Heating, AC & Plumbing Services in South Haven, MI

Performed annual heating inspection and tune-up on the furnace, verifying proper operation of the PVC venting/condensate drain assembly and pressure switch with the status LED indicating normal function. Inspected internal wiring and connections, finding no signs of frost, ice, rust, or cracking, and confirmed the system was operating normally at completion.

Capped and eliminated the abandoned gas line leading to the old meter, isolating it from the active gas supply and securing it with a threaded cap. Performed a leak test on the capped connection to confirm a gas-tight seal, with the remaining gas piping and meter assembly left in service.

Installed a new horizontal gas furnace in the crawl space on a drain pan, with sheet metal supply plenum connected to existing ductwork. Connected gas piping, electrical supply, and PVC condensate drain with condensate pump, and verified all warning labels and installation placards were in place. Unit appears clean and properly secured with no visible damage or leaks.

Accessed the wall cavity by removing the cabinet and opening the wallpapered wall section to expose the existing cast iron drain system. Replaced the deteriorated cast iron sections with new white PVC DWV piping, including a wye fitting and branch connection, and joined it to the remaining cast iron using shielded rubber transition couplings secured with stainless steel band clamps. Primed and solvent-welded all PVC joints, supported the vertical stack with pipe clamps, and verified the connections were secure and aligned.

Replaced two exterior hose spigots and installed a new exterior shower head on the patio-side wall, measuring and verifying the marked hot and cold supply line locations before work. Connected to the existing PEX supply lines in the basement mechanical area, then tested the new fixtures for proper operation and leaks.

Located the shovels requested for retrieval, staged against the exterior wall near the garage and refuse area. Confirmed their position and condition for pickup, and documented the site with photos. No additional service work was required.

Responded to a no-heat call on a 15-year-old Goodman furnace displaying a 3-flash fault code, indicating a pressure switch/inducer circuit issue. Inspected the system with a borescope and found corrosion and rust staining around an opening in the heat exchanger/vent passage, then diagnosed the cause of the lockout and advised on the necessary repair or replacement options.

Conducted an on-site estimate for a water conditioning system installation, including inspection of the crawl space to evaluate existing plumbing runs, pipe insulation, and overhead joist clearances. Documented the vapor barrier condition, spray foam insulation, and available access routes to determine proper equipment placement and supply line routing for the proposed system.

Inspected the reported sewer line leak and found active moisture at a corroded cast iron drain stack in the basement, with wetting and rust residue at the pipe couplings and pooling at the base of the stack. This is a recurring condition following prior partial drain repipe and P-trap work. The affected section of drain line remains a source of leakage, and replacement of that section is recommended to permanently resolve the issue.

Responded to no heat call on 8-year-old Trane furnace running but not reaching setpoint. Upon inspection, found burners showing signs of flame rollout and improper combustion patterns, evidenced by discoloration and oxidation on burner assemblies. Cleaned burner assembly, inspected heat exchanger for cracks or deterioration, verified proper gas pressure and flame sensor operation. Tested system operation through complete heating cycle, confirmed unit now heating properly and reaching thermostat setpoint with normal burner flame characteristics.

Completed full furnace installation at residential property. Installed new furnace unit with electrical control panel, wiring connections, and capacitor assembly. All electrical components properly terminated, system tested and verified operational upon completion.

Responded to a quoted repair for a boiler control board issue on a radiant heating system. Diagnosed and replaced the faulty control board in the wall-mounted boiler unit, restored proper system operation, and verified all heating zones and manifold circuits were functioning correctly. Completed work within the estimated timeframe and documented the installation with photos showing the boiler, expansion tank, and radiant floor heating manifold assembly.

Responded to electrical service call at two-story single-family residence to address under-sink heater fan and under-cabinet lighting issues. Performed initial assessment of confined crawlspace area beneath kitchen cabinetry, documenting existing plumbing infrastructure including copper and PVC piping systems within aged wooden framing. Photographed installation area showing network of copper water lines, HVAC components, and structural elements to establish baseline conditions for recommended heater fan removal or replacement and under-cabinet light fixture replacement work.

Successfully completed installation of a Bradford White 40-gallon natural gas water heater (Model RG24056N) in the mechanical room. Removed existing water heater and installed new unit with proper copper piping connections, brass fittings, and required safety valves. Connected gas supply line with appropriate pressure regulation per manufacturer specifications (40,000 BTU/hr input rating). Installed temperature and pressure relief valve, expansion tank connections, and verified all plumbing connections for leaks. Ensured proper venting and clearance requirements per installation guidelines. Tested unit operation, verified proper gas combustion, and confirmed water heating functionality. All work completed to code compliance and manufacturer specifications.

Responded to customer concern regarding natural gas odor near dryer connection following previous flex line replacement by handyman. Performed thorough inspection of gas supply line, connections, and newly installed dryer flex hose at wall penetration. Applied soap bubble test to all gas fittings and connections to verify system integrity. Confirmed all connections were properly sealed with no leaks detected. Advised customer that odor may be residual gas dissipating from previous minor leak and recommended monitoring. Documented installation with photos for customer records.

Responded to service call for mini-split systems installed in July that were not cooling properly. Accessed tight attic space to inspect units and check for refrigerant leaks using previously added UV dye. Examined outdoor condensing units and line sets on rooftop installation, inspecting drainage components and refrigerant lines for signs of leakage or system compromise.

Returned to property to perform combustion analysis on heating system and contacted technical support for consultation. Documented existing plumbing infrastructure showing advanced corrosion on copper piping and brass fittings in crawl space area, with horizontal pipe section displaying significant oxidation and surface deterioration requiring attention.

Performed comprehensive inspection of 27-year-old Reliant water heater and associated plumbing systems. Documented multiple safety and code compliance concerns including significant corrosion around water supply connections and heat source area, absence of required sediment trap on gas line, and improper shared exhaust venting configuration between water heater and boiler system. Photographed all deficiencies for client review and future remediation planning.

Conducted on-site evaluation for relocating existing gas line in basement area. Assessed current gas meter installation on exterior of building and inspected basement routing requirements through exposed joist space. Documented existing gas piping configuration, meter assembly with pressure regulator, and proposed pathway for line relocation. Provided estimate for gas line relocation work.

Completed furnace and air conditioning replacement estimate for property currently equipped with a 16-year-old geothermal Water Furnace system that is no longer operational. Client reported inadequate water flow to the geothermal system affecting cooling performance, though well pump has been verified as functioning properly and another contractor indicated refrigerant levels are adequate. Assessed existing vertical HVAC unit installation in unfinished basement with metallic ductwork and evaluated mechanical room containing water heater and water treatment equipment. Provided comprehensive estimate for converting from geothermal heating and cooling system to conventional furnace and air conditioning equipment.