HVAC, Plumbing & Generator Services in Plainwell, MI

Completed annual cooling maintenance on Lennox AC system with approximately 5 years of service. Performed comprehensive tune-up including system inspection, component testing, and preventive maintenance procedures to ensure optimal cooling performance for the upcoming season.

Responded to inspection correction notice requiring protective coating on exposed gas piping outside building envelope. Applied corrosion-resistant paint to all exposed black iron pipe sections on exterior installations, including gas meter connections and standby generator supply lines, to comply with MRC G2414.8, IFGC 403.8, MRC G2415.11, IFGC 404.11, MRC G2415.11.2, and IFGC 404.11.2 requirements for pipes in corroding conditions.

Completed annual cooling maintenance on 2021 Goodman air conditioning system. Performed comprehensive tune-up including inspection of outdoor condenser unit, refrigerant lines, and electrical connections. All components found operating within normal parameters with no issues identified during this preventative maintenance visit.

Responded to no-cooling call for 25-year-old residential outdoor HVAC unit that failed to operate. Upon arrival, found condenser unit completely inoperative with extensive rust and corrosion throughout the fan guard assembly and top plate. Inspected heavily weathered condenser fan motor assembly, protective cage, and mounting components showing significant oxidation from prolonged environmental exposure. Unit's advanced age and deteriorated condition indicated end of serviceable life, requiring full system replacement to restore cooling functionality.

Completed comprehensive ASTU-AC Super Tune-up on a 20-year-old American Standard air conditioning system. Performed full system inspection, cleaned condenser coils, checked refrigerant levels and pressures, tested electrical connections, verified proper airflow, inspected condensate pump operation, and confirmed all safety controls functioning properly. System operating within manufacturer specifications with no immediate repairs needed.

Completed annual cooling maintenance on a 2018 Comfortmaker air conditioning system. Performed comprehensive AC tune-up including inspection of outdoor condensing unit, refrigerant lines, and indoor components. Unit placement confirmed acceptable per AMS standards. Customer was notified of and acknowledged later arrival time for service appointment.

Completed annual cooling maintenance on 26-year-old Goodman air conditioning system with condenser model year 2020. Performed comprehensive tune-up including inspection of outdoor unit, verified proper operation of all components, checked refrigerant levels, cleaned condenser coils, and confirmed electrical connections at disconnect box. Unit operating within normal parameters with no immediate service needs identified.

Responded to no hot water call where pilot light was out on Rheem water heater. Previous plumber had incorrectly diagnosed issue as ventilation problem and advised keeping door open, which did not resolve the condition. Performed diagnostic evaluation of water heater pilot assembly, thermocouple, and gas valve operation. Identified actual failure point preventing pilot from staying lit. Completed necessary repairs to restore hot water function and verified proper pilot ignition and burner operation upon completion.

Completed electrical outlet and surge protection work involving junction box wiring in ceiling. Properly terminated and secured multiple circuit conductors using approved wire connectors, ensuring all connections met code requirements for safe operation.

Completed full air conditioning system replacement at residential property. Removed existing outdoor condensing unit and installed new high-efficiency AC condenser on concrete pad with proper refrigerant line connections and electrical disconnect. Installed new evaporator coil at furnace location in basement, integrated with existing gas furnace system. Ran refrigerant linesets through exterior wall with appropriate insulation and PVC line hide. Connected condensate drainage lines with proper pitch and termination. Installed new thermostat wiring and verified all electrical connections meet code requirements. Pressure tested refrigerant lines for leaks, evacuated system to proper vacuum levels, and charged unit to manufacturer specifications. Verified proper airflow across evaporator coil and through ductwork. Started system and confirmed cooling operation, checked temperature split across coil, and monitored system pressures during operation. Reviewed thermostat operation and system c

Completed annual cooling maintenance on Carrier system with warranty through May 2027. Performed comprehensive tune-up including inspection of refrigerant lines, electrical connections, and mechanical components in confined equipment area. System operating within normal parameters with no deficiencies noted at time of service.

