Reliable HVAC, Plumbing & Generator Services in Sparta

Completed comprehensive AC tune-up on 7-year-old system. Removed heavy accumulation of leaves, pine needles, and organic debris from outdoor condenser unit and electrical components. Cleaned and inspected all electrical connections, including multi-circuit wiring harness and relay components. Verified proper operation of indoor Aprilaire humidifier unit and associated ductwork connections. All system components tested and confirmed operational within manufacturer specifications.

Completed annual cooling maintenance on EnergiAir system with 2022 condenser model under 3-year warranty coverage expiring June 2027. Inspected and documented condensate pump assembly including float switch operation, drain line connections, and proper discharge function. All components found operating within normal parameters with no deficiencies noted.

Installed new natural gas line to upstairs kitchen for stove conversion from electric to natural gas, including stub-up behind stove location. Additionally installed gas rough-in piping for future water heater conversion from electric to natural gas tankless system.

Completed annual cooling system tune-up on 28-year-old International Comfort Products unit with condenser model year 2022. Performed standard maintenance inspection, documented mechanical connections and plumbing components with photographic evidence, and verified all systems operating within normal parameters.

# Drain and Waste Repipe Completed Performed complete drain and waste system repipe in residential bathroom over two-day period. Excavated bathroom floor to access existing drain lines, removing flooring material to expose concrete substrate and underlying plumbing infrastructure. Demolished and removed deteriorated drain and waste piping system. Installed new PVC drain and waste piping throughout bathroom, including proper pitch and venting per code requirements. Routed new drain lines for toilet, bathtub, and lavatory fixtures. Connected all new waste lines to main building drain. Pressure tested all new piping to verify system integrity and proper drainage function. Coordinated fixture rough-in locations to match existing bathroom layout. All work performed in accordance with applicable plumbing codes and industry standards. System ready for floor restoration and fixture installation.

Conducted water heater replacement estimate for existing AO Smith unit located in basement utility area. Assessed current installation including copper supply lines with foam insulation sleeves, vertical venting system, and connections to existing plumbing infrastructure. Documented mechanical space configuration with exposed framing and provided recommendations for replacement equipment and installation requirements.

Completed annual cooling system maintenance and tune-up on 2011 AC unit. Performed comprehensive inspection of all components, removed and cleaned blower motor assembly, verified proper operation of all mechanical systems, and confirmed unit is operating within manufacturer specifications for the upcoming cooling season.

Responded to inspection correction notice regarding improperly configured furnace venting system. The air intake and exhaust terminations were found to be reversed and positioned too close to the fresh air intake, creating a potential safety hazard and code violation. Corrected the PVC vent pipe configuration by properly routing and repositioning the intake and exhaust terminations to meet manufacturer specifications and local building code requirements for proper clearance distances. Verified adequate separation between combustion air exhaust and fresh air intake to prevent recirculation of flue gases into the system.

Completed annual cooling system maintenance and inspection. Performed comprehensive tune-up including checking refrigerant levels, cleaning condenser coils, inspecting electrical connections, and testing system operation. Verified condensate drain pan and drainage system are functioning properly with no blockages or leaks present.

Responded to service call for boiler not reaching set temperature on 10-year-old system. Upon inspection, identified control unit malfunction preventing proper temperature regulation. Examined wall-mounted heating control with digital display and associated valve manifold system including multiple brass fittings with colored handles. Assessed copper piping connections and electrical junction boxes showing signs of age and patina buildup. Verified proper electrical connections at terminal points and evaluated overall system operation to restore heating functionality to programmed temperature settings.

Completed annual cooling system tune-up and preventative maintenance inspection. Inspected condensate pump assembly, verified proper operation and drainage function, and documented equipment condition with photos. System is operating within normal parameters under existing warranty coverage through August 2033.

Responded to service call for 9-year-old Goodman furnace that sustained water damage from basement sump pump failure. Performed thorough inspection of unit and electrical components, documented condition with photos, and tested blower fan assembly to rule out motor failure. Determined that water intrusion may have compromised electrical control panel and recommended potential panel replacement to restore safe operation.

Completed full air conditioning system replacement at residential property. Installed new outdoor condenser unit on existing concrete pad with proper electrical disconnect, conduit routing, and refrigerant line connections to house. Verified all connections, tested system operation, and ensured unit was level and properly secured with adequate clearance for airflow and future maintenance access.

Performed comprehensive load calculation estimate for operational air conditioning system currently experiencing refrigerant leak. Completed detailed HVAC load analysis spreadsheet documenting supply run measurements across multiple zones (North, South, East, West orientations for Main, Upper, and Lower runs), calculated heating load requirements totaling 56,825 BTU based on 70°F indoor to 8°F outdoor design conditions, and determined cooling load of 21,413.60 BTU for 70°F to 75°F indoor conditions with 90°F outdoor ambient temperature. Assessment included evaluation of ceiling insulation values, wall heat transfer for multiple floor levels, infiltration rates, glass surface areas, door losses, and occupancy heat gain to provide accurate system sizing recommendations for replacement or repair options.

Replaced kitchen garbage disposal unit with customer-supplied model. Disconnected existing disposal from sink drain and electrical connection, removed old unit, and installed new disposal unit ensuring proper mounting to sink flange. Reconnected drain plumbing and electrical power cord, tested unit for proper operation and verified no leaks in the system.

Completed kitchen faucet installation on double basin composite sink with butcher-block countertop. Installed brushed stainless steel faucet with high-arc spout and matching side spray assembly, ensuring proper connections to existing supply lines and adequate clearance for sink operation. Verified all plumbing connections beneath sink were secure, tested water flow and spray functions, and confirmed no leaks at supply lines or drain connections.

Completed annual cooling maintenance on 13-year-old EnergiAir system with contract maintenance through 2026. Performed standard tune-up procedures including system inspection, performance verification, and documentation with photographs of equipment location on exterior siding.

Completed annual heating maintenance on 9-year-old furnace and humidifier system. During inspection, discovered significant frost and ice crystal accumulation on air handler components and metal surfaces, indicating abnormal temperature regulation or airflow restriction. The frost buildup was concentrated around component seams, metal plates, and a circular port opening, with white crystalline deposits extending along equipment edges. Documented conditions with photographs showing the extent of ice formation on gray metal components and adjacent ductwork. The frost accumulation pattern suggests potential issues with condensate drainage, refrigerant flow, or humidity control that will require further diagnosis and correction to prevent system damage and ensure proper heating season operation.

Responded to call regarding water heater not maintaining adequate hot water supply with suspected thermostat failure on 7-year-old unit. Upon arrival, performed diagnostic inspection of water heater system including visual examination of unit condition, electrical connections, and control components. Inspected electrical panel supplying power to water heater and verified proper circuit operation. Examined water heater insulation, piping connections, heating elements, and thermostat controls. Documented equipment condition and installation configuration with photographs for service records. Evaluated overall system performance and identified potential causes for inadequate hot water production.

Responded to drainage issue affecting single drain related to water softener backflow in twelve-year-old residence. Upon inspection, identified improper drainage configuration in utility area where water softener discharge line was creating backflow conditions. Cleared obstruction from affected drain line, verified proper flow through PVC drainage system, and confirmed all connections were secure and functioning correctly. Documented plumbing configuration including water supply lines, drainage piping, and water softener installation with photographic evidence for service records.