Top-Rated HVAC & Plumbing Services in Grand Haven, MI

Responded to no cooling call and performed diagnostic inspection of HVAC control board assembly. Upon examination, documented the electronic control board configuration including integrated circuits, capacitors, relay switches, and wire terminations within the white plastic enclosure. Board appeared to be properly mounted and secured with visible terminal connections intact. Captured detailed photographs of the control board assembly for service records and further analysis of the system's electronic components and wiring configuration.

Relocated Generac standby generator unit to new position along side of residence per client request. Generator was disconnected, moved from original location, and reinstalled on prepared gravel pad with proper clearances from structure and adjacent HVAC equipment. Unit was reconnected, tested for proper operation, and site was left clean and organized with landscaping materials staged for completion of surrounding area.

Completed comprehensive two-year tune-up service on Generac generator unit. Performed standard maintenance procedures including inspection of all mechanical components, hoses, connections, and filters; verified proper operation of fuel system and all associated fittings; and documented equipment condition through photographic records to ensure system reliability and continued optimal performance.

Completed annual cooling maintenance on 2023 Bryant AC system. Performed comprehensive tune-up including system inspection, verified REME HALO UV air purifier operational status and proper mounting on ductwork, and measured capacitor reading at 96.6 MFD to confirm electrical component performance within specifications.

Completed installation of a 40-gallon Bradford White natural gas water heater in residential utility room. Unit was properly positioned, connected to existing copper water supply lines with brass fittings and compression valves, and vented with metallic ductwork including elbow joint for proper exhaust routing. All plumbing connections, gas line hookups, temperature and pressure relief valve, and safety controls were installed per manufacturer specifications and local code requirements.

Responded to service call for humidifier hookup and AC unit evaluation. Upon arrival, assessed 6-year-old Goodman air conditioning condenser unit currently positioned on black plastic pad in residential yard. Confirmed unit is sitting at an improper angle, which can affect drainage and long-term performance. Discussed relocation options with customer to address leveling concerns and improve overall system positioning. Documented current installation conditions through photographs showing unit placement on uneven ground with displaced concrete support blocks nearby. Provided recommendations for proper leveling and potential repositioning of outdoor condenser unit to ensure optimal operation and longevity.

Responded to service call for 13-year-old tank-style water heater producing unusual noises while still providing hot water. Performed comprehensive inspection of unit, examining all plumbing connections, pressure relief valve, and heating elements. Assessed condition of copper supply lines, shut-off valves, and venting system. Evaluated sediment buildup as likely cause of noise based on unit age and operational symptoms. Documented current state of water heater with photographs showing all connections, labels, and surrounding utility space. Confirmed unit is functioning and producing hot water but recommended monitoring given age of equipment approaching typical service life expectancy. Provided assessment findings to customer regarding replacement considerations.

Completed full air conditioning system installation including outdoor condensing unit and indoor evaporator coil integration with existing furnace. Installed and connected copper refrigerant lines with proper insulation, established electrical connections, and integrated new AC components with current heating system. Charged system with refrigerant, verified proper operation of all components, and confirmed airflow through existing ductwork. Tested system performance with temperature differential readings showing 107°F and 104°F at service ports, indicating proper refrigerant charge and system operation. Installed required venting modifications using PVC piping for condensate drainage and secured all connections per manufacturer specifications. System operational and performing within normal parameters upon completion.

Completed full air conditioning system replacement at residential property. Installed new outdoor condensing unit on existing concrete pad against exterior foundation, ensuring proper placement and secure mounting. System was commissioned, tested for proper operation, and left in full working order with all refrigerant lines connected and electrical connections verified.

Completed annual cooling maintenance on 17-year-old air conditioning system. Performed comprehensive tune-up inspection of all major components, verified proper refrigerant levels, checked electrical connections, and confirmed system operational efficiency. Updated customer contact information and documented equipment condition with photos of condensate drain assembly and internal mechanical compartment showing all connections secure and functioning properly.