Completed annual cooling system tune-up and preventative maintenance on residential AC unit. Performed comprehensive system inspection, cleaned condensate drain line using wet/dry vacuum, checked refrigerant levels, tested electrical connections, and verified proper airflow through evaporator coil. All components operating within manufacturer specifications; system ready for cooling season.

# NC-No Cool Service Responded to service call for AC unit tripping breaker at furnace when turned on. Upon inspection, found heavily soiled blower assembly with significant dust and debris accumulation on blower motor and housing. Discovered compromised wiring with frayed and stripped conductors at terminal connections, creating potential short circuit condition. Identified exterior line set with corrugated conduit running through foundation area showing signs of environmental exposure. The breaker tripping was attributed to electrical fault caused by deteriorated wiring and excessive dirt buildup on motor components creating increased amp draw and potential ground fault.

Completed full HVAC system replacement including outdoor condensing unit and indoor air handler/furnace. Installed new dark gray condenser on existing rock pad against exterior wall with proper clearances maintained. Mounted electrical disconnect box and ran refrigerant line sets with appropriate insulation. Interior installation included new furnace unit with integrated ductwork connections, PVC venting system with proper slope and termination, and Aprilaire humidifier mounted to supply plenum. Verified all electrical connections, tested system operation across all modes, confirmed proper refrigerant charge and airflow, and ensured humidity control integration. System commissioned and left in full operational status.

Completed annual cooling maintenance on EnergiAir system under 5-year warranty agreement. Performed comprehensive tune-up including inspection of refrigerant levels, electrical connections, condensate drain system, and all major components. System operating within manufacturer specifications with no issues found; documented equipment condition with photos of utility area and drainage piping.

# NOISE - Noise Problem Resolution Responded to service call for excessive noise from air conditioning system following routine tune-up. Upon inspection, discovered significant accumulation of leaves and debris in outdoor condensing unit. Cleaned condenser coil fins and removed all foreign material from unit interior and surrounding area. Verified proper airflow through heat exchanger and confirmed all electrical connections secure. Tested system operation and confirmed noise issue resolved with normal operating sound levels restored.

Conducted on-site evaluation for standby generator installation. Customer expressed interest in Generac system and requested competitive pricing estimate. Inspected existing electrical service panel, documented current Cutler-Hammer load center configuration with main breaker and circuit distribution layout. Assessed installation requirements including panel capacity, transfer switch integration points, and optimal generator placement considerations to provide comprehensive proposal for automatic backup power system.

Responded to no-cooling complaint on 9-year-old residential air conditioning system. Upon arrival, confirmed indoor blower motor operational but outdoor condensing unit not running with 7-degree temperature differential between setpoint and actual room temperature. Performed diagnostic evaluation of outdoor unit, inspected electrical connections at disconnect box, and examined refrigerant line set and associated components. Verified proper power supply to condensing unit and tested capacitor, contactor, and compressor functionality. Identified failed component preventing outdoor unit operation and completed necessary repairs to restore system to proper cooling operation. Cycled system through complete cooling cycle to verify proper operation of both indoor air handler and outdoor condensing unit. System restored to normal operating condition with adequate airflow and proper refrigerant circuit operation.

Completed comprehensive plumbing project involving installation of new iron curtain water treatment system with associated PVC and copper supply lines routed through wall cavity. Performed rough-in plumbing for laundry tray installation in utility room, including proper drainage and supply connections within cabinet area. Removed existing Gordon brand iron curtain system and replaced malfunctioning pressure vacuum breaker on irrigation sprinkler system to restore proper backflow prevention. All installations completed to code with appropriate pipe labeling and secure mounting within framing structure.

Conducted site assessment for standby generator installation at residential property. Existing Generac transfer switch and electrical wiring already in place and operational. Documented current electrical service configuration including Centron digital utility meter rated at CL200, 240V, 3-wire with 30TA capacity. Verified transfer switch mounting location on exterior wall with adequate clearance and accessibility. Photographed existing infrastructure to prepare Kohler generator equipment proposal. Installation will require generator pad placement, gas line connection, and integration with pre-existing transfer switch system.