, electrical connections verification, and condensate pump operation test. Confirmed condensate pump is properly elevated on wooden blocks and draining correctly through PVC discharge line; system operating within manufacturer specifications with no issues found.