Heating, Cooling, Plumbing, and Electrical Services in Ada

Inspected the existing natural gas tank water heater following a reported overflow and assessed the installation for replacement, including the draft hood and galvanized flue vent, copper water connections with ball valve, and surrounding electrical and ductwork. Documented unit condition, including moisture and rust-colored residue at the flue and pipe connections, and prepared an estimate for supply and installation of a new natural gas tank water heater.

Conducted an on-site furnace replacement estimate for a 14-year-old Bryant gas furnace with an existing whole-home humidifier installed in a basement utility area. Inspected the furnace cabinet, supply plenum and trunk ductwork, refrigerant line set, PVC condensate drain, gas supply line, and surrounding clearances, documenting equipment data plates and existing system configuration with photos. No visible rust, frost, or ductwork damage was observed, and the existing duct seams were found sealed with foil tape and mastic.

Performed annual heating tune-ups on three furnaces (Ruud, ENE, and a Sears wall furnace) and the associated humidifier, inspecting and servicing components for safe, efficient operation. Visually inspected the power-vent water heater, vent piping, and adjacent copper supply lines and shutoff valves, and found no evidence of leaks, corrosion, or damage.

Responded to a 12-year-old Lochinvar Knight wall-mount boiler reported as locked out with no heat. Referenced the manufacturer's troubleshooting table for the "Flame Fail Ign" fault (failure to prove main burner ignition after four attempts) and performed the corrective diagnostics, including inspection of the wiring harness, spark electrode, grounding, gas supply pressure, gas valve voltage, flame sensor, and burner. Reset the control and verified the unit returned to normal standby operation.

Cleared blockages in two toilets and one bathtub drain that were backing up and failing to flush or drain. Augered the fixtures and associated drain lines to remove the obstructions, then tested each toilet flush and the tub drain to confirm proper flow and no leaks. All three fixtures are now operating normally.

Evaluated a hot water delivery complaint at the master bath, the fixture farthest from the water heater, where hot water is available only briefly. Inspected the mechanical room piping and found a pressed-copper distribution manifold with a multi-port valve assembly and isolation ball valves, and removed a chrome T-fitting that showed heavy mineral and corrosion buildup around its valve cartridge and worn threads, which likely restricts flow. Recommended replacing the corroded fitting and cartridge, and evaluating a hot water recirculation system or rerouting of the supply line to improve hot water delivery to the master bath.

Installed a new Amana upright gas furnace on a drain pan, with PVC intake/exhaust venting and condensate piping routed and connected, gas supply line hooked up, and supply plenum tied into the existing ductwork. Verified all connections and labeling were in place, and confirmed the unit was properly set and ready for operation.

Performed annual preventive maintenance and tune-up on a Generac 22kW standby generator. Inspected the engine compartment, hoses, clamps, oil drain assembly, and enclosure interior, finding all components clean and intact with no signs of rust, leaks, frost, or damage. Unit was left in good working condition with no issues identified.

Responded to a newly installed Bradford White electric water heater with a failed heating element. Drained the tank using a hose, removed the defective element with a hex wrench, and installed a new replacement element. Refilled the tank, purged air from the lines, and verified proper heating operation.

Performed annual heating maintenance on a gas furnace, including removal of lower access panels, inspection of the control board, wiring, inducer/blower assembly, and PVC vent and condensate piping, along with testing of system operation using a digital gauge. Inspected the Aprilaire humidifier on the supply plenum and noted discoloration and residue along a bolted panel seam in the heat exchanger section, which warrants monitoring for corrosion or leakage. No frost, rust, or ice buildup was observed on surrounding components.

Responded to a no-cooling complaint on a system that had been running for hours without lowering indoor temperature. Measured a 49.2°F supply air reading at the air handler, indicating the refrigeration circuit was producing some cooling, and inspected the cabinet interior. Found the evaporator coil dirty and oxidized, a torn and delaminated duct board liner exposing fiberglass insulation, and heavy dust and debris buildup on the adjacent filter surface, all of which can restrict airflow and degrade heat transfer and system capacity. Documented these conditions with photos and identified them as contributing factors to the reduced cooling performance.

Performed annual heating tune-up on an 8-year-old furnace with humidifier, inspecting electrical connections, wiring, and internal components. Identified a heavily corroded red spade connector on a terminal block, likely from humidifier-related moisture exposure, and recommended replacement of the connector to ensure reliable electrical continuity.

Installed a new geothermal heat pump system in the basement mechanical area, including a vertical air handler on a vibration-isolation pad with insulated supply plenum and ductwork connections. Completed the PVC loop piping with isolation valves, pressure gauges, and fittings, and mounted and wired the associated electrical disconnects and controls. System was left clean, properly secured, and free of visible leaks or damage.

Responded to a reported gas leak after the utility had shut off service and a prior pressure test failed to locate the source. Opened the drywall ceiling to inspect the concealed gas piping and found a corrugated stainless steel tubing (CSST) run terminating abruptly with an exposed, uncapped end at the floor framing, indicating a compromised line and the likely leak source. Documented the condition of the CSST, adjacent corroded black iron piping, and brass fittings with photos. The unsafe section should be isolated and repaired or replaced, followed by a pressure test before gas service is restored.

Installed a new 50-gallon tall electric Bradford White water heater in a drain pan, with copper supply connections, a drain valve, and a temperature and pressure relief discharge line routed to the floor drain. Verified connections are secure with no visible leaks, and the unit is properly positioned and ready for operation.

Inspected the kitchen sink drain and supply plumbing to locate the source of the reported leak. Found rust-colored staining and residue at the PVC slip-nut couplings and drain joints beneath the sink, indicating slow seepage at the threaded connections. The copper supply lines, shutoff valve, braided supply connectors, and disposal connections were also checked for moisture and showed no active leakage.

Performed annual heating tune-ups on two Carrier furnaces and serviced the humidifier, including inspecting and cleaning the condensate drain pan and replacing the pan treatment tablets. Verified proper furnace operation and cleared debris from the work area to ensure unobstructed drainage and airflow.

Completed scheduled 5-year maintenance tune-up on Generac generator unit. Performed comprehensive inspection of all mechanical components including valve assembly, motor housing, piping connections, and exhaust system. Verified oil drain valve operation and documented equipment condition with service labels updated. All components found to be in normal operating condition with appropriate wear patterns for equipment age. Generator tested and confirmed operational within manufacturer specifications.

Completed full furnace installation in basement utility area. Installed new gray metal multi-compartment furnace unit with proper PVC venting system routed vertically for exhaust and intake. Connected all necessary ductwork including flexible ducting, verified all electrical connections, and ensured proper clearances per manufacturer specifications. System tested and operational upon completion.

Responded to gas leak call at residential property where customer had shut off gas supply as a safety precaution. Located and identified gas leak originating from piping outside the furnace room in basement area. Inspected exposed gas lines running through unfinished basement space with visible framing and mechanical systems. Assessed leak point on gas piping, performed necessary repairs to eliminate leak, and pressure tested system to verify integrity of repair. Restored gas service and confirmed all connections were secure with no detectable leaks present upon completion.