Heating, AC, Plumbing & Generators in Portage MI

Inspected the tankless water heater after the reported error code and no-heat condition, and found heavy soot and carbon buildup in the cabinet interior. Verified the inlet plumbing, valve assembly, and PCB and wiring connections, and cleaned the unit to restore proper combustion and heat exchanger operation.

Responded to a water leak call on a 19-year-old Lennox system following a recent tune-up. Inspected the condensate drain pan and PVC drain fitting, found moisture accumulation around the drain connection and pan outlet, and corrected the leak at the fitting. Verified the condensate drain was draining properly and the pan was dry with no further leakage.

Installed a new 40-gallon tall natural gas water heater on a metal drain pan, with a connected flue vent and a yellow-wrapped gas supply line. Mounted a new expansion tank on the adjacent wall and completed copper water connections to the system.

Performed a furnace super tune-up on a 6-year-old unit, including inspection and cleaning of key components, verification of safe operation, and a system performance check. Also inspected the Aprilaire whole-home humidifier, ductwork, and insulation, and checked the adjacent Bradford White water heater, with no leaks, damage, or abnormalities observed.

Responded to a water softener leak caused by a component that detached from the bypass valve assembly while the customer attempted to isolate the unit. Inspected the softener, control head, and associated plumbing connections, confirmed the water supply was shut off, and addressed the failed bypass fitting to stop the leak. Documented the unit's condition and surrounding moisture with photos.

Responded to a gas water heater with no hot water and found the pilot had gone out. Inspected the gas control valve assembly and thermocouple wiring with a multimeter, checked associated wiring for damage, and performed a relight following manufacturer procedures. Verified proper pilot and burner operation and confirmed the unit was heating normally.

Installed a new Carrier gas furnace with a vented flue assembly, sheet-metal supply plenum, and condensate drain pan, along with an accessory air treatment component, and completed the associated gas, electrical, and drain connections. Installed a matching Carrier outdoor condensing unit on a level concrete pad with insulated refrigerant lines and a weatherproof electrical disconnect, completing the full furnace/AC system replacement.

Performed a furnace super tune-up, inspecting the cabinet interior, wiring harness, flame sensor/igniter, and control board connections and finding no wiring damage. Observed corrosion and rust staining on the cabinet wall near the inducer motor, indicating past moisture exposure, along with a heavily textured, corroded-looking run capacitor that should be tested and monitored for replacement. Cleaned accumulated dust and debris from the components and verified system operation.

Inspected a 30-year-old drop-in sink with a backed-up drain and found the sink's drain bottom to be rotted, which is the cause of the blockage. Examined the under-sink PVC drain assembly, including the P-trap, slip-nut couplings, and supply lines, and documented their condition with photos. Advised that the sink will require either drain repair or full sink replacement to restore proper drainage.

Installed a new 50-gallon natural gas Bradford White water heater (non-direct vent, 6-year warranty) on a drain pan, with copper water supply connections, gas control valve, and 3-inch vent flue connected to the existing galvanized vent duct. Installed a PVC drain line for the pan and T&P discharge. System was inspected for proper venting and leaks, and the unit is operational.

Performed annual heating inspection and tune-up on the furnace, including a review of the condensate drain system with attached humidifier. Observed the condensate pump and associated PVC drain lines and tubing to be dusty and grimy, and verified proper connections and routing. Confirmed the system is operating normally with the existing energy recovery/air quality equipment and active maintenance coverage.

Returned to the site to replace the controller on the Kohler standby generator. Removed the faulty controller, installed the new unit, and reconnected the wiring harness and conduit, verifying all connections were secure. Confirmed the generator powered up and operated properly with no fault indications.

Performed a Furnace Super Tune-up on a Bryant gas furnace, including inspection and cleaning of the blower assembly, where dust and soot-like grime buildup was found on the blower wheel blades, scroll housing, and motor area. Cleaned the affected components to restore proper airflow and verified safe, efficient operation of the system.

Replaced damaged copper drain lines by cutting access openings in the drywall ceiling and wall to expose the drain assembly. Removed the compromised sections and installed new PVC drain piping with an elbow fitting, transitioning to the existing cast iron line using stainless steel band couplings with rubber shielded connectors. Secured the new piping to the framing and left the access openings ready for drywall patching.

Completed the quoted repair on the HVAC condensate drain assembly, replacing and re-gluing the PVC drain line and elbow fittings to the condensate pump. Also inspected the adjacent water heater, noting corrosion and mineral buildup at the pipe connections on the top of the tank, which indicates a possible leak at the water heater fittings.

Performed annual furnace tune-up, inspecting the unit and verifying proper operation of the heating system. Inspected the condensate pump, drain tubing, and PVC condensate piping, finding connections intact with no signs of leaks, corrosion, or damage. No humidifier service was performed, per scope of work.

Completed a 200A electric service upgrade, including coordination of the utility disconnect and reconnect, electrical permit acquisition, and scheduling of the municipal electrical inspection. Installed new service entrance conduit, a meter socket, and an exterior disconnect enclosure with a new overhead service connection, then restored power following the utility reconnect.

Performed a complete furnace tune-up on a 25-year-old unit, including inspection of the cabinet, condensate pump and drain assembly, electrical wiring, and gas piping. Verified the condensate pump and PVC drain routing are secured and functioning, and noted surface corrosion on the black iron gas piping and fittings for monitoring. Completed the heat exchanger diagnosis documentation and obtained customer acknowledgement of the findings.

Responded to a reported water leak at an EnergiAir furnace and inspected the furnace and surrounding mechanical area, including the adjacent gas-fired water heater, its vent connector, and the supply piping and shutoff valve. Photo documentation of the mechanical space was taken, and no active leak source was documented at the time of inspection. Further diagnostics, such as checking the furnace condensate drain, trap, and secondary drain pan, are recommended if the leak recurs.

Diagnosed a leak at the washing machine drain, identified a cracked drain pipe allowing water to escape into the washer tub area following a recent shutoff valve replacement. Inspected the drain line and P-trap assembly beneath the utility basin, then repaired the cracked section and secured the connections to restore a watertight drain. Tested the system under load to confirm the leak was resolved.