Reputable HVAC, Plumbing & Generator Services in Zeeland, MI

Performed annual heating tune-up on a 7-year-old Rheem gas furnace with whole-home humidifier. Removed and inspected the burner assembly and flame sensor, which showed oxidation, soot, and mineral buildup, and cleaned the components to restore proper flame sensing and ignition reliability. Verified safe, normal furnace operation after reassembly.

Evaluated and scoped an upgrade of the existing 100-amp overhead service to a 200-amp service, including replacement of the main panel and meter-to-panel service entrance conductors that enter directly through the exterior wall. Inspected the existing recessed basement breaker panel and confirmed that no interior rewiring is required beyond transferring the existing branch circuits to the new 200-amp panel.

Performed annual furnace tune-up, inspecting and servicing the heating system components to verify safe, efficient operation. Inspected and cleaned the opened component housing, which showed signs of moisture and condensation, and confirmed the unit was left in proper working order with no humidifier installed.

Responded to a follow-up complaint of a leaking toilet and a kitchen faucet sprayer that would not shut off. Pulled the toilet, removed the failed wax seal residue from the drain outlet, and reset the toilet on a new seal over the newly installed vinyl plank flooring. Secured the base and checked the supply line and valve connections for leaks. Kitchen faucet and sprayer replacement was requested but not confirmed in the photos, so warranty review and replacement status should be verified separately.

Diagnosed and repaired faulty receptacle/plug issues, restoring proper electrical function and verifying safe operation. Confirmed the wall-mounted Hunter digital thermostat is powered, intact, and displaying correctly, with the LCD reading 71° and responsive temperature controls.

Responded to a no-heat call on an 8-year-old Goodman furnace that cycled on but failed to produce heat. Inspected the inducer motor assembly, pressure switch circuit, capacitor, and associated wiring and connections, and cleaned dust and debris buildup from the components. Verified proper pressure switch operation and electrical connections, and tested the furnace through a full heating cycle to confirm normal operation and heat production.

Installed a new Bradford White gas-fired water heater on a metal drain pan, connecting copper supply lines with shutoff valves and tying the draft hood into the existing metal flue vent. Connected the gas control valve and routed the drain line to the existing condensate drain. Verified all connections were secure with no leaks, rust, or damage visible, and left the work area clean and operational.

Installed a new gas furnace in the basement mechanical area, connecting it to the existing supply and return ductwork, humidifier, gas supply, and venting. Completed electrical and control connections, mounted the thermostat, and installed a new air filter. Verified proper system operation and left the work area clean.

Performed an on-site evaluation and furnace replacement estimate for a non-operational Lennox gas furnace in a confined mechanical closet, documenting the existing venting, ductwork, refrigerant line, and electrical connections to scope the changeout. Also assessed a 30-year-old Bradford White atmospheric-vent gas water heater reported to be leaking from the top of the tank, and prepared a bundled replacement quote for both units.

Performed a comprehensive furnace tune-up on a 9-year-old unit, including inspection of the combustion and airflow components and verification of proper operation of the digital thermostat controls and wiring connections. Inspected the whole-home Honeywell humidifier, including the water supply and drain lines, damper setting, and ducting, and confirmed the unit is properly set for winter operation with no leaks, rust, or damage observed. System was found to be in good working condition and operating as intended.

Performed an on-site evaluation of a non-operational 22-year-old Tempstar upright gas furnace with an attached evaporator coil cabinet and an air-exchange unit, and documented the equipment, flue, condensate drain, and gas piping with photos. The furnace was found intact with no visible rust, frost, or damage, though a small amount of airflow was reported coming from the unit while idle, and the system's age warrants replacement consideration. A replacement estimate was presented, and the homeowner is weighing their options.

Evaluated a 40-gallon gas-fired water heater with a failed, corroded tank leaking onto the floor and documented the existing installation, including the galvanized draft hood and flue venting, copper supply lines with shutoff valve, and corroded iron gas piping. Prepared a replacement estimate for the unit, with the customer requesting expedited installation.

Responded to a no-cool call on a 6-year-old outdoor split system and performed a full diagnostic of the air handler, including inspection of the evaporator coil and cabinet interior, where the insulation lining showed uneven, deteriorated surface conditions. Evaluated system operation and electrical/control components to determine the cause of the unit failing to start. Findings were documented with photos and the system's condition reviewed with the homeowner.

Replaced toilet flush valve and fill valve assembly due to malfunction. During inspection, discovered the water inlet supply line to the toilet tank was damaged and actively leaking, requiring temporary containment with towels. Replaced the faulty water supply line and shutoff valve connection to eliminate the leak. Inspected and verified proper operation of newly installed flush valve and fill valve assembly to ensure complete system functionality.

Responded to heating complaint regarding insufficient temperature in one bedroom. Inspected HVAC ductwork and found airflow restriction at branch duct serving affected room. Verified duct connections and damper positions throughout system. Documented existing ductwork configuration in unfinished space showing proper installation of main trunk line and branch takeoffs. System operating within normal parameters at air handler. Recommended follow-up to assess damper adjustment or potential duct sizing modifications to improve airflow distribution to underperforming zone.

Completed full installation of new HVAC furnace and water heater system in basement utility area. Installed rectangular HVAC unit with metallic finish, connected refrigerant lines along wall studs, and routed silver metallic ductwork from unit. Installed cylindrical water heater with white PVC venting piping, mounted circulator pump on top, and connected all necessary plumbing lines. All systems tested and operational upon completion.

Responded to callback for sink repair reevaluation following previous estimate. Conducted thorough inspection of bathroom sink and faucet assembly. Assessed chrome two-handle faucet and porcelain basin for operational issues and potential repair requirements. Documented existing conditions with photographs for updated estimate preparation. Evaluated hardware components and plumbing connections to determine scope of necessary repairs versus previous assessment.

Responded to urgent plumbing leak affecting main level shower with water intrusion to lower level/basement. Cut access opening in wall to expose shower valve assembly and supply lines. Upon inspection, identified water staining and damage on wooden framing members surrounding vertical supply pipes. Traced leak source to shower mixing valve connections where brass fittings interface with PEX supply lines. Documented existing conditions including compromised wood framing, valve mounting configuration with blue brackets, and PVC drain assembly. Photographed all findings for repair assessment and provided recommendations for valve replacement and water-damaged framing remediation to restore safe shower operation.

Relocated copper water supply piping and shut off valve to accommodate installation of new stud wall in basement area. Provided estimate for work prior to completion, then successfully repositioned plumbing components to allow for framing modifications while maintaining proper water supply functionality and access to shutoff valve.

Completed comprehensive ASTU-AC Super Tune-up on a 15-year-old air conditioning system and 9-year-old International Comfort Products furnace (Model G9MXE08017I6A1, manufactured January 2014). Performed full system inspection, cleaned components, verified operational parameters, and documented equipment specifications for new homeowners' maintenance records.