HVAC & Plumbing Services in Grand Rapids, MI

Performed annual heating tune-up on gas furnace, inspecting the burner assembly, gas valve, limit switches, pressure switch, and wiring connections, with all components found clean and free of rust, frost, or damage. Unit is operating properly, and no humidifier service was required.

Replaced the corroded washer and dryer shut-off valves within the recessed supply box, installing new valves with green handles and reconnecting the braided stainless steel supply hoses. Verified the connections were secure and the drain hose was properly positioned, restoring reliable water shut-off control to the laundry appliances.

Performed Furnace Super Tune-ups on three gas furnaces (two Goodman units, approximately 19 and 16 years old, and one 18-year-old Weather King unit), including inspection of the blower compartments, electrical connections, and cabinet interiors. Found heavily dust-laden return air grille and filter media restricting airflow, and significant rust and corrosion along the cabinet floor seam beneath the blower housing, indicating possible moisture intrusion that should be monitored or repaired to prevent further deterioration. Recommend replacing filters and cleaning the return grille regularly, and having the corroded cabinet area evaluated at the next service visit.

Removed the existing toilet and installed a new two-piece toilet, including a new wax ring seal and closet bolts, and secured it level and flush to the finished tile floor. Connected the braided stainless steel supply line to the chrome angle stop valve, then tested for proper flush operation and verified no leaks at the supply connection or base.

Performed annual heating inspection on a 13-year-old furnace, including visual assessment of the air handler, return filter grille, burner box, heat exchanger inlets, gas valve assembly, and control wiring. The return air filter was found dusty and discolored, indicating restricted airflow and the need for replacement. A scorched, deteriorated wire with degraded insulation was identified near the burner/manifold area, a safety concern requiring repair or replacement of the affected wiring to prevent shorting or ignition-system failure. Recommend correcting the damaged wiring and replacing the filter to restore safe, efficient operation.

Responded to a non-responsive LUX TX 500 E thermostat that was failing to call for heat despite battery replacement and reset attempts. Diagnosed the control and verified the system's operation. A borescope inspection of the venting/ductwork also revealed a cracked, deteriorated ring-shaped fitting at the opening, which was documented with photos and video for further evaluation. Replaced the thermostat as needed to restore furnace operation.

Performed annual tune-up on 12-year-old Goodman furnace (no humidifier installed), including inspection of the blower compartment and cleaning of accumulated dust and debris from the blower motor housing and surrounding components. Verified furnace operation and safety controls for proper function, and system is operating normally at completion.

Performed a complete Furnace Super Tune-up, including inspection and cleaning of the furnace's major components, with the interior of the unit's blower/burner compartment accessed and serviced. Verified safe, efficient operation and proper function of the system following service.

Replaced the existing single-lever shower valve and trim, accessing the valve from the adjacent closet space by cutting an opening in the wall and finishing it with an access panel. Installed 1/2" shut-off valves on the hot and cold supply lines to allow future service with minimal water interruption. Restored water service and verified proper operation and leak-free connections.

Responded to a leaking Bradford power vent water heater and inspected the unit, including the blower assembly, PVC venting, and copper supply piping with shutoff valve. Evaluated the source of the leak and confirmed the unit's condition and installation components for further service recommendations.

Installed a new furnace in the basement mechanical space, connecting it to the existing galvanized supply ductwork with a rounded elbow transition and sealing the plenum and duct joints with foil-faced tape. Ran flexible metal conduit to the electrical junction box for power, and tied the PVC condensate drain line and condensate pump into the existing drain. Verified connections and secured the unit in place, with manufacturer and warranty tags left on the cabinet.

Removed the existing two-handle bathroom faucet, reviewed replacement options with the customer, and installed the selected new faucet during the same visit. Verified secure connections and proper operation of both handles and the pop-up drain assembly, with no leaks observed at the supply lines or drain.

Performed annual heating tune-up on the furnace, inspecting the blower motor, wiring harness, and control board connections, with no signs of damage, corrosion, or loose connections observed. Inspected supply ductwork and plenum connections, noting worn and lifting foil tape at the round duct transition and moisture present near the plastic flange, which should be monitored and resealed as needed. System operation verified and no humidifier was serviced per scope of work.

Performed annual heating tune-up on the furnace and humidifier, including a borescope inspection of the heat exchanger and internal components. Inspection revealed minor surface rust and corrosion staining at isolated seams and fittings, with no visible cracks or breaches confirmed, and findings were documented with photos and video for monitoring at future visits.

Installed a whole-home sediment filter on the main water supply line in the basement mechanical area, mounting the filter housing to the wall and tying it into the existing copper piping with a shutoff valve for isolation during future cartridge replacement. Verified secure connections, restored water flow, and confirmed the system holds pressure with no leaks.

Performed annual heating tune-up on 11-year-old furnace equipped with whole-house humidifier. Serviced the humidifier system, including disassembly and inspection of the humidifier tray and components, and cleaned and reassembled the unit for proper operation. Verified furnace and humidifier functioned correctly following service.

Responded to a follow-up call for a slow-draining kitchen sink following a prior service visit. Inspected the under-sink drain system, including the garbage disposal, P-trap assembly, and dishwasher drain line, and found the drain line showing buildup and residue. Cleared the restriction in the kitchen sink drain and restored proper flow.

Performed annual heating tune-up on the furnace and whole-home humidifier, including inspection of the burner assembly, heat exchanger, flame sensor, ignition components, and gas connections, with cleaning and adjustment as needed to ensure safe, efficient operation. Verified proper venting, combustion performance, and humidifier function, and confirmed the system operating normally at completion with no deficiencies noted.

Corrected the gas piping installation to comply with the inspector's cited violation under MRC Section G2415.9, which requires the piping to be located a minimum of 3½" above grade. Adjusted the exterior gas line routing at the condensing unit and verified clearance with a tape measure, confirming the pipe now sits at the required height above the concrete surface and is ready for reinspection.

Responded to a report of toilet drainage backing up into the tub and inspected the fixture, finding an obstruction lodged at the bowl's drain opening. Cleared the blockage from the toilet drain and verified proper flow, with the bowl holding clear water and the drain line draining freely without backing up into the tub.