Completed full HVAC system installation including outdoor Amana condensing unit positioned in side yard on concrete paver pad with proper clearances and indoor furnace with air handler in basement mechanical room. Ran refrigerant line set from exterior unit through wall penetration with secure mounting brackets and proper insulation. Installed white PVC condensate drain piping and venting system connected to furnace, routed along basement ceiling to code-compliant termination points. Positioned equipment on protective pads over concrete surfaces. Connected all electrical components, verified proper voltage and amperage to both indoor and outdoor units. Pressure tested refrigerant lines for leaks, evacuated system, and charged to manufacturer specifications. Verified airflow, temperature split, and proper cycling of both heating and cooling modes. All installations meet current building codes and manufacturer requirements for warranty compliance.

Completed spigot replacement on corroded vertical supply line. Removed existing deteriorated pipe assembly showing significant rust and corrosion at joint connections, installed new spigot fixture with proper sealing to restore water flow and prevent leaks.

Completed annual cooling maintenance on 7-year-old Comfortmaker air conditioning system. Performed comprehensive tune-up including system inspection, tested all electrical components and controls, cleaned condensate drain pan which showed moderate debris accumulation, verified proper operation of safety switches, and documented equipment condition with photos. Unit operating within normal parameters upon completion.

Completed full air conditioning system replacement at residential property. Installed new outdoor condensing unit on existing concrete pad adjacent to building exterior, ensuring proper leveling and secure mounting. Connected refrigerant lines, electrical service, and PVC condensate drain line with upward routing along building siding, verifying all connections met manufacturer specifications and local code requirements.

Completed full residential HVAC system installation including new Amana furnace and outdoor AC condenser unit. Furnace installed in interior mechanical room with proper venting using white PVC piping, connected to existing ductwork infrastructure, and integrated with water heater utilities. Outdoor condenser unit positioned on concrete pad against exterior wall with appropriate clearances, electrical disconnect box mounted, refrigerant lines and conduit properly routed through siding. All equipment secured, tested for proper operation, and system commissioned to manufacturer specifications.

Completed full air conditioning system replacement including outdoor condenser unit and associated components. Installed new outdoor condensing unit on existing concrete pad with proper leveling and secured all refrigerant line sets using copper tubing routed along exterior wall and through crawl space access. Mounted and secured black flexible refrigerant line insulation and copper piping to building structure using appropriate mounting hardware and strapping. Connected electrical disconnect box to new unit and verified all electrical connections meet code requirements. Tested system operation, confirmed proper refrigerant charge, and verified all connections are secure and leak-free.

Conducted on-site evaluation for standby generator installation at residential property. Assessed existing utility infrastructure including natural gas meter assembly with pressure regulator and electrical service panel to determine feasibility and requirements for generator system. Client expressed interest in Kohler generator models. Documented current gas and electrical service locations with photographs, noting landscaping considerations around utility equipment areas. Provided pricing estimate conditioned on final specifications and equipment selection.

Completed full furnace installation in residential basement utility room. Installed Carrier brand furnace unit with complete ductwork system, including vertical and horizontal duct connections to existing infrastructure. Connected all necessary PVC venting pipes, gas lines, electrical components, and control systems to ensure proper operation. System tested and verified operational upon completion.

Responded to miscellaneous plumbing repair request and inspected circulation pump system connected to copper piping and expansion tank in basement utility area. Diagnosed pump failure requiring replacement, but necessary parts were not available on truck. Left job site with customer aware of work (CWOW), and scheduled return visit within 2 hours to complete pump replacement once parts are retrieved from shop.

Completed annual cooling maintenance on 2018 residential HVAC system with 10-year equipment warranty. Performed comprehensive tune-up including inspection of electrical connections, control components, and CoreSense monitoring system. All wiring connections verified secure, voltage levels tested within normal operating parameters, and system confirmed operational for cooling season.